氯化聚丙烯改性胶粘剂的合成及粘附性能研究

以甲苯为溶剂，过氧化二苯甲酰(BP0)为引发剂，通过自由基聚合，采用甲基丙烯酸羟乙酯(HEMA)和苯乙烯(St)接枝改性氯化聚丙烯(CPP)。研究了不同苯乙烯用量、不同反应温度、不同反应时间、不同引发剂用量对改性氯化聚丙烯胶粘剂粘附性能的影响，得出较佳的工艺条件为反应温度90℃，反应时问2h，原料配比m(CPP)：m(HEMA)：m(St)：m(BPO)=50：0．5：0．6：0．15。     

Poly(3‐chlorothiophene) films prepared by the direct electrochemical oxidation of 3‐chlorothiophene in mixed electrolytes of boron trifluoride diethyl etherate and sulfuric acid

3‐Chlorothiophene (CT) was electrochemically polymerized in mixed electrolytes of a boron trifluoride diethyl etherate solution containing 0–20% (by volume) sulfuric acid. The oxidation potentials of the monomer in these media were measured to be only 1.06–1.31 V (vs Ag/AgCl). These values were much lower than that of CT in acetonitrile and 0.1 mol/L (Bu)₄NBF₄ (1.92 V vs Ag/AgCl). Poly(3‐chlorothiophene) (PCT) films with conductivities of 0.1–2 S cm^?1 were obtained. The structure, morphology, and electrochemical behavior of the PCT films also were investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 502–509, 2003     

Strain-induced crystallization,Part IV: Induction time analysis

The empirical equation, 1/t_i = Ae^Ei/RT, which expresses the exponential dependence of the reciprocal of crystallization induction time, t_i, has been analyzed and shown to be equivalent to the nucleation rate equations derived earlier in Part III (1). Consequently we have used the t_i measurements obtained earlier by Krueger and Yeh to calculate not only the nucleation rate enhancements but also the melting point elevations, the relative crystal thickness changes and molecular coil extension ratios of shear-crystallization polyethylene. It is shown that polyethylene when crystallized between 129 and 131°C at shear rates between 1.56 and 9.70 sec^?1 can have melting point increases of 4.2 to 7.2°C and crystal thickness decreases of 20 to 25 percent, when compared to those crystallized at 130°C in the quiescent state. The predicted “coil” extension in the melt just prior to shear-induced crystallization ranges between 21 and 36 percent. The results of these analyses as well as those on nucleation rates of polyethylene oxide are discussed in detail.     

聚氨酯丙烯酸酯紫外光固化PVC涂料的研制

通过对涂料不同组分的种类及配比进行调节,制备不同配方的PVC清漆。在测试附着力、硬度、耐温、耐水性能的基础上,优化涂料配方,并配制出性能优异的PVC清漆涂料。     

聚乙烯/石墨阻燃复合材料的研究

研究了石墨、可膨胀石墨、膨胀石墨 /聚乙烯复合材料的阻燃性能。结果表明 ,石墨具有一定的阻燃作用 ,可膨胀石墨具有良好的阻燃效果。但可膨胀石墨填充的复合材料力学性能较差     

荧光染料用于涤纶织物染色的荧光性能研究

在实验条件下，染色织物的荧光反射率随荧光染料的浓度增加而增加，超过一定浓度后，有下降趋势；在pH=5左右，荧光反射率最高；荧光增白剂会提高染色织物的荧光反射率，在荧光黄2GFL中，当荧光增白剂的浓度由0.1％增加到5％时，荧光反射率由8．43增加至18．59，而对非荧光染料只有增艳的作用，不产生荧光。荧光染料染色织物的荧光反射率随着加入非荧光染料量的增加而减弱。     

四种杀菌剂对枸杞黑果病的防治效果

枸杞黑果病是枸杞产区的主要病害．发病后造成黑花、黑蕾和黑果，使枸杞产量降低，品质变劣。为探明四种杀菌剂对枸杞黑果病的防治效果及最佳剂量，2003年对下述四种杀菌剂进行了田间药效对比试验，调查防效结果如下：20％三苯基醋酸锡WP450～281g／hm^2(以有效成分计，下同)，20％氟硅唑EC21．08g／hm^21．5％噻霉酮EW16、88～21．08g／hm^2、40％氟硅唑EC450g／hm^2和70％甲基托布津WP787．5g/hm^2对枸杞黑果病防效均在88．25％以上。经LSD检验各处理间防效无显著差异。     

硫醇自组装膜的电化学研究进展

综述了在金电极上硫醇自组装膜的电化学表征方法，性质和应用，介绍了自组装膜上的电子传递机理，并进行了简要的展望。     

发酵工厂中空气净化工艺的合理选择

从节能、降低成本、优化工艺的角度，对无菌空气制备过程中，空气预处理流程的选择、空气净化设备、过滤介质以及设备的遴选进行探讨，以实现工艺和工程设计的优化结合。