Invasiveness of LiTaO/sub 3/ and GaAs probes in external E-O sampling

Disturbances of signals on a coplanar waveguide (CPW) induced by the presence of LiTaO/sub 3/ and GaAs electrooptic probes in external electrooptic (EO) sampling have been simulated and compared quantitatively. The finite-difference-time-domain method is used to simulate the full wave field around a coplanar waveguide on a GaAs substrate in an external EO sampling configuration. The results indicate that the induced signal disturbance, or invasiveness, of a LiTaO/sub 3/ probe is almost ten times that of a GaAs probe in terms of the magnitude of S/sub 11/, but that LiTaO/sub 3/ yields about two times the EO response for a given S/sub 11/ and optical probing wavelength. The transparency of LiTaO/sub 3/ to shorter wavelengths, however, allows an even higher sensitivity for this material relative to GaAs. The results suggest that these probes do not exhibit significant invasiveness (magnitude of S/sub 11/ smaller than -40 dB), if they are removed from contact by the distance of CPWs center conductor width.<>     

Effect of silver addition on superconductivity in the Bi1.6Pb0.4Sr1.6Ca2Cu3O10−y system

Silver/superconductor composites containing 0 to 80 vol% silver have been prepared and their properties determined. Optimum heat treatment at sintering temperatures ( 800° C) under low oxygen pressures produces material with high critical current density and improves physical properties. Magnetic susceptibility measurements have been found to be consistent with resistivity results. In order to retain a single high-T _c phase with increasing silver content, decreased oxygen partial pressures are required. Using the normal-state resistivity of these composites, a percolation threshold at a silver volume fraction of 43% was observed, while zero resistivity measurements show that a continuous superconducting network can be obtained with up to 80 vol% silver. The critical current density of 21 vol% silver-doped samples was found to be 1520 A cm^–2 at 77.3 K, compared to 260 A cm^–2 for an undoped sample.     

Scaling effects on flow hydrodynamics of confined microdroplets induced by Rayleigh surface acoustic wave

This paper reports an experimental and numerical investigation on the scaling effects in the flow hydrodynamics for confined microdroplets induced by a surface acoustic wave (SAW). The characteristic parameters of the flow hydrodynamics were studied as a function of the separation height, H, between the LiNbO₃ substrate and a top glass plate, for various droplets volumes and radio-frequency powers. The ratio of the gap height to attenuation length of the SAW, H/l _SAW, is shown to be an important parameter affecting the streaming flow induced in this confined regime. The reported numerical and experimental results are in good agreement over the range examined in this study and demonstrate that, at a lower gap heights of H?≤?100?μm, a significant decrease in streaming velocity or Reynolds number is induced, with the velocity approaching zero when the gap height is decreased to ~50?μm. An increase in the gap height results in an increased streaming velocity; however, if the gap height exceeds 70?% of the SAW attenuation length, any further increase in the gap height induces a drop in the streaming velocity.     

Laser glazing of an Fe-C-Sn alloy

Morphology and geometry of melted zones, cooling rates, microstructure and microhardness in the laser-glazed Fe-4%C-10%Sn alloy have been investigated. The computer simulation on the basis of the moving gaussian source model was used successfully to predict the maximum width and depth of the melted zone and the cooling rate. The microstructure from the surface to the bottom of the laser-melted zone is a non-crystalline phase, dendritic grains and a microcrystalline zone successively. Values of the averaged-spacing of the non-crystalline phase are 0.205⁶ and 0.121⁹nm, respectively; twinned martensites, having an axial ratioc/a of 1.128, existed in dendritic grains, and carbides of Fe₃ C at the interdendritic regions; the microcrystalline zone was composed of -Fe and a new bet (a=0.415 nm,c=0.955 nm) phase. The different microstructure in the melted zone can be explained by the results of the heat flow calculation. A fine eutectic structure (-Fe + Fe₃C) was observed in heat-affected zones. Microhardness of the eutectic structure can be predicted by the empirical relation of fracture stress to the interlamellar spacing of pearlite.     

