Effects of ethylene-octene copolymer (POE) on the brittle to ductile transition of high-density polyethylene/POE blends

Three kinds of ethylene-octene copolymers (POE) were melt-blended with high-density polyethylene (PE-HD) in different proportions. Detailed characterizations were conducted to analyze their structural differences of POE and its effects in toughening PE-HD. The higher molecular weight POE can improve the toughness of PE-HD. 60:40 PE-HD/POE is elongated to break up to 700% while impact strength is 84.7 kJ/m² at −30°C, which is 21-fold of PE-HD. In the brittle to ductile transition (BDT) during impact, the fracture mechanism changes from the crazing mode to the shear yield-plastic deformation mode. The BDT temperature decreases as the POE molecular weight and its content increase. The interface strength in tension is estimated to access their effects. The Boltzmann-type models were successfully extended to describe the typical S-shaped curves in BDT of notched impact strength vs POE content or temperature. The supplementary decay model is suggested for the attenuation in toughening. Transition map in impact is proposed to select the use range of composition (c ) and temperature (T ) for high toughness. The curves are converted into 3D graph of T -c -impact strength for illustrating their coupling-separate effects, and further into the contour map of impact strength in T -c space for finding their partial equivalence.     

Road Extraction from High Resolution Remote Sensing Image based on Shape Analysis with Gestalt Theory

Simulating the psychological experience of human vision，a road extraction model based on the format tower is proposed to extract the road in the high resolution remote sensing image from the perspective of morphology.Firstly，based on the spectral and texture information，the suspected road targets are extracted by using segmentation technology.Then these targets are classified according to their reliability and extract the road targets for each category.Finally，three types of identified road information are verified and merged，and the continuous smooth road extraction results are obtained.Experiments on real high resolution images show that the results are consistent with the visual perception of the human eye，and the overall classification accuracy is higher，indicating that the algorithm is effective and feasible and has good use value.     

Tuning effect of silicon substitution on magnetic and high frequency electromagnetic properties of R2Fe17 and their composites

In this work, we report the tuning effect of the Si substitution on the magnetic and high frequency electromagnetic properties of R₂Fe₁₇ compounds and their paraffin composites. It is found that the introduction of Si can remarkably improve the magnetic and electromagnetic properties of the R₂Fe₁₇ compounds, making the R₂Fe_17–xSi_x-paraffin composites excellent microwave absorption materials (MAMs). By introducing the Si element, their saturation magnetizations decrease slightly, while much higher Curie temperatures are obtained. Furthermore, better impedance match is reached due to the decrease of the high-frequency permittivity ε′ by about 40%–50%, which finally enhances the performance of the microwave absorption. The peak frequency (f_RL) of the reflection loss (RL) curve moves toward high frequency domain and the qualified bandwidth (QB, RL ≤ ?10 dB) increases remarkably. The maximum QB of 3.3 GHz (12.0–15.3 GHz) is obtained for the Sm_1.5Y_0.5Fe₁₅Si₂-paraffin composite (d = 1.0 mm) and the maximum RL of ?53.6 dB is achieved for Nd₂Fe₁₅Si₂-paraffin composite (d = 2.2 mm), both surpassing most of the reported MAMs. Additionally, a distinguished dielectric microwave absorption peak is observed, which further increases the QB in these composites.     

2A12铝合金化学铣切加工工艺探讨

为了精确加工2Al2铝合金,探讨了化铣时间和温度对其化铣速率及表面粗糙度的影响,采用现代技术对化铣工件的力学性能进行了测试与分析.结果表明:延长非化铣部位保护胶固化时间并使保护部位向非加工面位移3～5 mm可很好地解决未化铣区域的腐蚀问题;随化铣时间的延长,化铣速率降低,且化铣温度与化铣速率呈现正相关性;化铣表面的粗糙度随化铣时间的延长而增加,随化铣温度的升高呈先减小后增加的趋势;化铣后材料的抗拉强度和屈服强度均有所提高.     

