马尔可夫跳变线性系统最优控制的研究现状与进展

马尔可夫跳变线性系统（MJLS）是一种具有多个模态的随机系统，系统在各个模态之间的跳变转移由一组马尔可夫链来决定。MJLS模型因其在表示过程中可以产生突变而更能精确的描述实际工程应用中的系统。近年来，MJLS的最优控制问题成为了研究的热点，动态规划、极大值原理以及线性矩阵不等式等成为了解决此类问题的主流方法。本文对MJLS最优控制领域的研究现状进行了综述。分别对一般情况下、带有噪声的情况下、带有时滞的情况下以及某些特定情况下的MLJS最优控制问题的国内外研究现状进行论述。最后进行了总结并提出MJLS最优控制领域未来值得关注的研究方向。     

用于疏浚工程泥浆密度测量的电阻层析成像技术

江河湖海疏浚工程对于拓展和保障航运安全、促进生态恢复、维护/改善远海岛礁环境具有不可或缺的作用.目前,在绞吸和耙吸疏浚船上,多采用射线密度计及电磁流量计对输泥密度、产量等进行在线计量,并作为实现疏浚系统自动控制的重要参量.由于射线密度计潜在的人员健康、公共安全和环保风险,在一些国家和地区已建立了放射源的有序退出机制.电阻层析成像使用安装于管壁的电极阵列获得管道内流体的电导率分布,进而推导出管道内的泥浆密度,具有无辐射、全场测量及实时可视化的优点.电阻层析成像测量系统经过特殊设计,可适应从内陆淡水到海水的巨大电导率变化.初步测试表明,电阻层析成像测量数据与射线密度计具有良好一致性,具备了作为在线泥浆密度测量的可行性.此外,ERT可提供实时的流动成像,对于提高对疏浚管道监测能力和降低堵管概率具有重要意义.     

聚氨酯分散剂在液体靛蓝制备中的应用

采用异佛尔酮二异氰酸酯(IPDI)、聚乙二醇200、400、600、800(PEG200、PEG400、PEG600、PEG800)、2,2-二羟甲基丙酸(DMPA)、1-苯基-1,2-乙二醇、中和剂三乙胺(TEA)、甲乙酮肟等为原料,制备了一种阴离子聚氨酯分散剂.通过FTIR、GPC、TG表征了分散剂的结构与性能.利用自制的分散剂采用研磨法制备了液体靛蓝分散液,以液体靛蓝分散液粒径、离心稳定性、储存稳定性为指标,探讨了分散剂链长、用量对分散液性能的影响.结果表明,研磨1 h后,以PEG400为软段合成的聚氨酯分散剂用量为染料质量的60％时制备的液体靛蓝粒径为277.1 nm,1000 r/min离心稳定性达到93.98％,3000 r/min离心稳定性为51.13％,常温放置7 d后粒径变化在20 nm以内,染色后织物的颜色深度(K/S)为10左右,约是粉状靛蓝染色K/S的2倍,染色织物的颜色性能并未改变,SEM显示分散体颗粒大小分布均匀,与分散剂甲基萘磺酸钠的甲醛缩合物(MF)和木质素85A相比,其分散体系稳定性差别不大.     

文献计量视角下健康人力资本研究动态分析

通过文献计量方法从样本选取、研究动态分析、主题分布三方面对健康人力资本发展现状及热点问题进行总结.研究结果表明,自2004年开始该领域所属学科种类和期刊源日益丰富,并形成合著度较高的核心作者群体,健康人力资本研究成为人力资本领域的研究热点,健康人力资本与经济增长或收入的关系、健康人力资本指标体系的构建和居民健康人力资本收入效应的测算等问题都成为当前和未来的研究重点.     

3-三氟甲基-5,6,7,8-四氢-1,2,4-三唑[4,3-α]吡嗪盐酸盐的合成

乙二胺与氯乙酸乙酯经取代、环合反应制得2-哌嗪酮,2-哌嗪酮与Boc酸酐进行氨基保护反应后,再与五硫化二磷进行硫代反应制得4-(N-叔丁氧羰基)-2-哌嗪硫酮,其与三氟乙酰肼经取代、环合、脱叔丁氧羰基成盐,得标题化合物,总收率为45.7%(以氯乙酸乙酯计)。为磷酸西他列汀中间体的工业化生产提供了一条较理想的工艺路线。     

Transesterification of Palm-based Methyl Palmitate into Esteramine Catalyzed by Calcium Oxide Catalyst

The technology for transesterification reactions between methyl esters and alcohols is well established by using classical homogeneous alkaline catalysts, which provide high conversion of methyl esters to specialty or nonindigenous esters. However, in certain products where the purity of the esters is of concern, the removal of homogeneous catalysts after the completion of the reaction is a challenge in terms of production cost and water footprint. Therefore, a study to investigate the potential of heterogeneous catalysts was conducted on reactions between methyl palmitate and triethanolamine. The degree of basicity and active surface area of calcium oxide (CaO), zinc oxide (ZnO), and magnesium oxide (MgO) were first characterized by using temperature-programmed desorption (TPD-CO₂) and Brunauere–Emmett–Teller (BET), respectively. Among the metal oxides investigated, the CaO catalyst showed the best catalytic activity toward the transesterification process as it gave the highest conversion of methyl palmitate and yielded fatty esteramine compositions similar to the conventional homogeneous catalyst. The optimum transesterification condition by using the CaO catalyst utilized a lower vacuum system of approximately 200 mbar, which could minimize a considerable amount of energy consumption. Furthermore, low CaO dosage of 0.1% was able to give a conversion of 94.5% methyl ester and formed esteramine at 170 °C for 2 h. Therefore, the production of esterquats from esteramine may become more economically feasible through the methyl ester route by using the CaO catalyst, which can be recycled three times.     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.