Parallel Algorithms for Image Template Matching on Hypercube SIMD Computers

This correspondence presents several parallel algorithms for image template matching on an SIMD array processor with a hypercube interconnection network. For an N by N image and an M by M window, the time complexity is reduced from O(N2M2) for the serial algorithm to O(M2/K2 + M * log2 N/K + log2 N * log2 K) for the N2K2-PE system (1 ? K ? M), or to O(N2M2/L2) for the L2-PE system (L ? N). With efficient use of the inter-PE communication network, each PE requires only a small local memory, many unnecessary data transmissions are eliminated, and the time complexity is greatly reduced.     

Modulation on the electrical and optical properties of Na and Rh co-doped Ruddlesden-Popper layered Ca3Ti2O7

Layered perovskite Ca_2.91Na_0.09Ti_2-xRh_xO₇ (x?=?0.00, 0.02, 0.04, 0.06) were synthesized by a conventional solid-state reaction. Room temperature ferroelectricity has been confirmed. The remanent polarization increases with an increase of Rh content, which is due to a larger oxygen octahedral distortion by Rh doping. The coercive field increases with Rh doping as the pinning effect of oxygen vacancies reduce the mobility of domain wall. Remanent polarization and coercive field are caused by different mechanisms, so it is possible to modulate them independently to meet the requirement of application in ferroelectric field. The concentration of oxygen vacancy increased with Rh doping, leading to the significant increase of leakage current density. The bandgap of samples doped with Rh drastically decrease and the visible light response of the sample was improved by Rh doping due to the formation of impurity energy levels within the band gap.

     

Mold-filling characteristics of AZ91 magnesium alloy in the low-pressure expendable pattern casting process

The magnesium (Mg) alloy low-pressure expendable pattern casting (EPC) process is a newly developed casting technique combining the advantages of both EPC and low-pressure casting. In this article, metal filling and the effect of the flow quantity of inert gas on the filling rate in the low-pressure EPC process are investigated. The results showed that the molten Mg alloy filled the mold cavity with a convex front laminar flow and the metal-filling rate increased significantly with increasing flow quantity when flow quantity was below a critical value. However, once the flow quantity exceeded a critical value, the filling rate increased slightly. The influence of the flow quantity of inert gas on melt-filling rate reveals that the mold fill is controlled by flow quantity for a lower filling rate, and, subsequently, controlled by the evaporation of polystyrene and the evaporation products for higher metal velocity. Meanwhile, the experimental results showed that the melt-filling rate significantly affected the flow profile, and the filling procedure for the Mg alloy in the low-pressure EPC process. A slower melt-filling rate could lead to misrun defects, whereas a higher filling rate results in folds, blisters, and porosity. The optimized filling rate with Mg alloy casting is 140 to 170 mm/s in low-pressure EPC.     

Conductivity enhancement in transparetn ZnO films via Al-dopping produced by CW-CO2 laser-induced evaporation

Highly conductive transparent aluminium-doped ZnO (ZnO:A1) films were successfully deposited by CW-CO₂ laser-induced evaporation. Optimisation of evaporation parameters was based on laser power, substrate temperature, O₂ partial pressure in the vacuum chamber and amount of Al in the ZnO source pellet. ZnO:A1 films with an electrical resistivity as low as 6.6 × 10⁻²Ω·cm and an optical transmission of 80% at 500nm were obtained at laser power of 15 W, substrate temperature of about 200°C, O₂ partial pressure of 6—7 × 10⁻⁴ Torr and 5wt.% Al. Conductivity of ZnO films can be increased one order via Al-doping in ZnO films. The films obtained by laser-induced evaporation have compared quite favorably with the high quality films obtained by sputtering.     

用CAXA电子图板求解冲模压力中心

在模具设计中 ,冲裁模压力中心通常采用解析法或图解法求解。本文提出一种用CAXA绘图软件在设计制图时直接求解的方法 ,快速直接 ,简单方便 ,精度较高。     

环氧氯丙烷下游产品生产现状及市场前景

论述了环氧氯丙烷的主要下游产品环氧树脂、合成甘油、氯醇橡胶等的生产现状、市场前景等,指出:我国氯碱行业应该重视这些环氧氯丙烷下游精细化工产品的开发,以促进我国环氧氯丙烷的发展。