Time-dependent deformation in an enhanced SiC/SiC composite

Time-dependent deformation in an enhanced SiC/SiC composite has been studied under constant load at high temperatures of 1200 °C, 1300 °C, and 1400 °C. Creep damage evolution was evaluated by a Young’s-modulus change of partial unloading and microscopic observation. The addition of the glassy phase in the matrix is very effective for protecting the composite from oxidation. The transient creep is dominant in creep life at all the temperatures. An empirical equation is proposed to describe creep behavior of the composite. It is found that creep activation energy increases with creep time at stresses lower than matrix cracking stress, but the activation energy remains constant at stresses higher than the matrix cracking stress. The creep strain rate of the composite is considered to be controlled by creep of fibers based on examining the time, strain, stress, and temperature dependencies of creep strain rates.     

A demonstrative study for the wind and solar hybrid power system

In March 1995, a small scale wind and solar hybrid power system was installed at Ashikaga Institute of Technology. Until now, the authors have acquired the data of the output of the hybrid power plant along with wind speed, wind direction, and the solar radiation, in order to demonstrate a complementary relationship between solar energy and wind energy.After nine months operation of the system, the authors confirmed that there exists a complementary relationship between solar energy and wind energy. We also found, however, that the power output by wind does not have much prospect compared to that by solar cell especially in summer season in Ashikaga area.     

Radiation tolerance for the SMASH-series front-end chips for a silicon micro-strip detector

The radiation tolerance for prototype front-end chips designed for a silicon micro-strip detector was examined with a ⁶⁰Co irradiation source to establish an allowable range of the radiation dose. The irradiated front-end chips were SMA²SH-64A, a 64-channel preamplifier array; SMA²SH-1, a single-channel preamplifier circuit with a comparator; and Control-C, a digital-control chip for the preamplifiers.     

Effective thermal conductivity of compressed woods

Compression is one solution to improve the strength of softwoods. The effective thermal conductivities of compressed Japanese cedars (cryptomeria japonica), which were compressed in the radial direction of the wood, were measured. Both the effective thermal conductivities in the tangential and fiber directions increase proportionally to the density increment due to the compression. However, the thermal conductivity in the radial direction (compression direction) increases slightly with the density increment. Numerical computations were conducted to explain the characteristics of thermal conductivity in the radial direction by using a microscopic heat conduction model for the compressed wood. The numerical results were compared with the measured values. And the physical mechanism of the heat conduction in the compressed woods is discussed.     

Development of a single loop EPR test method and its relation to grain boundary microchemistry for alloy 600

A single loop electrochemical potentiokinetic reactivation test method has been developed for alloy 600 that produces good passivation on all the surfaces, good etching during the reactivation scan and no appreciable pitting. It is able to quantify and discriminate between samples with a wide range of degree of sensitization. The Pa value correlates well with the minimum level of chromium in the depletion regions at the grain boundaries. It has been shown that the width of the attacked regions is much larger than the width of chromium depletion regions and it does not show any direct correlation with either depth or width or with a volume parameter of chromium depletion regions. It has been shown that the chromium carbides are not attacked during the test and that the intragranular regions attacked during the test are the sites of chromium carbides in the grain matrix. A modified Pa parameter is shown to be sensitive down to 7.5 wt% chromium in the depletion regions and indicates that the intragranular carbides have shallower depletion profiles than those at grain boundaries. Comparison of the results of the single loop and the double loop tests showed a good correlation.     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

Formation of low-resistivity poly-Si and SiNx films by Cat-CVD for ULSI application

