面向草莓抓取的气动四叶片软体抓手研制

农林业中果蔬的自动化采摘需求日趋强烈,末端抓手是实现无损采摘的关键。传统的末端抓手以刚性结构居多,现有的各种柔性抓手也存在抓取力不足、包覆性不佳等缺点。本文以草莓的无损采摘为研究对象,提出将草莓外部轮廓曲线作为设计曲线,设计了一种新型气动四叶片软体抓手。首先,对软体抓手的结构做仿真优化,提出一种安全地附着在目标物表面的设想。然后,在进行草莓表面的最小破坏应力试验的基础上,测试了软体抓手的末端力,验证了其实现无损抓取的可行性。再次,利用动态捕捉技术,研究了软体抓手叶面的弯曲变形规律。最后,选择使用弧线型气体通道的软体抓手进行了草莓抓取测试,结果证明了气动四叶片软体抓手可以实现草莓的无损抓取,抓取成功率达90%,破损率为2%,表明所研制的四叶片软体抓手用于草莓抓取时具有良好的稳定性和实用性,可用于草莓采摘的末端执行器。本研究也可为其他易损果蔬的采摘技术提供理论基础和技术支撑。     

Low-temperature synthesis of SiC nanowires with Ni catalyst

SiC nano wires were fabricated on the silicon substrate dipped with a layer of Ni catalyst at 900 ℃ by gas pressure annealing processing. The morphologies and crystal structures were determined by scanning electron microscopy(SEM), transmission electron microscopy(TEM)and X-ray diffraction(XRD). The results show that the assynthesized nanowires are β-SiC single crystalline with diameter range of 50-100 nm, and length of tens of micron by directly annealing at 900 ℃. The SiC nano wires grow along the [111] direction with highly uniform morphology. And the possible growth mechanism of SiC nano wires is proposed.The present work provides an efficient strategy for the production of high-quality SiC nano wires.     

Evaluation of bismuth doped La2-xBixNiO4+δ (x = 0, 0.02 and 0.04) as cathode materials for solid oxide fuel cells

Bismuth doped La_2-xBi_xNiO_4+δ (x = 0, 0.02 and 0.04) oxides are investigated as SOFC cathodes. The effects of Bi doping on the phase structure, thermal expansion, electrical conduction behavior as well as electrochemical performance are studied. All the samples exist as a tetragonal Ruddlesden-Popper structure. Bi-doped LBNO-0.02 and LBNO-0.04 have good chemical and thermal compatibility with LSGM electrolyte. The average TEC over 20–900°С was 13.4 × 10^?6 and 14.2 × 10^?6 K^?1 for LBNO-0.02 and LBNO-0.04, respectively. The electrical conductivity was decreasing with the rise of Bi doping content. EIS measurement indicates Bi doping can decrease the ASR values. At 750 °C, the obtained ASR for LBNO-0.04 is 0.18 Ωcm², which is 56% lower than that of the sample without Bi doping, suggesting Bi doping is beneficial to the electrochemical catalytic activity of LBNO cathodes.     

Synthesis of Diamond@SiO2@Ag composite materials for high SERS effect

Among various carbon materials, diamond stands out due to excellent physical and chemical properties. In this work, we designed Dia@SiO₂@Ag composites combining diamond micropowder and Ag nanoparticles by a simple chemical method and obtained stable substrate for surface enhanced Raman scattering (SERS) owing to its high surface-to-volume ratio, low density, as well as close bond between diamond and Ag. As-prepared Dia@SiO₂@Ag presented high activity to detect crystal violet and rhodamine 6G molecules, which was demonstrated by significantly enhanced SERS spectra and high enhancement factor values (10⁸-10⁹). Moreover, Dia@SiO₂@Ag also showed desired sensitivity, which was investigated by detection limit. Therefore, our study provided more theoretical support and broadened the functional applications of diamond, particularly in Raman detection.     

Combining molybdenum carbide with ceria overlayers to boost Mo/CeO2 catalyzed ammonia synthesis

The design of an efficient non-noble metal catalyst is of burgeoning interest for ammonia synthesis. Herein, we report a Mo₂C/CeO₂ catalyst that is superior in ammonia synthesis activity. In this catalyst, molybdenum carbide coexisted with the ceria overlayers which is from the ceria support as the strong metal–support interaction. There is a high proportion of low-valent Mo species, as well as high concentration of Ce³⁺ and surface oxygen species. The presence of Mo₂C and CeO₂ overlayers not only leads to enhancement of hydrogen and nitrogen adsorption, but also facilitates the desorption and exchange of adsorbed species with the gaseous reagents. Compared with the Mo/CeO₂ catalyst prepared without carbonization, the Mo₂C/CeO₂ catalyst is more than sevenfold higher in ammonia synthesis rate. This work not only presents an explicit example of designing Mo-based catalyst that is highly efficient for ammonia synthesis by tuning the adsorption and desorption properties of the reactant gases, but opens a perspective for other elements in ammonia synthesis.     

