刚柔结合的充电机械臂设计

针对大型运输设备上的电池充电补给任务,设计了一款刚柔结合充电机械臂.针对机械臂的柔性部分和刚性部分分别分析了关节、任务、驱动空间之间的运动映射关系,给出了两级柔性臂的解耦运动学算法,使用蒙特卡洛方法求解了机械臂的工作空间,验证了机械臂设计的合理性,并用Adams软件进行动力学仿真分析,校核了设备选型的安全性.     

用于疏浚工程泥浆密度测量的电阻层析成像技术

江河湖海疏浚工程对于拓展和保障航运安全、促进生态恢复、维护/改善远海岛礁环境具有不可或缺的作用.目前,在绞吸和耙吸疏浚船上,多采用射线密度计及电磁流量计对输泥密度、产量等进行在线计量,并作为实现疏浚系统自动控制的重要参量.由于射线密度计潜在的人员健康、公共安全和环保风险,在一些国家和地区已建立了放射源的有序退出机制.电阻层析成像使用安装于管壁的电极阵列获得管道内流体的电导率分布,进而推导出管道内的泥浆密度,具有无辐射、全场测量及实时可视化的优点.电阻层析成像测量系统经过特殊设计,可适应从内陆淡水到海水的巨大电导率变化.初步测试表明,电阻层析成像测量数据与射线密度计具有良好一致性,具备了作为在线泥浆密度测量的可行性.此外,ERT可提供实时的流动成像,对于提高对疏浚管道监测能力和降低堵管概率具有重要意义.     

可重构机器人模块间装配误差识别方法研究

基于对可重构机器人配对接口间位姿误差的分析划分,研制模块间装配误差在线测量识别接口,建立配对接口位姿误差与接口几何结构偏差之间的关系模型,进而建立配对接口位姿误差与配对接口内部测距传感器测量值之间的映射关系模型,提出一种基于内部测距传感器位移量的模块间装配误差在线识别、补偿方法.为验证方法的正确性,研制单关节?连杆试验平台.试验结果表明装配误差经在线识别、补偿后,连杆末端的位置误差平均值减少7倍多.     

基于粒子群优化和支持向量机的花粉浓度预测模型

为了提高花粉浓度预报的准确率，解决现有花粉浓度预报准确率不高的问题，提出了一种基于粒子群优化（PSO）算法和支持向量机（SVM）的花粉浓度预报模型。首先，综合考虑气温、气温日较差、相对湿度、降水量、风力、日照时数等多种气象要素，选择与花粉浓度相关性较强的气象要素构成特征向量；其次，利用特征向量与花粉浓度数据建立SVM预测模型，并使用PSO算法找出最优参数；然后利用最优参数优化花粉浓度预测模型；最后，使用优化后的模型对花粉未来24 h浓度进行预测，并与未优化的SVM、多元线性回归法（MLR）、反向神经网络（BPNN）作对比。此外使用优化后的模型对某市南郊观象台和密云两个站点进行逐日花粉浓度预测。实验结果表明，相比其他预报方法，所提方法能有效提高花粉浓度未来24 h预测精度，并具有较高的泛化能力。     

一种抗运动干扰的实时心率提取方法

针对基于容积脉搏波（PPG）提取运动心率时，传统心率提取算法由于运动噪声干扰使测量结果误差大、实时性不好的问题，提出一种抗运动干扰的实时心率提取方法。该方法通过实时小波去噪，同时结合三轴加速度信号（ACC）对运动进行分类训练，计算各运动状态心率增益，对实时心率值进行补偿。实验结果表明，通过与同时采集的ECG信号计算出的实时心率进行对比，绝对误差率仅为1.2%左右。相比传统心率提取算法，该算法具有抗干扰性强，实时准确的特点。     

Modeling Impact of ROADM Intra-Node Add/Drop Contention on a Single Node Lightpath Blocking Performance

We propose an analytical model to evaluate the lightpath blocking performance for a single ROADM node with intra-node add/drop contention,in which the number of lightpaths that can be added/dropped with the same wavelength is limited by the add/drop contention factor.Different models of traffic load per nodal degree are considered to validate the effectiveness of the analytical model.The simulation results show that the proposed analytical model is effective in predicting the performance for different values of add/drop contention factor C and for variable offered loads at the node.The add/drop contention factor shows an important impact on the lightpath blocking performance and properly raising the contention factor can significantly improve the lightpath blocking performance.When the add/drop contention factor C exceeds a certain level,the performance of a ROADM with intra-node contention is close to that of a contentionless ROADM.     

Effect of an abrupt change in pulling rate on microstructures of directionally solidified Al2O3-Er3Al5O12 eutectic and off-eutectic composite ceramics

Directionally solidified microstructures of Al₂O₃-Er₃Al₅O₁₂ eutectic and off-eutectic in situ composite ceramics were explored under abrupt-change pulling rate conditions. Corresponding temperature distributions and interface locations were studied. In eutectic composition, fluctuation of eutectic spacing occurred when the pulling rate increased abruptly. A gradually increase or abrupt increase in eutectic spacing was observed when the pulling rate decreased abruptly. In hypoeutectic and hypereutectic compositions, formation of the primary phases were suppressed when the pulling rate increased abruptly from 10?µm/s to 100?µm/s, while primary phases precipitated when the pulling rate decreased abruptly from 100?µm/s to 10?µm/s. The interface altitude decreased after the pulling rate increased abruptly, but increased after the pulling rate decreased abruptly. The liquid composition restriction (around the eutectic composition) at the eutectic interface plays an important role in the suppression of the primary dendrite and coupled eutectic oxides can be obtained in off-eutectic compositions even under higher solidification rate conditions.     

A computer aided design method for car form and its application based on shape parameters

In the early design stage, automotive modeling should both meet the requirements of aesthetics and engineering. Therefore, a vehicle CAD (computer aided design) model that can be easily adjusted by feedbacks is necessary. Based on CE-Bézier surface, this paper presents a set of algorithms for parametric segmentation and fairing surface generation in a car model. This model is defined by a simplified automotive template and relevant control points, shape parameters and segmentation parameters, which can be modified to alter the car form efficiently. With this model and the corresponding adjustment method, more than fifty various vehicle models are established in this research according to different parameters. And two methods for calculating similarity index between car models are constructed, which are suitable for brand design trend analysis and modelling design decisionmaking.     

Alloy optimisation of bainitic steel for large plastic mould

Based on the phase transformation theories, especially the T₀ concept of bainite transformation, alloy optimisation of bainitic steel with carbides has been carried out aiming at the produce of plastic mould with large cross-section. The effect of manganese and silicon on proeutectoid ferrite and bainite transformation is explored by dilatometric analysis, XRD and different microscopy techniques. The results show that after the alloy optimisation, the transformation of proeutectoid ferrite is suppressed and when the cooling rate is lower than 0·1°C?s^??1, the new lower bainite transformation appears by decreasing carbon capacity of austenite and promoting carbide precipitation. Industrial production proves that the optimised alloy SDP1 can meet the demand for the plastic mould with the thickness of 1050?mm.