超声波车辆车轴探头的研制与应用

提出了一种用于检测在役车辆车轴产生疲劳裂纹的超声波方法,设计了中心孔探头与斜角探头一起,完成了对车辆车轴的关键区域探伤。     

低渗透率地层渗透率的确定方法

结合大庆油田外围低渗透率地层的地质特点,根椐渗流理论和岩心分析资料,分析了地层渗透率与孔隙度、组成地层的各种矿物含量以及泥质含量之间的关系,建立了不同矿物组合地层的渗透率计算方程。用本方法计算的和岩心分析的渗透率进行了对比,二者之间具有较好的一致性。     

聚氧乙烯油酸酯的合成与物性

论述了合成聚氧乙烯油酸酯的较佳反应条件,探讨了不同EO加成数的聚氧乙烯油酸脂的表面物性规律。     

~（131）Ⅰ—MIBG比活度对鼠心肌交感神经囊泡内外摄取的影响

研究了两种比活度的１３１Ⅰ－ＭＩＢＧ在正常及利血平抑制后在鼠体内的分布，结果表明：注射后４ｈ，正常鼠心肌对３．２２ＴＢｑ／ｇ的ＭＩＢＧ摄取为９．０８％ＩＤ／ｇ，明显高于对１８．５ＧＢｑ／ｇ的摄取（４．８７％ＩＤ／ｇ）。计算表明，比活度主要影响了鼠心肌交感神经囊泡内摄取，而与囊泡外摄取无关．当ＭＩＢＧ用于心肌显像时，高比活度的ＭＩＢＧ有利于诊断。     

压差式漏率测试仪的实验研究

将薄膜电容真空计的测量室接于被测密闭容器，静态真空室接于一个比较容器，即组成一台压差式漏率测试仪。首先使两容器压力平衡，真空计读数为零。当被测容器存在漏孔时，真空计薄膜两侧形成压差，真空计指示读数，继而计算出该容器的漏率。应用商品真空计在抽真空测试时，检测的最小可测漏率达10－4～10-5Pa·L／s；而在充压测试时，因受气体温度变化的影响，灵敏度会降低几个量级。该仪器有可能具备寻找漏孔位置和确定漏孔漏率的功能。     

Deformation and fracture of glass bead/ CTBN-rubber/epoxy composites

Carboxyl-terminated butadiene-acrylonitrile-rubber decreases modulus and yield stress of the studied epoxy but increases fracture toughness. The addition of glass bead compensates for the loss in modulus but has little effect on yield stress. However, it significantly contributes to the fracture toughness by providing additional mechanisms for toughening of both the unmodified and rubber-modified epoxy. For the toughened epoxies studied, fracture surfaces gave only limited information on fracture mechanisms since significant energy absorption also occurs in the material below the fracture surface. Suggestions for suitable material compositions for fiber composite matrices are given.     

场顺序彩色显示器

荫罩CRT受自身结构的限制,要进一步改进其分辨率就有很大的困难。近年已研制成一种获得彩色图像的颇有吸引力的替代品,即场顺序彩色显示器。它由单色CRT和液晶电子色闸组成,称之为LC/CRT系统。液晶电子色闸由液晶π盒及其连用的偏振片组成,可看成是老式机械彩色轮那样的一种电控色带带通滤色片。本文描述了液晶电子色闸的功能及其工作优点,讨论了其可能结构与显示特性。     

An efficient technique for detecting catastrophic convolutional codes

Catastrophic convolutional codes (CC) cause an infinite number of decoded data bit errors when decoding a finite number of code symbols. A CC displays a catastrophic error propagation if the generating polynomials have a common factor. An efficient algorithm for polynomial factorization in GF(2^m) is used for detecting catastrophic CC for any rate n/m and constraint length k. A general formula is derived to calculate the number of catastrophic codes in any (m, n, k) CC.     

New concept for applying edge line phase-shifting masks to arbitrary mask layouts

This paper explains the principle of a method which avoids printing of phantom resist lines due to undesired intensity minima appearing on Cr-less edge line phase-shifting masks. The method combines principles of grey-tone lithography and attenuated phase-shifting masks to give, what we call, a Cr-Less Attenuated Phase-shifting mask (CLAP). Rules for generating a CLAP design and a paradigm setup of a CLAP mask are presented. The capabilities and possible limitations of the CLAP method based on simulated results for a standard wafer stepper setup using the SOLID lithography simulator are being assessed.     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.