Lateral habits ofn-alkane single crystals

The lateral crystal habits ofn-alkanes (n-C _n H_2n+2) have been observed just below the melting points by optical microscopy forn=18, 19, 20, 22, 24, 34, 44, 50 and 65. The shape of the crystals depends on the crystal phase: circular in the rotator phase, lenticular in phase C, and diamond in the low-temperature phase. The rounding of the lateral shape can be explained in terms of thermal roughening of the lateral faces in the disordered phases at high temperature.     

Elastic effects in the flow of polymer solutions in channels of variable cross section and a porous medium

The manifestation of elastic effects during the filtration of polymer solutions is analyzed theoretically.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 49, No. 3, pp. 390–397, September, 1985.     

Comparison of nutrient cycling in a surface-flow constructed wetland and in a facultative pond treating secondary effluent.

There is a growing interest in the possibilities offered by combinations of waste stabilisation ponds (WSP) and constructed wetlands (CW). The purpose of our study was to compare treatment performances and nutrient cycling in a surface-flow wetland (SFW) and in a WSP treating secondary effluent. In the period between 2000 and 2003, a pilot SFW and a pilot WSP were constructed at the outlet of the wastewater treatment plant and their performance monitored while both were active under the same conditions. The SFW was planted with Phragmites australis and Eichhornia crassipes, while in the WSP development of algae was spontaneous. Performance efficiency was monitored by means of evaluation of physical and chemical parameters in water, by measurement of plant productivity and by analysis of N and P contents in biomass. The SFW with macrophytes proved more efficient in decreasing the suspended solids (64.6%), settleable solids (91.8%), organic N (59.3%), total N (38%), COD (67.2%) and BOD5 (72.1%) than the WSP. The WSP with algae was more efficient in treatment of ammonia nitrogen (48.9%) and ortho-phosphate (43.9%). The results of this study provide data that are of help in optimising combinations of SFW and WSP.     

Compact implementation of high-performance CMOS current mirror

A high-performance compact current mirror implementation with very low input resistance, very high output resistance, high copying accuracy, low input and output voltage supply requirements and high bandwidth is proposed. The circuit characteristics are validated with simulations in 0.5 /spl mu/m CMOS technology and with experimental results.     

一方水土养一方人

我国幅员辽阔，产物众多，各地的饮食习惯也不同。非常有趣的是，特别的饮食习惯不仅影响了各地人的生活，甚至还塑造了他们的性格。正所谓“一方水土养一方人”。     

Low Electrical Percolation Threshold of Silver and Copper Nanowires in Polystyrene Composites

Silver and copper nanowires have been synthesized using a scalable method of AC electrodeposition into porous aluminum oxide templates, which produces gram quantities of metal nanowires ca. 25 nm in diameter and up to 5 and 10 μm in length for Ag and Cu, respectively. The nanowires have been used to prepare polystyrene nanocomposites by solution processing. Electrical resistivity measurements performed on polymer nanocomposites containing different volume fractions of metal indicate that low percolation thresholds of nanowires are attained between compositions of 0.25 and 0.75 vol %.     

Effect of starting particle size on hot-pressing of magnesium oxide powder prepared by vapour-phase oxidation process

Effect of starting particle size on hot-pressing of magnesium oxide (MgO) powder was examined using seven kinds of MgO powders prepared by a vapour-phase oxidation process; the average primary particle sizes were 11, 25, 32, 44, 57, 107 and 261 nm. These compressed powders (compacts) were hot-pressed at a temperature between 900 and 1300°C. The densifications of these compacts during the hot-pressing proceeded via (i) the sintering of primary particles within secondary particles and the rearrangement of secondary particles/grains (900°C), (ii) the gradual grain growth controlled by the pore migration (900∼1100°C) and (iii) the rapid grain growth due to the active mass transfer (1300°C); the grain sizes of MgO compacts hot-pressed at and below 1100°C were <1 μm, while those at 1300°C attained 20∼30 μm. The transluscent compact with the relative density of 99.7% could be obtained when the compressed powder with the average primary particle size of 44 nm was hot-pressed at a temperature as low as 1100°C for 1 h. This revised version was published online in November 2006 with corrections to the Cover Date.     

Unfavorable mechanical effects of heat and moisture exchangers in ventilated patients

OBJECTIVE: To investigate the mechanical effects of artificial noses. SETTING: A general intensive care unit of a university hospital. PATIENTS: 10 patients in pressure support ventilation for acute respiratory failure. INTERVENTIONS: The following three conditions were randomly tested on each patient: the use of a heated humidifier (control condition), the use of a heat and moisture exchanger without filtering function (HME), and the use of a combined heat and moisture exchanger and mechanical filter (HMEF). The pressure support level was automatically adapted by means of a closed-loop control in order to obtain constancy, throughout the study, of patient inspiratory effort as evaluated from airway occlusion pressure at 0.1 s (P0.1). Patient's ventilatory pattern, P0.1, work of breathing, and blood gases were recorded. MEASUREMENTS AND MAIN RESULTS: The artificial noses increased different components of the inspiratory load: inspiratory resistance, ventilation requirements (due to increased dead space ventilation), and dynamic intrinsic positive end-expiratory pressure (PEEP). The additional load imposed by the artificial noses was entirely undertaken by the ventilator, being the closed-loop control of P0.1 effective to maintain constancy of patient inspiratory work by means of adequate increases in pressure support level. CONCLUSIONS: The artificial noses cause unfavorable mechanical effects by increasing inspiratory resistance, ventilation requirements, and dynamic intrinsic PEEP. Clinicians should consider these effects when setting mechanical ventilation and when assessing patients' ability to breathe spontaneously.