Cd-ZSM-5沸石催化剂的制备、表征和芳构化催化性能

采用离子交换、浸渍和混合三种方法制备镉改性ZSM-5沸石催化剂,考察了改性方法和镉含量对催化剂的表面酸性和Cd状态以及芳构化性能的影响。结果表明,加入镉降低了B酸性,Cd~(2+)与沸石结合形成了L_(1612)酸中心,其生成量取决于改性方法和Cd含量,并与芳构化活性提高有直接关系。     

Clinical study in epidural injection with lappaconitine compound for post-operative analgesia

In this study, the effect and side-effect of epidural injection with lappaconitine compound for post-operative analgesia was observed. One hundred and twenty patients were randomly divided into 4 groups. Lappaconitine compound (LB) consisted of 12 mg of lappaconitine and 22.5 mg of bupivacaine, was given to group A (the group of observation), and lappaconitine 12 mg, bupivacaine 22.5 mg and morphine 2 mg to group B, C and D respectively for control. All were given by epidural injection with single blind method during post-operative pain of incision operation. Result showed that the initiating of analgesia was quicker in group A and C than that in group B and D, and the efficacy was group D > A > C > B. There was significant difference between group A and B in the above two parameters, P < 0.01 and P < 0.05. The analgisia maintenence time of single injection was D > A > B > C, that of group D was significantly longer than that of group A (P < 0.01). It indicated that the epidural injection with LB was more rapid and potent than that with lappaconitine alone in post-operative analgesia, and the former had no side-effect, it was safer than morphine.     

离子注入中污染的产生及防护

本文概述了离子注入过程中污染产生的原因和防止污染的措施，特别强调了对微粒污染和金属污染的防护以满足ＵＬＳＩ加工对离子注入的要求。     

δ－Al_2O_3纤维／Al－12Si复合材料室温拉伸强度分析

对δ－Ａｌ２Ｏ３纤维／Ａｌ－１２Ｓｉ复合材料室温拉伸强度的分析表明，在实验条件下该复合材料存在δ－Ａｌ２Ｏ３纤维的最小体积分数Ｖｍｉｎ和临界体积分数Ｖｃｒｉｔ，并求出其基体强度σ＇ｍ和室温强度σｃ－δ－Ａｌ２Ｏ３纤维体积分数Ｖｆ直线方程及纤维的临界长度ｌｃ和复合材料的剪切应力τｉ．确定复合材料的ＲＯＭ预测曲线，应首先判断σ＇ｍ是否等于未增强合金的强度σｕｍ才能得出正确的结论     

Improved Yen-Joye's authenticated multiple-key agreement protocol

An authenticated multiple-key agreement protocol is proposed. The protocol is not only secure against the unknown-key attack but also more efficient than other protocols.     

Fabrication of 1.55 μm VCSELs on Si using metallic bonding

Using AuGeNiCr multilayered metals as the wafer bonding medium, long-wavelength GaInAsP/InP vertical cavity surface emitting lasers employing Al-oxide/Si as the upper and lower distributed Bragg reflectors were fabricated on Si substrate with the bonding interface formed outside the vertical cavity surface emitting laser cavity. Laser emission at 1.545 μm was measured under pulsed operations near room temperature. The low-temperature metallic bonding process demonstrates a great potential in device fabrication     

LDD方法在提高电路工作电压中的应用研究

研究了利用轻掺杂漏结构来制作高电源电压器件的工艺方法。分析了ＬＤＤ结构参数对器件击穿特性的影响，并结合实验结果对Ｎ＾－区的注入剂量，长度及引入的串联电阻进行了优化设计。     

NMOS器件两次沟道注入杂质分布和阈电压计算

分别考虑了深浅两次沟道区注入杂质在氧化扩散过程中对表面浓度的贡献。对两次注入杂质的扩散分别提取了扩散系数的氧化增强系数、氧化衰减系数和有效杂地系数，给出了表面浓度与工艺参数之间的模拟关系式，以峰值浓度为强反型条件计算了开启电压，文章还给出了开启电压、氧化条件、不同注入组合之间的关系式。     

Coplanar waveguide-fed uniplanar bow-tie antenna

The design of coplanar waveguide (CPW)-fed bow-tie antenna for the 2.4-GHz ISM band is described. A coplanar waveguide-to-coplanar strips (CPW-to-CPS) balun is used to obtain the balanced feed line for the printed bow-tie. An analysis method based on the mixed potential integral equation method is used to characterize the input characteristics of the bow-tie antenna. The numerical results obtained are in good agreement with the experimental data. Through experiments with bow-tie antennas of various extended angles, the bow-tie antenna with a 90° extended angle exhibits the widest bandwidth in the desired frequency band which has a bandwidth of 17% for a VSWR <1.5:1