The investigation of 32P wire for catheter-based endovascular irradiation

The dose distribution from a 32P source has been measured and calculated in order to evaluate its application in endovascular irradiation. The source dimension was 27 mm in length and 0.3 mm in diameter and was embedded in the end of a Ni-Ti wire. Dose measurements were performed using radiochromic film in several specially designed tissue equivalent phantoms. Loevinger's point dose kernel was used for the calculation. The approximate dose rate at a radial distance of 1.5 mm from the center of the source was found to be 6.75 cGy/s per GBq (0.25 cGy/s per mCi), which allows the delivery of a therapeutic dose in a short time interval with a satisfactory homogeneity without stepping the source. However, the dose rate falls off almost exponentially along the radial distance. Therefore it may not be suitable for treating large diameter vessel from a centrally located source. The effect of a curved 32P wire source on the radial dose distribution was also investigated. The results showed that for a maximum bend of 180 degrees the dose rate was increased by as much as 20% along the inner radial distance but decreased by as much as 20% along the outer radial distance compared to the dose along a straight wire. However, for curvatures normally encountered in a clinical situation, the dose rate was changed less than 5%.     

Influence of Lanthanum on Fluorescence Properties of Ag-BaO Thin Films

Ag-BaO thin films doped with lanthanum were prepared by vacuum deposition. Compared with the normal Ag-BaO thin film, there is almost no change with the shape and the peak site of the fluorescence spectrum; however, fluores-cence emission strength of the whole observation band(325 -600 nm)increases about 40%, and the increase of short wavelength range is more remarkable than that of long wavelength range, which we named “blue-stronger“ phenomenon. Analytic results show that, with the forming of intermetallic compounds between silver and lanthanum, the 4f-state energy levels lie just below the Fermi level within 5 eV. It is the energy exchange between the 4f energy levels and the conduction band that causes the increase effect of fluorescence emission, and it is the optical absorption cross section of 4f electron, which increases with the increase of energy of incidence photon, that gives rise to the “blue-stronger“ phenomenon.     

前馈和反馈相结合的控制策略在宝钢线材厂控冷轧线上的应用实践

在详细分析料坯在水箱内冷却热过程特点的基础上，提出了前馈和反馈相结合的水流量优化控制策略，并将该策略应用于宝钢线材厂控冷轧线上。实际运行结果表明：该策略能够合理地控制水箱水流量，从而保证了线材水箱出口处的温度满足工艺要求，大大提高了线材成品的质量。所做工作对国内同类企业有重要的意义。     

用数采器对空压机进行状态监测预报

通过几个典型事例的分析、判断和处理，介绍了该厂怎样利用９１ｌ型数采器对２Ｄ１２—１００／８型空压机运行状态进行监测，以预报早期故障，为设备检修提供指导．     

迫零对Turbo码的性能影响

从距离谱的角度对迫零在Turbo码中的作用进行了理论分析。通过仿真，研究了迫零对Turbo码性能的影响。仿真结果表明，Turbo码编码器迫零处理有助于改善Turbo码的性能。     

车载制氧机加装预冷装置的研究与实现

航空兵部队地面保障装备之一的车载移动式制氧机，采用封闭循环水冷却，由于受到使用条件的限制，多数情况下冷却效果不尽理想，加装蒸汽压缩预冷装置，即可较好地了和低冷却系统温度，提高制冷量和整机使用寿命，又可满足整车机动性，动力等技术要求。     

PP-g-MAH对PA6/PP/TLCP三元共混物的增容改性作用

研究了PP-g-MAH对PA6／PP／TLCP三元共混体系的增容作用以及对共混物流变性能和力学性能的影响。通过共混物的DSC、SEM、POM、流变性能和力学性能测试，结果表明，PP－g-MAH对共混体系有明显的增容作用，共混物的力学性能（拉伸强度和冲击强度）得到提高；由于TLCP的加入，共混物的熔体粘度大大低于PA6的熔体粘度。     

超细氧化锌粉体的制备及尺寸控制

根据气相化学反应法 (CAD)制备超细粉的原理 ,从低品位氧化锌矿中采用火法冶金方法直接制备超细氧化锌粉 ,对所得氧化锌的粒度尺寸、微观结构和粒度分布进行测试 ;考察了冷却强度以及收集装置对超细氧化锌粒度及粒度分布的影响 ;讨论了氧化锌粉体团聚的原因及对策、试验条件对氧化锌尺寸的控制等     

西门子工业控制网络在棒材连轧生产线的应用

本文通过对包钢棒材连轧线的工业控制网络的由分体到整体的介绍,将西门子公司的三级控制网络(Profibus-DP网络、MPI网络、工业以太网)思想做了一个全面的说明.通过与现场实际相结合,使人们对这一概念有了更加清晰的认识.文章最后还结合作者的一些体会作了总结.     

纳米氧化铝的制备及应用

介绍了高科技产品纳米氧化铝的 3大制备方法 :固相法、气相法、液相法的优缺点 ,以及纳米氧化铝的应用与发展前景