象山煤矿11~#煤层带压开采危险性预测

采用突水系数法对象山煤矿北一采区11#煤层突水危险性进行了预测,结果显示,北一采区西北角、东南角属于相对安全区,突水系数0.06 MPa/m,北一采区北部B6孔附近为相对危险区,突水系数在0.1~0.119 MPa/m之间,其它区域处在临界区。该研究成果可为矿井防治水提供参考依据。     

提升机电流不平衡问题原因分析

某水泥厂钢丝胶带提升机（下文简称提升机）的驱动电机为三相异步电动机，其型号为：YE3-280M-4/90 kW，技术参数为：380 V/50 Hz/IP55/B3/F。在提升机空载试车过程中，电机三相电流出现不平衡现象，偏差达到了12%，实测三相电流数值分别为：60 A、65 A、75 A，其对应的三相电压分别为399 V、402 V、402 V。 针对上述现象，我们对产生三相电流不平衡的原因进行归纳，并对每种原因进行实验研究，最终得出了较为客观的结论。     

Unsteady free convection of second‐grade nanofluid with a new time‐space fractional heat conduction

The Caputo and Caputo–Fabrizio derivative are applied to study a second‐grade nanofluid over a vertical plate. A comparative analysis is presented to study the unsteady free convection of a second‐grade nanofluid with a new time–space fractional heat conduction. The governing equations with mixed time–space fractional derivatives are non‐dimensionalized and solved numerically, and a comparison between the Caputo and the Caputo–Fabrizio models is made. It is found that the temperature is higher for the Caputo–Fabrizio fractional model than the Caputo model, but the higher velocity only exists near the vertical plate for the Caputo–Fabrizio model than the Caputo model. Moreover, the velocity for the Caputo model will exceed the Caputo–Fabrizio model as y evolves.     

Corrosion behavior of Cu–Sn bronze alloys in simulated archeological soil media

The corrosion behavior of synthetic Cu–Sn bronze alloys with six different Sn contents was examined through an electrochemical test and a synthetic test in a simulated corrosive medium. The mechanism of corrosion and the morphology of the corroded surfaces were characterized through field emission scanning electron microscopy equipped with energy-dispersive spectroscopy. At the corrosion potential, the corrosion behavior appears to be determined by the charge transfer step and the diffusion process. It was found that the bronze-IV (Cu–26.8Sn) specimen exhibited the best corrosion resistance, as evidenced by a low corrosion current density and a high impedance. This improvement resulted from an increase in the content of the Cu–Sn solid solution in the alloy, which was conducive to forming a relatively more protective passive film on the surface of the bronze alloy. This finding would be valuable in the anticorrosion protection of archeological artefacts after their excavation.     

以辉锑矿为原料放电等离子烧结快速制备黝铜矿Cu_(12)Sb_4S_(13)及反应机理

采用辉锑矿为原料成功制备出Cu_(12)Sb_4S_(13)块体。研究以Sb_2S_3矿物为原料时烧结工艺对Cu_(12)Sb_4S_(13)合成的影响。在400 ～ 440℃温度区间内均可快速合成Cu_(12)Sb_4S_(13)块体且二次烧结能够进一步减小中间相CuSbS_2和Cu_3SbS_3。第二相Cu_3SbS_4和残留相CuS随着烧结时间的延长而降低。二次烧结前进行机械化球磨处理,干磨比湿磨更容易减小残留相。初次烧结块体的断面SEM和EDS能谱分析表明内部存在Cu或Cu_2S颗粒团聚现象。适当降低Cu或CuS摩尔量(化学计量比0.1 mol)能促进烧结块表面反应进行。烧结过程中,硫磺蒸汽压的导致烧结块表面成分和内部粉末的成分不同。     

AD HOC网络管理综述

由于AD HOC网络自身的特点，其网络管理很多方面与固定网络不同，如移动性管理和体系结构管理等。讨论了AD HOC网络管理的各个方面，并列举了各个方面的设计思路和已有的相关算法的简介。