Effect of Sb implantation on copper silicides formation and morphology after annealing of Cu/Si structures

In this work, the solid state reaction between a thin film of copper and silicon has been studied using Rutherford backscattering spectroscopy, X-ray diffraction, scanning electron microscopy and microprobe analysis. Cu films of 400 and 900 Å thicknesses are thermally evaporated on Si(1 1 1) substrates, part of them had previously been implanted with antimony ions of 5×10¹⁴ or 5×10¹⁵ at. cm⁻² doses. The samples are heat-treated in vacuum at temperatures in the range 200–700 °C for various times. The results show the growth and formation of Cu₃Si and Cu₄Si silicides under crystallites shape dispatched on the sample surface, independently of the implantation dose. On the other hand, it is established that the copper layer is less and less consumed as the antimony dose increases, resulting in the accumulation of Sb⁺ ions at silicide/Si interface and in the silicide layer close to surface. The exposure of samples to air at room temperature shows the stability of Cu₄Si phase whereas the Cu₃Si silicide disappears to the benefit of the silicon dioxide formation. The observed phenomena are discussed.     

A VQ-based blind image restoration algorithm

Learning-based algorithms for image restoration and blind image restoration are proposed. Such algorithms deviate from the traditional approaches in this area, by utilizing priors that are learned from similar images. Original images and their degraded versions by the known degradation operator (restoration problem) are utilized for designing the VQ codebooks. The codevectors are designed using the blurred images. For each such vector, the high frequency information obtained from the original images is also available. During restoration, the high frequency information of a given degraded image is estimated from its low frequency information based on the codebooks. For the blind restoration problem, a number of codebooks are designed corresponding to various versions of the blurring function. Given a noisy and blurred image, one of the codebooks is chosen based on a similarity measure, therefore providing the identification of the blur. To make the restoration process computationally efficient, the principal component analysis (PCA) and VQ-nearest neighbor approaches are utilized. Simulation results are presented to demonstrate the effectiveness of the proposed algorithms.     

Effect of the Distribution of Manganese Ions on the Properties of Mn-Doped (Ba,Y)TiO3 PTCR Ceramics

The electrical properties and microstructure of (Ba,Y)TiO₃ PTCR ceramics were studied. The results indicate that the Mn ions increase the intergranular barrier height and produce a high-resistance layer on the grain surface. The temperature-dependent resistances of the grain bulk, surface layer, and grain boundaries, the temperature coefficient of resistance, and the magnitude of the varistor effect were assessed as a function of Mn content.     

On trading wavelengths with fibers: a cost-performance based study

We consider the effect of multiple fibers on wavelength division multiplexing networks without wavelength conversion. We study networks with dynamic wavelength routing and develop accurate analytical models to compare various possible options using single- and multiple-fiber networks. We use results of an analytical model and simulation-based studies to evaluate the blocking performance and cost of multifiber networks. The number of fibers required providing high performance in multifiber networks and their costs are compared. A case is made for using multiple fibers in each link with fewer wavelengths instead of using a single fiber with many wavelengths. In particular, we show that a network with four fibers per link and with four wavelengths on each fiber without any wavelength conversion on any node yields similar same performance as the networks with one fiber per link and 16 wavelengths per fiber on each link and with full wavelength conversion capability on all nodes. In addition, the multifiber network may also offer the cost advantage depending on the relative cost of components. We develop a parametric cost model to show that multiple fibers in each link are an attractive option. Finally, such multifiber networks also has fault tolerance, with respect to a single fiber failure, already built into the system.     

Nonstationary Simulation Model of Absorber with Falling Film of Suspension

A nonstationary model of SO₂ absorption from a gas phase to a countercurrent falling film of absorbing slurry was developed. Laminar, wavy and turbulent film structures were considered based on published information. Resistances to the mass transfer on the gas and the liquid sides of the interphase were considered, together with chemical reactions in the liquid phase. Relevant chemical equilibria in the liquid phase were modeled. Original experimental data on the neutralization reagent dissolution rate presented as a polydispersed two‐phase system of solids and on the rate of dissolved sulfite oxidation were used. The model was verified with experimental data from a laboratory‐scale falling‐film absorber using a single vertical tube under various geometrical and operating conditions, and a very good agreement was found with the experiment. Parametric sensitivity analysis showed the critical parts of the model.     

Structural Changes Induced in Nonstoichiometric Titanium Carbide by High-Temperature Deformation

The microstructure evolution in nonstoichiometric titanium carbide is studied during high-temperature deformation at high strain rates and low strains (shock compression) and at slow strain rates and high strains (superplastic regime). The results demonstrate that high-temperature deformation in a broad range of strain rates offers a means of controlling the microstructure of titanium carbide. By varying deformation conditions, one can obtain materials differing in microstructure and chemical composition, in particular, with equilibrium and nonequilibrium microstructures. Accordingly, the physicochemical properties of such materials also differ.     

Characteristic Features of the Optimal Processing of the Results of Measurements in the Case of a Random Observation Function

An analysis is made of the characteristic features and problems of the optimal processing of the results of measurements in the case of a random observation function utilizing a nonlinear Kalman filter. A method is proposed for increasing the convergence domain of the filter with additional processing of measurements in the frequency domain.     

Influence of device engineering on the analog and RF performances of SOI MOSFETs

This work presents a systematic comparative study of the influence of various process options on the analog and RF properties of fully depleted (FD) silicon-on-insulator (SOI), partially depleted (PD) SOI, and bulk MOSFET's with gate lengths down to 0.08 /spl mu/m. We introduce the transconductance-over-drain current ratio and Early voltage as key figures of merits for the analog MOS performance and the gain and the transition and maximum frequencies for RF performances and link them to device engineering. Specifically, we investigate the effects of HALO implantation in FD, PD, and bulk devices, of film thickness in FD, of substrate doping in SOI, and of nonstandard channel engineering (i.e., asymmetric Graded-channel MOSFETs and gate-body contacted DTMOS).     

河床变形对水电站动力设备工作条件的影响

水电站运行过程中河床变形会使河底高程逐渐降低。从而导致下游流量特性曲线下降以及水电站水头增大。水头增大使水电站气蚀特性发生变化，导致动力设备的正常工作条件受到破坏。并对其运行安全性和效率造成不利影响。以卡马河的沃特金水电站为例，阐述了河床变形对水电站动力设备工作条件的影响。     

Static energy reduction techniques for microprocessor caches

Microprocessor performance has been improved by increasing the capacity of on-chip caches. However, the performance gain comes at the price of static energy consumption due to subthreshold leakage current in cache memory arrays. This paper compares three techniques for reducing static energy consumption in on-chip level-1 and level-2 caches. One technique employs low-leakage transistors in the memory cell. Another technique, power supply switching, can be used to turn off memory cells and discard their contents. A third alternative is dynamic threshold modulation, which places memory cells in a standby state that preserves cell contents. In our experiments, we explore the energy and performance tradeoffs of these techniques. We also investigate the sensitivity of microprocessor performance and energy consumption to additional cache latency caused by leakage-reduction techniques.