内循环好氧三相流化床处理造纸中段废水

本实验采用内循环好氧三相流化床处造纸中段废水，经过一段时间的驯化，获得了稳定的出水。CDO去除经保持在65％以上，系统对进水污染负荷的变化具有较大的承受能力。出水Cl^-的浓度有所增加，说明驯化后的微生物可能对有抽氯化物具有一定的降解作用。水气比在1／120至1／140之间可获得最好的COD去除效果。后进行絮凝处理后，出水COD降为60－80mg/L,BODo 50-60/L，色度为100－150CU，挥发性酚的质量浓度小于0．0265mg／L。     

Interfacial segregation of Ti in the brazing of diamond grits onto a steel substrate using a Cu-Sn-Ti brazing alloy

Diamond grits were brazed onto a steel substrate using a prealloyed Cu-10Sn-15Ti (wt pct) brazing alloy at 925 °C and 1050 °C. Due to the relatively high concentration of Ti in the brazing alloy, the braze matrix exhibited a composite structure, composed of β-(Cu,Sn), a Cu-based solid solution, and various intermetallic compounds with different morphologies. The reaction of Ti with diamond yielded a continuous TiC layer on the surfaces of the diamond grits. On top of the TiC growth front, an intermetallic compound, composed of Sn and Ti, nucleated and grew into a randomly interwoven fine lacey structure. An interfacial structure developed as the interwoven fine lacey phase was semicoherently bonded to the TiC layer, with the Cu-based braze matrix filling its interstices. The thickness of such a composite layer was increased linearly with the square root of isothermal holding time at 925 °C, complying with the law of a diffusion-controlled process. However, at 1050 °C, the segregation behavior of Ti and Sn to the interfaces between the TiC layer and the braze matrix diminished, due to the increased solubility of Ti in the Cu-based liquid phase. The enhanced dissolution of Ti in the Cu-based liquid phase at 1050 °C also caused the precipitation of rod-like CuTi with an average diameter of about 0.2 μm during cooling. SnTi₃ was the predominant intermetallic compound and existed in three different forms in the braze matrix. It existed as interconnected grains of large size which either floated to the surface of the braze matrix or grew into faceted grains. It also exhibited a nail-like structure with a mean diameter of about 1 μm for the rod section and a lamellar structure arising from a eutectic reaction during cooling.     

新型高k栅介质材料研究进展

随着半导体技术的不断发展，MOSFET（metal-oxide-semiconductor field effect transistor）的特征尺寸不断缩小，栅介质等效氧化物厚度已小至nm数量级。这时电子的直接隧穿效应将非常显著，将严重影响器件的稳定性和可靠性。因此需要寻找新型高k介质材料，能够在保持和增大栅极电容的同时，使介质层仍保持足够的物理厚度来限制隧穿效应的影响。本文综述了研究高k栅介质材料的意义；MOS栅介质的要求；主要新型高k栅介质材料的最新研究动态；展望了高k介质材料今后发展的主要趋势和需要解决的问题。     

心理因素对分析数据的影响及预防措施

研究了分析人员的心理状态、情绪变化、内在动机等对分析数据的影响,提出了具体的对策和预防措施     

塑料挤出型材车间公用工程设计

鉴于当今人们对塑料门窗需求量的增大，通过对5个塑料挤出型材车间的设计，将其公用工程设计整理成文，总结出塑料挤出型材车间的采暖通风设计，压缩空气系统设计，制冷系统设计的较详尽的方案，以供有关设计技术人员参考。     

吹风气余热回收锅炉在我厂的应用

介绍了吹风气余热回收锅炉在兖矿鲁南化肥厂的应用情况。实践证明，系统运行稳定，取得了良好的经济效益。     

The Synthesis of Sulfated Titanium Oxide Nanotubes

TiO₂ nanotubes can be prepared in gram quantities by treating anatase TiO₂ powder with concentrated NaOH solution. These TiO₂ nanotubes acquired strong acidity after being impregnated with sulfuric acid solution and calcined at 300 °C. The anatase TiO₂ powder used to prepare the nanotube did not catalyze the esterification between cyclohexanol and acetic acid, while sulfated TiO₂ nanotubes were very reactive toward the esterification reaction.     

数字化制模新技术

数字化制模技术是将三维CAD模型直接转化成为铸造用模的新技术。文中介绍了华中科技大学开发的HRP系列数字化制模技术的原理及制模工艺。与传统制模方法相比 ,具有制模速度快、精度高、质量好、价格便宜等优点。文中还以制作轿车制动器卡钳体模样、搅拌叶片模样、蜗壳凸样为例说明了运用数字化制模新技术的优点     

汽车稳定杆组织与疲劳性能研究

对28Mn6钢制造的汽车稳定杆，分别采用整体感应加热－整体淬火、连续感应加热淬火两种不同热处理工艺，并进行了台架疲劳寿命试验，采用光学显微镜和扫描电镜，分析了经两种不同热处理工艺处理的稳定杆的金相组织及其早期疲劳断裂的断口形貌，提出，获得细小的高韧性索氏体组织是保证良好疲劳寿命的关键，稳定杆喷丸表面质量，游离铁素体也是影响疲劳性能的重要因素。     

KZON-50/120空分设备的安装调试及设计改造

在KZON-50/120空分设备的安装调试和试运行过程中,对其机械和电器部分进行了多处改造,克服了原设计中存在的不足之处。改造后,机械和电器性能更加趋于合理,操作简单,便于维护,降低了制气费用,提高了制气纯度和经济效益,保证了空分设备更加安全可靠运行。