物流中心选址问题的二元语义决策方法

为了有效避免语言评价中信息的损失和扭曲,从而提高物流中心选址的准确性,在层次分析法中引入三角模糊数,将各评价指标量化,提出一种二元语义决策选址方法.给出二元语义评价的方法与步骤,并通过物流中心选址的算例分析说明该方法的合理性.     

基于不完全信道信息的D2D功率分配算法

针对蜂窝与终端直通(Device-to-device,D2D)混合网络中的不完全信道状态信息(Channel state information,CSI),提出了一种基于不完全CSI的最优功率分配算法。利用拉格朗日乘数法推导出了最优功率分配解的闭式表达式。相对于传统的最大发送功率分配方案,该最优解受信道信息误差的影响较小,具有较好的鲁棒性。仿真结果表明,本文算法可以节约发送功率,并得到更大的接收信噪比。     

Influence of static pre-loading on the dynamic bending strength of concrete with particle element modeling

Experimental tests show that static pre-loading has a significant effect on the dynamic strength of concrete.Based on meso-scale particle element model,numerical simulations of dynamic bending tests with pre-loading are performed.Complete stress–strain relationships are then obtained.Significant increase in dynamic strength is found when the pre-loadings are imposed within the elastic limit of concrete.However,when the imposition of pre-loadings reaches the plastic or softening range,dynamic strengths may gradually decrease along with the increase in pre-loadings.The distribution of energy components and the failure modes are discussed to explain the mechanisms of the phenomena.     

Non-Fourier heat conduction in a thin gold film heated by an ultra-fast-laser

Based on the dual-phase-lagging(DPL)heat conduction model,the Cattaneo-Vernotte(CV)model and the improved CV model we investigate the one-dimensional heat conduction in gold films with nano-scale thickness exposed to an ultra-fast laser heating.The influence of system parameters on the temperature field is explored.We find that for all the non-Fourier heat conduction models considered in this work,a larger Knudsen number normally leads to a higher temperature.For the DPL model,the large ratio of the phase lag of temperature gradient to the phase lag of heat flux reduces the maximum temperature and shortens the time for the system to reach its steady state.The CV model and the improved CV model lead to the similar thermal wave behavior of the temperature field,but the thermal wave speeds for these two models are different,especially for large Knudsen numbers.When the phase lag of temperature gradient is smaller,the difference between the DPL model and the improved CV model is not significant,but for the large phase lag of temperature gradient the difference becomes quite significant,especially for the large Knudsen number.In addition,the effect of the surface accommodation coefficient,which is a parameter in the slip boundary condition,on the temperature field of the gold film heated by ultra-fast laser pulses is investigated based on the DPL model.     

Effects of coagulation bath temperature on structure and performance of poly （vinyl butyral） hollow fiber membranes via thermally induced phase separation

Poly （vinyl butyral） （PVB） hollow fiber membranes were fabricated via thermally induced phase separation （TIPS）. The effects of coagulation bath temperature （CBT） on the structure and performance of membranes were investigated in detail. The morphologies of the membranes were studied by scanning electron microscopy （SEM）, the performances of water permeability, rejection, breaking strength and elongation were measured, respectively. The results indicate that all the membranes have the asymmetric morphology and the thickness of the skin layer decreases and the pore size of the outer layer increases with the increase of CBT. The permeability of membranes prepared at air gap 1.0 cm and take-up speed 0.253 m/s increases from 1.047×10-7 to 5.909×10-7 m3/（m2·s-kPa） with the CBT increasing from 20 ℃ to 40℃, and sharply increases to 35.226×10 7 m3/（m2.s.kPa）once the CBT arrives at 50 ℃. While the carbonic ink rejections have no significant decrease, totally exceed 98%, but that of acid-maleic acid copolymer greatly decreases with the increase of CBT. Both the breaking strength and elongation decrease with the increase of CBT.     

介质阻挡放电反应器降解邻二甲苯的特性研究

采用介质阻挡放电(DBD)降解常压下流动态的邻二甲苯模拟废气,系统地考察了放电极值电压,气体的初始质量浓度、停留时间以及相对湿度等工艺参数对邻二甲苯降解的影响,并初步探讨了邻二甲苯的降解产物.实验研究结果表明:在7.0kV的放电极间电压下,邻二甲苯的初始质量浓度为1 500mg/m3,停留时间为9s,其去除率可达到80%以上.降解产物主要为CO2、H2O以及苯甲酸、苯乙酸、苯乙醛等有机物,并且经降解后产物的生物可生化性得到提高,因而为后续的等离子-生物法联合处理VOCs提供了依据.     

铜离子印迹改性壳聚糖海绵的制备及应用研究

以醋酸铜为模板,甲醇、氯仿为溶剂,2-乙烯吡啶、丙烯酰胺为功能单体,乙二醇二甲基丙烯酸酯为交联剂,采用本体聚合法制备铜离子印迹聚合物;然后掺入到壳聚糖海绵的制备中,使壳聚糖海绵对铜离子的吸附率由27．1％提高到72．3％。制备的铜离子印迹改性壳聚糖海绵需要2d达到吸附平衡,吸附-解吸5次后,性能稳定。     

导磁体在汽车零件感应加热中的应用技术

本文简单介绍了导磁体工作的基本原理，并给出在汽车零件大规模生产中所积累的导磁体应用的一些经验，以阐明如何更有效地使用导磁体。     

Oxidation Performance of Fe-Al/WC Composite Coatings Produced by High Velocity Arc Sprayed at 650 ℃

Fe-Al intermetallics with remarkable high-temperatureintensity and excellent erosion,high-temperatureoxidation and sulfuration resistance are potential lowcost high-temperature structural material.ProducingFe-Al/WC composite coating by high velocity arcspraying(HVAS)on structural materials would notonly obviate the problems faced in fabrication of thesealloys into useful shapes,but also allow the effectiveuse of their outstanding high-temperature performance,which might thus promisingly mak…