Data sharing mechanism of various mineral resources based on blockchain

Basins with various mineral resources coexisting and enriching often occupy an important strategic position. The exploration of various mineral resources is repetitive at present due to unshared data and imperfect management mechanism. This situation greatly increases the cost of energy exploitation in the country. Traditional data-sharing mode has several disadvantages, such as high cost, difficulty in confirming the right of data, and lack of incentive mechanism, which make achieving real data sharing difficult. In this paper, we propose a data-sharing mechanism based on blockchain and provide implementation suggestions and technical key points. Compared with traditional data-sharing methods, the proposed data-sharing mechanism can realize data sharing, ensure data quality, and protect intellectual property. Moreover, key points in the construction are stated in the case study section to verify the feasibility of the data-sharing system based on blockchain proposed in this paper.     

豫西雷门沟钼矿水文地质条件分析及涌水量预测

豫西熊耳山雷门沟钼矿床位于东秦岭多金属成矿带东段,是已探明的超大型斑岩型钼矿,前人研究程度高、地质成果丰硕,但对矿床开采技术条件方面研究较少。本次通过地质调查工程、水文地质试验等方法,从水文地质角度,对雷门沟钼矿床水文地质条件进行研究,填补了该方面的空白,丰富了研究成果；采用水文地质比拟法预测未来矿坑最大排水量2613 m³/d,经实践检验结果较为可靠；总结的采坑排水量预测方法、含水层特点、矿床充水因素以及防治水措施,以期对该区域水文地质工作具有参考价值。     

Preparation and electrochromism of pyrochlore-type tungsten oxide film

Pyrochlore-type WO_3 powder was synthesized via hydrothermal method using aqueous sodium tungstate solution and oxalic acid as raw materials. The as-prepared powder was made into a soliquoid,from which films were made by dip coating process with indium-tin oxide(ITO).The obtained films were characterized by thermogravimetric and differential thermal analysis(TG-DTA), X-ray diffraction(XRD),scanning electron microscopy(SEM),transmission electron microscopy(TEM), cyclic voltammetry(CV), chronoamperometry(CA) and ultravioletvisible(UV-Vis) absorption. Results show that the crystal of the pyrochlore-type WO_3 powder is perfect. When the calcination temperature rises from room temperature to500 ℃,the pyrochlore-type structure first becomes deformed, then it is destroyed and turns into amorphous phase,finally it will completely convert to WO_3 with a monoclinic structure. Electrochemical and optical tests demonstrate that the film calcined at 300 ℃ exhibits the best electrochromic performance and has a coloration efficiency of up to 68.5 cm~2 C~(-1) at 884 nm.     

A novel bio‐based phthalonitrile resin derived from catechin: synthesis and comparison of curing behavior with petroleum‐based counterpart

The development of bio‐based thermosetting resins with good thermal stability can potentially afford sustainable polymers as replacements for petroleum‐based polymers. We report a practical route to a novel catechin‐based phthalonitrile resin precursor (CA‐Ph), which contains free phenolic hydroxyl groups that result in ‘self‐curing’ at elevated temperatures to afford a thermostable polymer. Comparison of the performance of this CA‐Ph resin with that of a conventional petroleum‐based bisphenol A phthalonitrile resin (BPA‐Ph; containing 5 wt% of the curing agent 4,4′‐diaminodiphenylsulfone) revealed that CA‐Ph exhibits a lower melting point and curing temperature. Cured CA‐Ph resin retains 95% of its weight at 520 °C under a nitrogen atmosphere, which compares favorably with results obtained for BPA‐Ph resin that retains 95% of its weight at a lower temperature of 484 °C. Kinetic results indicated that the curing reactions of both CA‐Ph and BPA‐Ph systems follow an autocatalytic mechanism. These results suggest that catechin is a useful bio‐based feedstock for the preparation of self‐curing and thermally stable phthalonitrile resins for advanced technological applications. © 2017 Society of Chemical Industry     

Using electroencephalogram to continuously discriminate feelings of personal thermal comfort between uncomfortably hot and comfortable environments

Thermal comfort is an important factor for the design of buildings. Although it has been well recognized that many physiological parameters are linked to the state of thermal comfort or discomfort of humans, how to use physiological signal to judge the state of thermal comfort has not been well studied. In this paper, the feasibility of continuously determining feelings of personal thermal comfort was discussed by using electroencephalogram (EEG) signals in private space. In the study, 22 subjects were exposed to thermally comfortable and uncomfortably hot environments, and their EEG signals were recorded. Spectral power features of the EEG signals were extracted, and an ensemble learning method using linear discriminant analysis or support vector machine as a sub-classifier was used to build the discriminant model. The results show that an average discriminate accuracy of 87.9% can be obtained within a detection window of 60 seconds. This study indicates that it is feasible to distinguish whether a person feels comfortable or too hot in their private space by multi-channel EEG signals without interruption and suggests possibility for further applications in neuroergonomics.