调整水量法(代用法)测定水泥标准稠度用水量方法的改进

结合兰州市的水泥标准稠度用水量方法测定 (代用法 )的实例 ,分析代用法测定标准稠度用水量的缺点 ,并对此方法提出了一些改进措施     

Two-dimensional symmetric multimode interferences in silicon square waveguides

Symmetric interference in two-dimensional multimode silicon waveguides is experimentally investigated. For a 100/spl times/100 /spl mu/m/sup 2/ cross section, 2700-/spl mu/m-long waveguide fabricated on silicon-on-insulator substrate, an 8/spl times/8 matrix of replicated images with high contrast ratio is demonstrated for 1530-1570 nm wavelength range. Symmetric interference results in reduced device length, and the actual device length is consistent with the theoretical expectation. The device also exhibits stable imaging in terms of good loss uniformity, and low wavelength and polarization dependencies among the replicated images.     

Synthesis of TiO<Subscript>2</Subscript> Hybrid Molecular Imprinted Polymer for Ethofumesate Linked by Silane Coupling Agent

TiO₂ hybrid molecular imprinted polymer (MIP) for ethofumesate using methacrylic acid (MAA) as the functional monomer and silane coupling agent 3-(trimethoxysilyl) propylmethacrylate (KH570) as organic–inorganic connective bridge was synthesized via photo-excitation method. Hydrogen bond was proved to act between MAA and ethofumesate for pre- and post-polymerization binding properties as testified by UV spectrometric method. KH570 modified TiO₂ nanoparticles were prepared via sonochemical reaction, which can accelerate hydrolysis, increase collision chance for the reactive system and improve the dispersion of the nanoparticles. Scanning electron microscope (SEM), transmission electron microscope (TEM), binding and the adsorption kinetics experiments as well as thermogravimetric analysis (TGA) were employed for characterization. The results indicated that the hybrid MIP revealed a larger surface area and more ordered imprinting cavities with improved thermal stability compared to organic-only MIP. Furthermore, faster adsorption kinetics and enhancive adsorption capacity were achieved, which made it promising in chemical sensor applications.     

Growth of highly orientated strontium barium niobate thin films on Si substrates through the sol–gel process using a K: SBN template layer

We report the growth of highly C-axis orientation of Sr _x Ba_1−x Nb₂O₆ (SBN) thin films on p-type (100) Si substrates by using a potassium-substituted SBN template layer with the sol–gel method. The crystallization of SBN thin films was found closely related to the potassium ion doping concentration and the postannealing temperature of the K-SBN template layer. Secondary ion mass spectrometry analysis showed that potassium elements were accumulated at the interface of the template layer and silicon substrate. SBN films postannealed at 750 °C with K-SBN template layer has a smaller full width at half maximum of X-ray rocking curve of 2.45° than that of 5.40° for the pure SBN films. By introducing a template layer, the surface morphologies of SBN films fabricated on silicon substrate were greatly improved.     

Formation mechanism of 21R AlN-polytypoids in aluminothermic reduction and nitridation process

Synthesis of 21R AlN polytypoids was investigated using Al and ultrafine SiO₂ powder in a flowing nitrogen atmosphere by means of thermal gravity (TG), differential scanning calorimeter (DSC), X-ray diffractometer (XRD) and scanning electronic microscope (SEM) linked with energy dispersive spectrometer (EDS). The results showed that the formation mechanism of AlN polytypoids was different from that in reaction sintering process using Si₃N₄, AlN, Al₂O₃ and other sintering additive as raw materials. It was suggested that firstly Al reduce SiO₂ into Si and is also nitrided into AlN, then AlN, Al₂O₃ and SiO₂ dissolve into silicon liquid until the AlN polytypoids precipitate in saturated liquid in a flowing nitrogen atmosphere at lower than 1700 °C.     

蓝牙技术及应用简析

蓝牙（Bluetooth）技术是一种短距离无线电技术,利用“蓝牙”技术,能够有效使数据传输变得更加迅速高效。本文主要介绍蓝牙的关键技术及其未来的发展趋势。     

新型刮刀钻头的设计及现场试验研究

在理论分析的基础上，综合PDC钻头和刮刀钻头的优点，设计了一种新型的刮刀钻头，并进行了现场试验。现场试验结果表明，该钻头运转平稳，采用低钻压、高转速，钻进速度快，井眼规则通畅，有较明显的防斜作用，该种钻头的推广应用对提高钻井工程的整体效益具有十分重要的意义。     

完善科技评价办法 提高科技创新能力

科技评价工作是科技管理工作的重要组成部分,是推动国家科技事业持续健康发展、促进科技资源优化配置、提高科技管理水平的重要手段,也是了解科技发展动态、加快科技直接转化为现实生产力的主要措施。根据国家建材工业局建材规划字[2001]3号文《关于转交建材行业科技成果鉴定管     

工程钻机在沙卵石地区的物探钻井

川西平原属沉积平原，不到2m厚的表土下面全是沙卵石，沙卯石厚度达二、三十米。地面覆盖农田，沟垄纵横，限制了车载钻机的进入。以往地震勘探多采取浅井组合方式激发，所获得的地震资料能量差、面波强，对农田破坏面积大。若使用SH30—2A型轻便工程钻机，配上自制的冲击管，采取冲击钻进，从管中下药柱的方式，可实现沙卵石地区的深井激发，提高资料采集质量，且效率高、成本低。     

Aging response of the young’s modulus and mechanical properties of Ti-29Nb-13Ta-4.6Zr for biomedical applications

Alloys for implant devices require improved strength but a reduced Young’s modulus, in order to become mechanically more compatible with adjacent bone tissues. In this study, a new metastable β-type titanium alloy, Ti-29Nb-13Ta-4.6Zr (wt pct), was subjected to aging treatment to produce different microstructures, and the resulting mechanical properties, including the Young’s modulus, were measured. The Young’s modulus of this alloy is found to be sensitive to microstructures generated by various heat treatments. For microstructures varying from (α + β) to (α + β + ω) and (β + ω), the Young’s modulus increases with an accompanying increase in tensile strength and hardness, but decreases in ductility. The (β + ω) microstructure has a low strength, high modulus, and poor ductility and cannot be used for biomedical applications. For an (α + β) microstructure, the volume fraction of the phases is shown to be the main factor that determines the mechanical properties.