Standby power system VRLA battery reserve life estimation scheme

This paper presents a valve-regulated lead acid (VRLA) battery reserve life estimation scheme. The scheme is adaptive in both type and frequency of involvement. The scheme is based on capacity trending with the support of a number of state-of-health (SOH) indicators. These SOH indicators include accumulated thermal stress, float voltage, and indicators acquired from the start-of-discharge (coup de fouet) region. An implementation test case is given, indicating that the scheme is capable of providing an accurate estimation of reserve life long before the end of life. Furthermore, the estimation accuracy improves as the end of battery life approaches.     

Effect of Thin Film Thicknesses and Materials on the Response of RTDs and Microthermocouples

Fabrication and thermal characterization of a resistance temperature detector (RTD) heater and microthermocouples (MTs) on silicon substrates have been reported in this paper. The influence of film thickness and nickel-gold (Au) electroplating on RTD on its steady-state temperature with respect to its steady-state electrical power input and resistance is studied. Further, the thermal effects of multiple thermocouples in a thermopile as well as the effects of Au layers in the contact pads of the thermopiles on their open-circuit Seebeck voltage are studied. Therein lies the novelty of this paper. The in situ operating relationships for the RTD heater and the MT are provided     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

The radiative recombination coefficient and the internal quantum yield of electroluminescence in silicon

The results of the analysis of variations in the radiative recombination coefficient with varying doping level and concentration of excess electron-hole pairs are reported. It is shown that, along with the effect of narrowing of the band gap calculated in the many-electron approximation, the effect of screening of the Coulomb interaction responsible for the decrease in the excition binding energy should be taken into account. Both effects produce similar trends and decrease the radiative recombination coefficient with increasing levels of doping or injection. The contributions of excitonic radiative recombination and band-to-band radiative recombination to the total radiative recombination coefficient are separated from each other. It is shown that, in the region of room temperature, both contributions are comparable, while at liquid-nitrogen temperature, the excitonic component dominates over the band-to-band component. The results obtained by refined calculations of the limiting value of the internal quantum yield of electroluminescence for the silicon diodes and p-i-n structures are presented. It is shown that the internal quantum yield of electroluminescence can be as high as 14%. However, this values sharply decreases with increasing surface recombination rate and decreasing lifetime of excess charge carriers in the bulk.     

A Low-Power CMOS Linear-in-Decibel Variable Gain Amplifier With Programmable Bandwidth and Stable Group Delay

This brief presents a new circuit architecture for linear-in-decibel, constant-bandwidth variable gain amplifier (VGA). To obtain high linearity under low-voltage operation, this VGA is a closed-loop structure. In loop amplifier design, two techniques are applied: first, the loop amplifier is given finite input impedance. This arrangement keeps the VGA bandwidth constant under different gain setting. Second, a current-buffered compensation is applied for loop stability. Compared to the Miller compensation, this method achieves wider bandwidth. The prototype chip using 0.18-mum CMOS technology demonstrates that -10- to 20-dB gain and 0.5- to 30-MHz bandwidth can be programmed independently. The group delay difference within 30-dB gain control range is smaller than 1%. The total circuit dissipates 1.35 mA from a 1.8-V supply     

Organic matter release in low temperature thermal treatment of biological sludge for reduction of excess sludge production.

Thermal treatment applied in association with a biological system allows for a significant reduction in excess sludge production (approximately 50%). In general, heat treatment is described as a sludge disintegration technique. This paper offers a thorough study on the impact of heat treatment, at temperatures below 100 degrees C, on the solubilisation of the sludge COD and its biodegradability. Discontinuous heating experiments were performed on activated and digested sludge. At all temperatures tested the released COD for digested sludge was systematically higher than that for activated sludge (15 and 40%, respectively, at 95 degrees C for 40 min of contact time). For the first 30 min, a 1st order kinetic, with respect to the residual COD, was systematically found. In the range of 40-95 degrees C, digested sludge had a lower activation energy than activated sludge (26 kcal/mol compared to 70-160 kcal/mol). COD solubilisation is thus more positively influenced by temperature in the case of activated sludge. This may be due to the significant difference in the ratio of protein/carbohydrate in digested and activated sludge (1-5 and 0.2-0.7, respectively). The increase in the COD/TKN ratio in the solubilised fraction after thermal treatment of activated sludge suggests a preferential solubilisation of proteins over carbohydrates. Respirometric tests performed on the solubilised COD showed that whatever the sludge origin, only 40-50% of released COD is biodegradable at a conventional hydraulic retention time (i.e., 24 h). Hence, heat treatment would act more through organic matter solubilisation rather than by a biodegradability increase.     

Radioecological state of the territory and water area in Guba Andreev

The radioecological conditions which developed on the territory over the long operating time of the object of the naval fleet in Guba Andreev are described. The results of an analysis of the sources of the real and potential danger and measures to prevent dangerous effects for the environment and the workers at the time remediation work is performed are discussed. __________ Translated from Atomnaya énergiya, Vol. 101, No. 1, pp. 49–55, July, 2006.     

Results of a User Study on 2D Hurricane Visualization

We present the results from a user study looking at the ability of observers to mentally integrate wind direction and magnitude over a vector field. The data set chosen for the study is an MM5 (PSU/NCAR Mesoscale Model) simulation of Hurricane Lili over the Gulf of Mexico as it approaches the southeastern United States. Nine observers participated in the study. This study investigates the effect of layering on the observer's ability to determine the magnitude and direction of a vector field. We found a tendency for observers to underestimate the magnitude of the vectors and a counter‐clockwise bias when determining the average direction of a vector field. We completed an additional study with two observers to try to uncover the source of the counter‐clockwise bias. These results have direct implications to atmospheric scientists, but may also be able to be applied to other fields that use 2D vector fields.     

A prototype of a superconducting magnet for a 170-GHz gyrotron

Within the framework of the “International Thermonuclear Experimental Reactor” (ITER) program, a prototype of a superconducting magnet for a 170-GHz gyrotron has been developed, manufactured, and tested. The operating induction value (7.1 T at the center of a 219-mm-diameter cold hole and 8.1 T on the winding) is reached at a current of 185.2 A. In the final version of the magnet, the required induction value was reached without aging. Special requirements are imposed on the distribution of the magnetic field along the axis, including an abrupt field decrease on both sides of the magnet. Axial forces are additionally taken by a special device. The magnet’s sections are wound with multifiber conductors based on niobium-tin and niobium-titanium alloys. Seventeen resistive shunts are provided for protecting sections during their transition to the normal state. The magnet is equipped with a device for removing a part of energy from the sections. Mechanical stresses in the magnet’s sections and the structure’s power elements have been measured during tests.