The correlation of texture and magnetic properties in Co-Cr films

This investigation focuses on the correlation between the crystallographic orientation of grains with respect to magnetic properties in Co-Cr films. Based on a distribution measured for the (0002) crystallographic pole densities, modified formulae describing the texture were used to calculate the coercivity Hc, the squareness ratio Rs (Mr⊥/TMs) and the anisotropy field Ha for Co-Cr films. In general, calculated values for the coercive force He agreed well with the measured values. The calculated Rs⊥. values were much larger than the measured ones, however, indicating that the influence of the demagnetizing field and the magnetostriction on the orientation of the magnetization cannot be neglected. On leave from Institute of Computing Technology, Academia Sinica, P.O.Box 2704-6, Beijing, P.R. China.     

A hybrid spreading/despreading function with good SNR performancefor band-limited DS-CDMA

Code-division multiple-access (CDMA) implemented with direct-sequence spread spectrum (DS/SS) signaling is a promising multiplexing technique for cellular telecommunications services. The efficiency of a direct-sequence spread-spectrum code-division multiple-access (DS-CDMA) system depends heavily on the shape of the spectrum of the spread signal. Maximum efficiency is obtained with an ideal brick-wall bandpass spectrum. There are two approaches toward achieving such a spectrum. One is to use a simple spreader that produces a broad spectrum and then follow it with a precise, high order filter to band limit the spectrum. A second approach, which is the approach taken in this paper, is to use a spreader that produces a spectrum close to the ideal spectrum and then employ a simple filter to control the out-of-band power. The proposed spreader/despreader is based on a simple hybrid function and can be easily implemented. An analysis provides a compact expression for the signal-to-noise ratio (SNR) of a RAKE receiver. The expression includes the effects of baseband, intermediate frequency (IF) and RF filtering as well as the effects of the spectral densities of the spreading/despreading functions. The analysis shows that the proposed spreader/despreader yields superior performance over a conventional pseudo noise (PN) spreading/despreading mechanism     

可配置非幂方分频器的全新设计方法

本文采用基于计数空间完全划分和周期插入控制计数过程方法设计了非幂方分频器,采用这种全新思路设计的非幂方分频器分频范围很宽,分频输出对后续分频支持好,非常适用于通讯接口中的波特率时钟设计.此外,这种设计思路对系统定时电路和节拍控制电路设计也有一定的借鉴意义.     

Automatic fault detection, isolation, and recovery in transparentall-optical networks

Network fault identification is an important network management function, which is closely related to fault management and has an impact on other network management functions such as configuration management, and performance management. This paper investigates fault surveillance and fault identification mechanisms for a transparent optical network in which data travels optically from the source node to the destination node without going through any optical-to-electrical (O/E) or electrical-to-optical (E/O) conversion. Mechanisms and algorithms are proposed to detect and isolate faults such as fiber cuts, laser, receiver, or router failures. These mechanisms allow nonintrusive device monitoring without requiring any prior knowledge of the actual protocols being used in the data transmission     

埋地管道涂层检测技术现状

文章对各种埋地管道涂层检测技术进行了综述,并指出了各种技术的优缺点及应用前景.     

深亚微米MOSFET衬底电流的模拟与分析

利用器件模拟手段对深亚微米ＭＯＳＦＥＴ的衬底电流进行了研究和分析，给出了有效的道长度，栅氧厚度，源漏结深，衬底掺杂浓度以及电源电压对深亚微米ＭＯＳＦＥＴ衬底电流的影响，发现电源电压对深亚微米ＭＯＳＦＥＴ的衬底电流有着强烈的影响，热载流子效应随电源电压的降低而迅速减小，当电源电压降低到一定程度时，热载流子效应不再成为影响深亚微米ＭＯＳ电路可靠性的主要问题。     

一种多晶硅高温压力传感器

制作压力传感器时，在二氧化硅层上淀积多晶硅膜，既可利用优良的机械特性，又可保证压敏电阻与衬底间具有良好的绝缘性，由此可大大提高器件的温度特性。介绍了一种多晶硅压力传感器的原理和设计。实验结果表明，这类传感器具有灵敏度好，精度高等特点，电路工作范围为０－２５０℃，且具有良好的温度稳定性。     

大型现浇钢筋混凝土U型渡槽施工技术

禹门口提水工程干渠上的十几座大型钢筋混凝土渡槽采用现浇混凝土施工方案。经过十几座渡槽的施工及通水检验，证明现浇施工技术与工艺已经成熟。本文就施工中遇到的高大排架外形与垂直度控制、槽身模板制做与固定、模具的空中支撑、运输与入仓办法等做以简单介绍。     

移动式宽频带高产额中子发生器

多用途中子发生器有着广阔的市场和应用领域 ,文章对移动式宽频带高产额中子发生器 ,在设计制造过程中所涉及到的技术难点 :绝缘尺寸小、频率适应范围宽、为中子管提供靶压的高压负载特性好等作了技术分析 ,使多用途中子发生器在更广阔的范围内应用 ,提供了广阔前景。     

单片机仿真系统

本文讨论单片机离线仿真系统的设计方法，其关键技术是：单片机硬件系统（ＲＡＭＲＥＧＩＳＴＥＲＳ）仿真，指令系统仿真，中断系统仿真，应用系统硬件仿真。