荧光染料用于涤纶织物染色的荧光性能研究

在实验条件下，染色织物的荧光反射率随荧光染料的浓度增加而增加，超过一定浓度后，有下降趋势；在pH=5左右，荧光反射率最高；荧光增白剂会提高染色织物的荧光反射率，在荧光黄2GFL中，当荧光增白剂的浓度由0.1％增加到5％时，荧光反射率由8．43增加至18．59，而对非荧光染料只有增艳的作用，不产生荧光。荧光染料染色织物的荧光反射率随着加入非荧光染料量的增加而减弱。     

Propylene epoxidation in a microreactor with electric heating

Gas phase propylene epoxidation on gold catalysts has attracted wide attention from industry and academia due to its high selectivity. However, it suffers from low propylene conversion and rapid catalyst deactivation. Experiments showed that propylene conversion could be increased by raising H₂, O₂, or C₃H₆ concentration in the feed, but the feed compositions were within the explosion limit. It was also shown that the activity of the used catalyst could be fully recovered, but the regeneration temperature was 280 °C, much higher than that for reaction. Therefore a microchannel reactor was devised to suppress explosion and was constructed with Fecralloy, to raise the temperature rapidly for catalyst regeneration by electric heating. In two minutes the temperature of the reactor could be raised from 50 to 300 °C. Catalysts were coated on the alloy belt by dip coating, and the performance of the reactor was evaluated under different operating conditions. Results showed that in the microreactor the overall reaction rate was controlled mainly by the intrinsic reaction rate, and also influenced by film diffusion to a certain extent. The deactivated catalyst was regenerated in the microchannel reactor and the activity was fully recovered.     

Relationship of threshold diameter and Darcean permeability in unconsolidated porous structures

Experiment was conducted on the threshold pressure for atmospheric air through unconsolidated narrow size distributed mini sphere and sand particles at low flow rates. The threshold diameter calculated from measured threshold pressure showed that it does not follow the traditional similarity theory. This is consistent with our experiment on accurate permeability measurement, and can be explained as a result of gas slip flow within such micro pore structure. Our current work tend to find the method to predict the permeability-threshold pressure relationship for unconsolidated porous structures.     

西门子S7系列PLC在自控系统中的应用

阐述了S7—400H应用特点使用中存在的问题、解决方案。     

国内外型焦生产工艺及发展前景

介绍了国内外型焦技术的生产工艺、型煤碳化的过程和影响因素,以及国内目前几种碳化窑炉,通过对型焦和焦炭的对比分析,指出洁净型焦生产技术的优势必然会使它在未来具有巨大的发展空间。     

Reaction kinetics study of asymmetric polymer-polymer interface

In this study, the reaction kinetics of asymmetric polymer-polymer interface was experimentally and theoretically studied. A new rheological method correlating the change of rheological property of reactive system with the conversion of the in situ formed copolymers was applied to study the reaction kinetics of PBT/epoxy reactive system. Then, the new method was proved to be useful by comparing its results with that obtained from the conventional endgroup determination method. Moreover, the conversion of PBT/epoxy reactive system from rheological method could be well fitted by the numerical analysis, from which the kinetic constant and the diffusion constant of epoxy in PBT could be determined simultaneously.     

直纺长丝工艺中聚酯熔体端羧基值控制的工业研究

本文从工业生产的实践出发对杜邦聚酯技术直接纺工艺中端羧基控制进行了研究。通过对熔体端羧基值对无油长丝端羧基、粘度及纺丝加工影响的分析 ,阐明了聚酯端羧基控制范围 ;通过摸索三个反应釜工艺条件对端羧基值的影响 ,找出了端羧基工业控制的有效途径 ,为同类技术装置生产提供了依据     

纳米SiO_2粒子在环氧树脂中的分散工艺研究

研究了纳米SiO2在环氧树脂中的均匀分散工艺,探讨了超声波振荡和超声波分散时间对纳米SiO2/EP复合材料力学性能的影响,确定了最佳分散工艺。SEM表明,采用高剪切与超声波复合分散工艺比高剪切工艺的分散效果好;测试了复合材料的力学性能,进一步证明纳米SiO2具有增韧增强作用。     

Electrochemical performance of nanocrystalline Li3V2(PO4)3/carbon composite material synthesized by a novel sol–gel method

A novel sol–gel method based on V₂O₅·nH₂O hydro-gel was developed to synthesize nanocrystalline Li₃V₂(PO₄)₃/carbon composite material. In this route, V₂O₅·nH₂O hydro-gel, NH₄H₂PO₄, Li₂CO₃ and high-surface-area carbon were used as starting materials to prepare precursor, and the Li₃V₂(PO₄)₃/carbon was obtained by sintering precursor at 750 °C for 4 h in flowing argon. The sol–gel synthesis ensures homogeneity of the precursors and improved reactivity. The sample was characterized by XRD, SEM and TEM. X-ray diffraction results show Li₃V₂(PO₄)₃ sample is monoclinic structure with the space group of P2₁/n. The TEM image indicates that the Li₃V₂(PO₄)₃ particles modified by conductive carbon are about 70 nm in diameter. The Li₃V₂(PO₄)₃/carbon system showed that the discharge capacities in the first and 50th cycle are about 155.3 and 143.6 mAh/g, respectively, in the range of 3.0–4.8 V. The sol–gel method is fit for the preparation of Li₃V₂(PO₄)₃/carbon composite material which may offer some favorable properties for commercial application.     

气体控制参数对气体辅助成型产品翘曲的影响

从气体辅助注射成型工艺的角度探讨了气体的延迟时间和第一段压力这两个关键的参数对槽的影响进而对产品翘曲变形的影响，结果表明：虽然通过使用气体辅助注射成型技术能改善产品变形，但并不能完全消除变形；造成产品变形的原因和机理十分复杂，只有进行从设计到工艺的全方位考察才能有效的控制变形，气体手指效应也是造成产品变形的一个重要因素，工艺上可以通过调整延迟时间和气体压力来减小产品的变形量。