负载型固体催化剂在生物柴油制备中的研究现状及应用前景

对生物柴油及其制备方法进行简单介绍，重点综述了负载型固体酸、碱催化剂在生物柴油制备中的研究现状，并指出当前负载型固体催化剂研制中的研究热点，最后对其应用前景了进行展望。     

Global Asymptotical Synchronization of Chaotic Lur'e Systems Using Sampled Data: A Linear Matrix Inequality Approach

Sampled-data feedback control for master-slave synchronization schemes that consist of identical chaotic Lur'e systems is studied. Sufficient conditions for global asymptotic synchronization of such chaotic Lur'e systems are obtained using the free-weighting matrix approach and expressed in terms of linear matrix inequalities (LMIs). With the help of the LMI solvers, the sampled-data feedback control law can easily be obtained to globally asymptotically synchronize Lur'e chaotic systems. The effectiveness of the proposed method is finally illustrated via numerical simulations of chaotic Chua's circuits.     

Tri-Gate Bulk MOSFET Design for CMOS Scaling to the End of the Roadmap

A tri-gate bulk MOSFET design utilizing a low-aspect-ratio channel is proposed to provide an evolutionary pathway for CMOS scaling to the end of the roadmap. 3-D device simulations indicate that this design offers the advantages of a multi-gate FET (reduced variability in performance and improved scalability) together with the advantages of a conventional planar MOSFET (low substrate cost and capability for dynamic threshold-voltage control).     

Automating application software generation

Many approaches have been proposed to enhance software productivity and reliability. These approaches typically fall into three categories: the engineering approach, the formal approach and the knowledge-based approach. But the optimal gain in software productivity cannot be obtained if one relies on only one of these approaches. This paper describes the work in knowledge-based software engineering conducted by the authors for the past 10 years. The final goal of the research is to develop a paradigm for software engineering which integrates the three approaches mentioned above. A knowledge-based tool which can support the whole process of software development is provided in this paper.     

带材位置自动对中系统的工作原理及应用

本文详细介绍了金属带材轧机带材位置自动对中系统的工作原理、电路组成及调试方法。     

Sol-Gel Preparation of LaNiO3 and Its Physical and Chemical Properties

LaNiO3 was synthesized by sol-gel method in which lanthanum nitrate and nickel nitrate were used as start materials and citric acid was used as complex for gel formation.The precursor was dried and subsequently heated at elevated temperature to form the desired product.XRD analysis shows that pure LaNiO3 was synthesized.Electrical conductivity and electrochemical performance of the material were tested.The electrical conductivity decreases from 34.5that there are current peaks in the curve, which is the evidence of the electrochemical activity of LaNiO3.     

Residual stresses and transformation toughening in MoSi2 composites reinforced with partially stabilized zirconia

The results of study of the effects of yttria stabilization (0–6 mol.%) on the room-temperature fracture behavior and toughening mechanisms in zirconia-reinforced MoSi₂ are presented in this paper. Transformation toughening is shown to occur only in composites reinforced with zirconia particles stabilized with 2 mol.% yttria. However, the fracture toughness levels are comparable in the other composites with yttria levels between 0 and 6 mol.%. Toughening in the other composites is attributed to the combined effects of residual stress, microcrack shielding/anti-shielding and/or crack deflection. A rigorous micromechanics-based model is presented for the estimation of residual stress levels in brittle materials reinforced with phases that can transform during cooling or under stress. The model is applied successfully to the rationalization of the observed fracture and toughening phenomena.     

对洪水分级的浅见

洪水的等级划分应考虑流量、水位、防洪能力及灾害等因素,综合这些因素把洪水分成5个等级。1、2级洪水,洪水流量小,水位低,基本无灾;3级洪水,洪水流量较大或水位较高,有一定灾害;4级洪水,为大洪水或高水位,有较大灾害;5级洪水,为特大洪水或高水位,灾情严重。