飞行人员骨密度与内分泌调节关系的探讨

对37名骨密度(BD)低下的飞行员(实验组)和BD正常的48名飞行员、100名地面人员(正常对照组)进行了BD和血清TT_3、TT_4、TSH IRMA、CT、PTH、E_2和T放射免疫测定。结果显示,实验组BD均值明显低于对照组(p<0.01),血清TT_3、TT_4、CT、E_2(女性)和T(男性)均值与对照组比较,大多数年龄存在着显著或非常显著差异(p<0.05或p<0.01)。同时对飞行人员BD与几种内分泌激素关系进行了探讨。     

Effects of Sc2O3 and MgO passivation layerson the output power of AlGaN/GaN HEMTs

The low temperature (100°C) deposition of Sc₂O₃ or MgO layers is found to significantly increase the output power of AlGaN/GaN HEMTs. At 4 GHz, there was a better than 3 dB increase in output power of 0.5×100 μm² HEMTs for both types of oxide passivation layers. Both Sc₂ O₃ and MgO produced larger output power increases at 4 GHz than conventional plasma-enhanced chemical vapor deposited (PECVD) SiN_x passivation which typically showed ⩽2 dB increase on the same types of devices. The HEMT gain also in general remained linear over a wider input power range with the Sc₂O₃ or MgO passivation. These films appear promising for reducing the effects of surface states on the DC and RF performance of AlGaN/GaN HEMTs     

《无机及分析化学》在多媒体教学的应用及思考

对多媒体技术在无机及分析化学教学的应用进行了，阐述和分析，指出使用多媒体教学应注意的问题。     

A helical drive in-pipe robot based on compound planetary gearing

The modern society is fuelled by very comprehensive grids of gas and liquid pipelines. In recent years, various in-pipe robots have been developed for inspection and maintenance tasks inside such pipes. In this paper, a novel in-pipe robot is proposed and developed for gas/oil well interventions at thousands of meters downhole. Due to the nature of such intervention, in-pipe robot design must be capable of carrying a very large payload, as large as 2500?N inside a pipe with diameter as small as 54?mm. The proposed design concept is based on a compound planetary gearing system. One of the major novelties of this design is the use of pipe wall as a ring gear for one stage of the compound planetary gear system; the other novelty is the generation of helical angle when the planetary gears are expanded to press on the pipe wall. The proposed concept is compact, efficient, and has never been reported before. In this paper, the helical angle, the velocity, and load capability of the proposed system will be analyzed. The load transportation capability of the proposed robot is also measured based on an experiment. Initial data have shown great potential in carrying large payloads.     

沉淀铁催化剂上F-T合成反应的研究

制备了物相组成为 Quartz- Si O2 ,Hermatite- Fe2 O3 和 Fe2 O3 - Iron Oxide的沉淀铁催化剂 ,研究了该催化剂作用上固定床积分反应器中费托合成反应特性 .发现 2 .6MPa,80 0 h-1,H2 /CO=2 /3,2 60℃～ 2 90℃时 ,随着温度的升高 ,CO和 H2 的转化率增大 ,CO2 选择性减小 ;40 0 h-1,65 0 h-1,80 0 h-1低空速和 2 4 0 0 h-1,32 0 0 h-1,40 0 0 h-1,640 0 h-1高空速时 ,随着空速的升高 ,H2转化率、CO转化率选择性下降 ,CO2 的选择性升高 ;2 80℃ ,2 .6MPa,H2 /CO进料比 2 /3,1 /1 ,2 /1时 ,随着 H2 /CO进料比的增加 ,CO转化率 ,H2 /CO利用比和 CH4选择性都增加 ,H2 转化率和 CO2选择性减小 .     

Electrochemical performance of nanocrystalline Li3V2(PO4)3/carbon composite material synthesized by a novel sol–gel method

A novel sol–gel method based on V₂O₅·nH₂O hydro-gel was developed to synthesize nanocrystalline Li₃V₂(PO₄)₃/carbon composite material. In this route, V₂O₅·nH₂O hydro-gel, NH₄H₂PO₄, Li₂CO₃ and high-surface-area carbon were used as starting materials to prepare precursor, and the Li₃V₂(PO₄)₃/carbon was obtained by sintering precursor at 750 °C for 4 h in flowing argon. The sol–gel synthesis ensures homogeneity of the precursors and improved reactivity. The sample was characterized by XRD, SEM and TEM. X-ray diffraction results show Li₃V₂(PO₄)₃ sample is monoclinic structure with the space group of P2₁/n. The TEM image indicates that the Li₃V₂(PO₄)₃ particles modified by conductive carbon are about 70 nm in diameter. The Li₃V₂(PO₄)₃/carbon system showed that the discharge capacities in the first and 50th cycle are about 155.3 and 143.6 mAh/g, respectively, in the range of 3.0–4.8 V. The sol–gel method is fit for the preparation of Li₃V₂(PO₄)₃/carbon composite material which may offer some favorable properties for commercial application.     

捣固炼焦在中国焦化工业发展中的前景与展望

介绍了我国炼焦煤源的现状、捣固炼焦的理论依据,并将捣固炼焦技术与常规炼焦方法进行了比较,指出捣固炼焦应向大型化方向发展,并提高捣固和装煤的自动化水平,发展捣固炼焦可促进我国焦化工业的可持续发展。