Hazelett生产线熔炼工艺探讨

探讨了采用Hazelett生产线,从原料到合格铝液各道工序的操作要求;特别是采用电解铝液,对每道工序操作时间和铝液质量控制提出严格要求。通过实际生产,对现有熔炼炉配置、设备台数、精炼设备配置作了详细阐述,对每道工序要达到的铝液净化参数提出严格要求,经过6次净化提纯,基本满足Hazelett铸机要求,并对熔炼设备配置的不足提出合理化建议。     

Development of mobile miniature natural gas liquefiers

With increasing consumption of natural gas (NG), small NG reservoirs, such as coalbed methane and oil field associated gas, have recently drawn significant attention. Owing to their special characteristics (e.g., scattered distribution and small output), small-scale NG liquefiers are highly required. Similarly, the mixed refrigerant cycle (MRC) is suitable for small-scale liquefaction systems due to its moderate complexity and power consumption. In consideration of the above, this paper reviews the development of mobile miniature NG liquefiers in Technical Institute of Physics and Chemistry (TIPC), China. To effectively liquefy the scattered NG and overcome the drawbacks of existing technologies, three main improvements, i.e., low-pressure MRC process driven by oil-lubricated screw compressor, compact cold box with the new designed heat exchangers, and standardized equipment manufacturing and integrated process technology have been made. The development pattern of “rapid cluster application and flexible liquefaction center” has been eventually proposed. The small-scale NG liquefier developed by TIPC has reached a minimum liquefaction power consumption of about 0.35 kW·h/Nm³. It is suitable to exploit small remote gas reserves which can also be used in boil-off gas reliquefaction and distributed peak-shaving of pipe networks.     

空气预热器实时监控系统堵塞可视化性能研究

针对电站锅炉回转式空气预热器运行时上下表面不可见的问题，本文提出了一种视频监控与故障分析系统，可直接监测转子表面情况。该系统通过视频监控获取图像，结合改进的Retinex算法对其进行处理，实现了以下2个功能:1）能分析积灰程度以判断转子堵塞 情况；2）与温度场融合实时显示转子表面热点分布以预防二次燃烧。该系统已应用于某600 MW机组，实现了在热态环境下对空气预热器转子积灰程度、热点分布、堵塞程度的估算与可视化，大大提高了空气预热器运行的可靠性。     

火电机组负荷分配中多源不确定性因素影响分析

不确定性因素存在于火电机组负荷分配中，影响机组负荷分配、节能环保目标。本文综合考虑负荷预测不确定性、机组煤耗率不确定性与其CO2排放系数不确定性，分别构建火电机组一次能源消耗成本与CO2排放量最小目标下的火电机组负荷优化分配模型；以此为基础，引入析因分析方差分解方法，量化多源不确定性因素单独与交互作用下对节能、环保目标的影响程度。结果表明:负荷预测不确定性对火电机组节能、环保目标影响最为显著，相对影响程度分别为51.13%、62.70%；机组煤耗特性及其CO2排放系数影响次之，相对影响程度分别为47.58%、34.95%。此研究结果对不确定性条件下电力系统负荷分配具有借鉴价值。     

Corrosion resistance of Al–Cr-slag containing chromium–corundum refractories to slags with different basicity

Al–Cr slag is the solid waste generated by the smelting of Cr metal. It presents a range of environmental hazards. This study addressed the corrosion resistance of Al–Cr slag containing chromium–corundum refractories to slags with different basicity. Herein, we provide suggestions for the use of Cr–corundum of different basicity in kilns. Al–Cr slag, brown fused Al₂O₃, and chrome green were used as the raw materials, with pure calcium aluminate cement being used as a binder. The brick samples, prepared using different blends of chrome green and corundum, were fired at 1600?°C, and subsequently subjected to a slag corrosion test. After corrosion by slag of different basicity, the phase composition and microstructure of the sample were analyzed by X-ray diffraction, energy dispersive spectrometer and scanning electron microscopy. There were two major findings. First, Cr–corundum brick made from Al–Cr slag has a better slag corrosion resistance than that made from Cr₂O₃ and brown fused Al₂O₃. Second, Cr–corundum brick made from Al–Cr slag has superior corrosion resistance to slag with a CaO:SiO₂ ratio of 2:1.     

基于振动实测的非均质地层钻头失效分析与对策

四川盆地作为国内页岩气开发的重点区域,通过近几年的不断攻关和实践,机械钻速得到了提高,但由于受地层复杂、可钻性差、非均质性强等地质因素的影响,导致井下钻柱系统不良振动剧烈,容易出现钻头损坏严重、钻速较低等问题,严重影响了钻井时效。为了解决上述难题,以该盆地涪陵工区上二叠统龙潭组—中二叠统茅口组为例,采用井下振动高频测量工具的实测手段,测量了钻头—钻柱系统的动态振动加速度参数,结合地层的岩性和矿物组分分析,研究钻头失效原因与对策,并开展了现场试验。研究结果表明:①在非均质地层中钻进的钻头—钻柱系统产生了大于40 m/s~2的高幅值瞬时冲击振动,高幅值的瞬时冲击是导致钻头先期失效的主要原因;②提出了抑制高幅值的瞬时冲击振动采用"减振+增压"工具组合和避免井下工具共振的钻井参数;③采用钻井新参数的试验井比邻井的高幅值瞬时振动降低了17%,单只钻头进尺增加24%,钻头工作环境得到了较大的改善,钻头使用数量减少。结论认为,该研究成果能够有效地改善钻头—钻柱系统的振动状态,有利于达成延长钻头使用寿命的目标。     

水文序列相依变异识别的RIC定阶准则——以自回归模型为例

水文过程相依性是水文变异的主要表现形式之一,应用自回归模型对其进行拟合时合理确定模型阶数是一个难点问题。本文在分析AIC和BIC准则的基础上,提出了一种以原序列与其相依成分的相关系数作为拟合度指标,同时借用信息熵形式的函数式,作为模型不确定性度量指标的自回归模型定阶准则(简称RIC准则)。以AR(1)、AR(2)、AR(3)和AR(4)模型为例进行统计试验,将不同序列长度下该准则的定阶准确率与其他定阶准则进行比较,试验结果表明,RIC准则对于上述模型均具有较好的适应性,且定阶准确率远高于AIC准则,其中对于前三阶模型RIC准则优于BIC准则,但四阶模型略低于BIC准则。RIC准则的优势是可以同时满足模型定阶、相依程度分级与模型检验的需求,将其应用于实测水文序列分析,结果显示,该准则能较准确地识别自回归模型的阶数,且符合提出的"相依有变异而残差无变异的最小阶数"的检验标准。     

马钢张庄矿高压辊磨机装配工艺研究

针对马钢张庄矿高压辊磨机辊套疲劳断裂严重、对辊精度不能满足生产要求等问题，马钢重机公司根据张庄矿实际生产要求对对辊进行国产化，国产化内容包括辊轴、辊套等零部件的新制以及装配工艺攻关，通过技术研发同时结合实际生产经验，成功对高压辊磨机辊套与辊轴以及辊轴与轴承进行装配，完成了张庄矿高压辊磨机整对对辊的国产化，为该型设备后续生产及优化提供了理论和实践参考依据。