Heat evolution of high-volume fly ash concrete

In this paper, the results of a laboratory investigation conducted with heat evolution of high-volume fly ash (HVFA) concrete are presented. Heat evolution of concrete was studied by measuring the temperature increase in concrete under adiabatic curing condition. Characteristic of heat evolution of fly ash concrete was found to be strongly dependent on the replacement level of fly ash and dosage of superplasticizer used to maintain workability. It was also found that using fly ash as cement replacement resulted in a reduction on the maximum temperature rise. Increasing the replacement level of fly ash caused lower temperature rise in concrete. Superplasticizer caused a delay in peak temperature rise time; this is taken as an indicator that high-dosage superplasticizer used in concrete caused retardation in hydration of cement. Concretes having similar ingredients showed similar peak temperature rise whether they are superplasticized or not.     

Synthesis Routes and Characterization of High-Purity, Single-Phase Gallium Nitride Powders

Synthesis of high-purity, single-phase gallium nitride powder has been achieved in a hot-wall tube furnace via (i) the reaction of gallium with ammonia (NH₃) and (ii) the conversion of gallium oxide (Ga₂O₃). For complete reaction, the optimum temperatures, NH₃ flow rates, and boat positions relative to the NH₃ inlet were 975°C, 400 standard cubic centimeters per minute (sccm), and 50 cm, respectively, for the gallium-NH₃ reaction, and 1050°C, 500 sccm, and 50 cm, respectively, for the Ga₂O₃ conversion. Polyhedra of various shapes were obtained from both processes; some rod-shaped crystals also were observed in the material derived from Ga₂O₃.     

Ultrasonic study of molecular association of poly(vinyl chloride) solution in tetrahydrofuran

Ultrasonic absorption, velocity, adiabatic compressibility, relaxation time and relaxation amplitude measurements are reported on poly(vinyl chloride) (PVC) solution in tetrahydrofuran (THF) using pulsed ultrasonic apparatus operating at 2 MHz and 313 K. Results show a linear increase of velocity. density, viscosity, absorption coefficient, relaxation time and relaxation amplitude values with the increase of PVC concentration in THF. In contrast the compressibility decreases with increasing PVC concentration. This suggests interaction between PVC and THF molecules.     

Polymerization of isoprene in n-heptane with triethylaluminum–titanium tetrachloride catalyst. I. Effect of Al/Ti ratio on stereoregularity,conversion, molecular weight,and molecular weight distribution

The influence of the Al/Ti ratio of the heterogeneous Ziegler–Natta catalyst system AlEt₃–TiCl₄ on the isoprene polymerization in n-heptane at 30°C in a bench scale reactor was investigated. Each batch run consisted of 50 mL isoprene, 200 mL n-heptane with 0.45 and 0.5g catalyst. Conversion of isoprene and molecular weights of polyisoprene increased with increasing Al/Ti ratio, reaching their maxima values at 1.0 and 1.2, respectively. Conversion and molecular weights decreased remarkably at a higher ratio of Al/Ti. As this ratio decreases from the value of 1.2 to 0.4, the cis1,4 content in polyisoprene decreased from 97 to 25%. When the ratio of Al/Ti increased from 1.2 to 2.2 the cis-1,4 structure of polyisoprene decreased from 97 to 85%.     

Quantitative preparation of long chain thioethers from an oxo-trans-2-enoic ester and a 9,12-dioxo-trans-10-enoic acid

Branched-chain thioethers have been prepared from methyl 4-oxo-trans-2-hexadecenoate and 9,12-dioxo-trans-10-octadecenoic acid. The reagents involved in these preparations were mercaptoacetic and mercaptopropionic acids. The yields of these thioethers are almost quantitative.     

Role of sand on curing of partex surface by UV radiation

A partex surface was modified by a UV‐curing system with epoxy acrylate (EB‐600). A set of formulations was prepared with oligomer and the trifunctional monomer trimethylol propane triacrylate in different combinations of percentages (1–5%) of sand to study the role of sand in various physical properties of UV‐cured thin films, as well as partex surfaces. Increased pendulum hardness (PH), gloss, adhesion, and abrasion values were obtained by the addition of sand into the partex surfaces. The best results were obtained with the formulation containing 3% sand. An enhanced PH and a decreased percentage of gel content of the UV‐cured film was observed with an increase of the sand concentration. A simulated weathering test was performed with partex surfaces cured by a formulation containing 3% sand in the base coat. The losses of the physical properties were found to be lower over the surface treated with the formulation containing sand. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2385–2392, 2002     

Synthesis of tetrazole from α, β—Unsaturated carbonyl fatty acid

Methyl 4-oxo-trans-2-octadecenoate (II), when treated with excess hydrazoic acid in the presence of BF₃-etherate, produced 66% methyl 5-aza-nonadec-trans-2-enoate (4,5-d)-tetrazole (III), 10% methyl 5-aza-nonadec-4-oxo-trans-2-enoate (IV) and 7% pentadecamide (V). Individual products were characterized by spectral and elemental methods.     

Spatio‐temporal geometry fusion for multiple hybrid cameras using moving least squares surfaces

Multi‐view reconstruction aims at computing the geometry of a scene observed by a set of cameras. Accurate 3D reconstruction of dynamic scenes is a key component for a large variety of applications, ranging from special effects to telepresence and medical imaging. In this paper we propose a method based on Moving Least Squares surfaces which robustly and efficiently reconstructs dynamic scenes captured by a calibrated set of hybrid color+depth cameras. Our reconstruction provides spatio‐temporal consistency and seamlessly fuses color and geometric information. We illustrate our approach on a variety of real sequences and demonstrate that it favorably compares to state‐of‐the‐art methods.