In this paper, bulk-Si metal–oxide–semiconductor field effect transistors (MOSFETs) are fabricated using the catalytic chemical vapor deposition (Cat-CVD) method as an alternative technology to the conventional high-temperature thermal chemical vapor deposition. Particularly, formation of low-resistivity phosphorus (P)-doped poly-Si films is attempted by using Cat-CVD-deposited amorphous silicon (a-Si) films and successive rapid thermal annealing (RTA) of them. Even after RTA processes, neither peeling nor bubbling are observed, since hydrogen contents in Cat-CVD a-Si films can be as low as 1.1%. Both the crystallization and low resistivity of 0.004 Ω·cm are realized by RTA at 1000 °C for only 5 s. It is also revealed that Cat-CVD SiN_x films prepared at 250 °C show excellent oxidation resistance, when the thickness of films is larger than approximately 10 nm for wet O₂ oxidation at 1100 °C. It is found that the thickness required to stop oxygen penetration is equivalent to that for thermal CVD SiN_x prepared at 750 °C. Finally, complementary MOSFETs (CMOSs) of single-crystalline Si were fabricated by using Cat-CVD poly-Si for gate electrodes and SiN_x films for masks of local oxidation of silicon (LOCOS). At 3.3 V operation, less than 1.0 pA μm⁻¹ of OFF leakage current and ON/OFF ratio of 10⁷–10⁸ are realized, i.e. the devices can operate similarly to conventional thermal CVD process.     

The heat transfer and pressure drop characteristics of finned tube banks in forced convection (effects of fin height on pressure drop characteristics)

In recent years the requirement for the reduction of energy consumption has been increasing to solve the problems of global warming and the shortage of petroleum resources. For example, in the power generation field, as thermal power generation occupied 60% of the power generation demand, considerable improvement of the thermal efficiency is required. This paper describes the pressure drop characteristics of finned tube banks used for heat exchangers in thermal power generation that were clarified by testing serrated finned tube banks with different fin heights for improved heat transfer and conventional spiral finned tube banks with different fin heights, and an equation to predict pressure drop which is necessary for the heat exchanger design is proposed. © 2006 Wiley Periodicals, Inc. Heat Trans Asian Res, 35(3): 179–193, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20112     

Neurotoxic effects of sodium nitroprusside in rat hippocampal slices

The effect of a permanent transection on myelin gene expression in a regenerating sciatic nerve and in an adult sciatic nerve was compared to establish the degree of axonal control exerted upon Schwann cells in each population. First, the adult sciatic nerve was crushed, and the distal segment allowed to regenerate. At 12 days post-crush, the sciatic nerve was transected distal to the site of crush to disrupt the Schwann cell-axonal contacts that had reformed. Messenger RNA (mRNA) levels coding for five myelin proteins were assayed in the distal segment of the crush-transected nerve after 9 days and were compared to corresponding levels in the distal segments of sciatic nerves at 21 days post-crush and 21 days post-transection using Northern blot and slot-blot analysis. Levels of mRNAs found in the distal segment of the transected and crush-transected nerve suggested that Schwann cells in the regenerating nerve and in the mature adult nerve are equally responsive to axonal influences. The crush-transected model allowed the genes that were studied to be classified according to their response to Schwann cell-axonal contact. The levels of mRNAs were 1) down-regulated to basal levels (P0 and MBP mRNAs), 2) down-regulated to undetectable levels (myelin-associated glycoprotein mRNAs), 3) upregulated (mRNAs encoding 2'3'-cyclic nucleotide phosphodiesterase and beta-actin), or 4) not stringently controlled by the removal of Schwann cell-axonal contact (proteolipid protein mRNAs). This novel experimental model has thus provided evidence that the expression of some of the important myelin genes during peripheral nerve regeneration is dependent on continuous signals from the ingrowing axons.     

Lichen sclerosus et atrophicus in a band-like arrangement

We report a case of lichen sclerosus et atrophicus (LSA) in a band-like arrangement. The patient had a white atrophic plaque on the left breast which showed the typical histological features of LSA. One month later, the patient had developed multiple, brown-colored plaques from the right breast to the right upper arm following the distribution of the peripheral nerve. These plaques showed the mild histological changes indicative of LSA. This band-like arrangement of LSA appears to be unique.