Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

Catalytic epoxidation of olefins in the presence of a vanadyl porphyrin complex

It was found that vanadyl porphyrin complexes synthesized from petroleum metal porphyrin concentrates stimulated epoxidation during the olefin oxygenation process. The yields of obtained oxiranes turned out to be 38–75%, depending on the olefin structure. An epoxidation mechanism that suggests the formation of a protonated dioxygen adduct as an intermediate during oxygenation of olefins in the presence of vanadyl porphyrin complexes was proposed. An analogy is drawn between the epoxide formation reaction upon the catalytic oxygenation of olefins and the Prilezhaev reaction.     

Vacuum degassing of chromium-nickel-molybdenum steel at the Magnitogorsk Metallurgical Combine

The Magnitogorsk Metallurgical Combine has conducted a study of the effect of technological factors on the hydrogen content of chromium-nickel-molybdenum steel after vacuum degassing. It was established that the most important factor is the hydrogen content of the steel before the degassing operation. The study also determined the effects of the circulation coefficient, the duration of the degassing operation, and the vacuum used in the treatment. __________ Translated from Metallurg, No. 7, pp. 68–69, July, 2006.     

Comprehensive heat exchange model for a semiconductor laser diode

By measuring the total energy flow from an optical device, we can develop new design strategies for thermal stabilization. Here we present a comprehensive model for heat exchange between a semiconductor laser diode and its environment that includes the mechanisms of conduction, convection, and radiation. We perform quantitative measurements of these processes for several devices, deriving parameters such as a laser's heat transfer coefficient, and then demonstrate the feasibility of thermal probing for the nondestructive wafer-scale characterization of optical devices.     

Experimental studies of the bond response of three-wire strands and some influencing parameters

The bond behavior of prestressing strands is of great importance for the capacity of precast prestressed concrete structures. In the present study, the bond behavior of three-wire strands, and some influencing parameters, were examined by means of steel encased pull-through and push-in tests. The three mechanisms: adhesion, friction and other mechanical actions were found to be present at the strand-concrete interface at different slip values. The results from the experiments showed that the micro roughness of the strand surface strongly affected the initial bond response of the strand, that is the adhesion in the interface. The maximum bond capacity of indented three-wire strands was found to be directly connected to the geometric properties of the strand indents. The influence of the concrete strength on the bond capacity of the strand was hard to interpret. However, the density of the concrete matrix was found to be a better parameter for determine the influence of the concrete rather than the compressive strength.     

Metalorganic chemical vapor deposition of silver thin films for future interconnects by direct liquid injection system

Deposition of Ag films by direct liquid injection-metal organic chemical vapor deposition (DLI-MOCVD) was chosen because this preparation method allows precise control of precursor flow and prevents early decomposition of the precursor as compared to the bubbler-delivery. Silver(I)-2,2-dimethyl-6,6,7,7,8,8,8-heptafluoro-3,5-octanedionato-triethylphosphine [Ag(fod)(PEt₃)] as the precursor for Ag CVD was studied, which is liquid at 30 °C. Ag films were grown on different substrates of SiO₂/Si and TiN/Si. Argon and nitrogen/hydrogen carrier gas was used in a cold wall reactor at a pressure of 50–500 Pa with deposition temperature ranging between 220 °C and 350 °C. Ag films deposited on a TiN/Si diffusion barrier layer have favorable properties over films deposited on SiO₂/Si substrate. At lower temperature (220 °C), film growth is essentially reaction-limited on SiO₂ substrate. Significant dependence of the surface morphology on the deposition conditions exists in our experiments. According to XPS analysis pure Ag films are deposited by DLI-MOCVD at 250 °C by using argon as carrier gas.     

The anisotropic effect of a weak magnetic field on the photoconductivity of C<Subscript>60</Subscript> single crystals

The effect of crystal orientation on the photogeneration of free charge carriers was studied for C₆₀ single crystals in a weak magnetic field. The photoconductivity sharply depends on the orientation of magnetic field with respect to the crystallographic directions, showing a 5–8% increase for seven axes of the C₆₀ crystal.     

State of polarization changes: Classification and measurement

We propose a standardization procedure that provides a convenient, quantitative and reproducible laboratory-based method for measuring the state of polarization (SOP) fluctuations produced by polarization varying devices. This method is based on the SOP distributions generated by commercial polarization scramblers. We show that these devices generate distributions of the maximum change of the SOP (in a given sample time) that follow Rayleigh statistics, which scale linearly with scrambling frequency and the sample time. We use this procedure to measure the SOP fluctuations in a short length of coiled fiber subject to mechanical perturbations.     

Stress-strain relations in elastoplastic solids with Dugdale-type cracks

Mechanical behavior of a two-dimensional elastoplastic solid with rectilinear cracks is investigated. Plastic strip model is used to reduce plasticity problem to the equivalent linear elasticity formulation. Two realizations of the mixed mode plastic strip model are considered: in-line plastic strips as proposed by Becker and Gross [Int. J. Fract. 37 (1988) 163], and inclined plastic strips of Panasyuk and Savruk [Appl. Mech. Rev. 47 (1994) 151]. The effective mechanical response predictions are based on the procedure presented in Kachanov et al., [Appl. Mech. Rev. 47 (1994) 151]. Stress-strain relations are obtained for parallel and randomly oriented non-interacting cracks. Results are compared with known elastic solutions.