Routing Correlated Data with Fusion Cost in Wireless Sensor Networks

In this paper, we propose a routing algorithm called minimum fusion Steiner tree (MFST) for energy efficient data gathering with aggregation (fusion) in wireless sensor networks. Different from existing schemes, MFST not only optimizes over the data transmission cost, but also incorporates the cost for data fusion, which can be significant for emerging sensor networks with vectorial data and/or security requirements. By employing a randomized algorithm that allows fusion points to be chosen according to the nodes' data amounts, MFST achieves an approximation ratio of 5/4log(k + 1), where k denotes the number of source nodes, to the optimal solution for extremely general system setups, provided that fusion cost and data aggregation are nondecreasing against the total input data. Consequently, in contrast to algorithms that only excel in full or nonaggregation scenarios without considering fusion cost, MFST can thrive in a wide range of applications     

Parametric effects on the transient Voltage performance of a DC superconducting cable

The objective of this work was to determine the significant parameters of a 3-GW 200-kV dc superconducting cable system which influence the transient voltage distribution in the various parts of the cable. The cable system consists of four coaxial metallic cylinders. It was found that the dielectric constant and the electrical resistivity of the soil significantly affect the severity of the transient voltages; lower dielectric constant and higher resistivity of the soil will increase the magnitudes of the transient voltages by increasing the earth-return impedance. It was also found that the effect of the conductor internal impedances of the cable is insignificant. Shorting the coaxial cylinders of the cryogen flow and the cryostat will lessen the severity of the transient voltages. Grounding the second, third, and fourth cylinders at regular intervals with low-impedance grounding impedance will also improve the transient performance of the cable. More research is needed to evaluate these procedures.     

Sigma-delta modulators operating at a limit cycle

A new type of sigma-delta modulator that operates in a special mode named limit-cycle mode (LCM) is proposed. In this mode, most of the SDM building blocks operate at a frequency that is an integer fraction of the applied sampling frequency. That brings several very attractive advantages: a reduction of the required power consumption per converted bandwidth, an immunity to excessive loop delays and to digital-analog converter waveform asymmetry and a higher tolerance to clock imperfections. The LCMs are studied via a graphical application of the describing function theory. A second-order continuous time SDM with 5 MHz conversion bandwidth, 1 GHz sampling frequency and 125 MHz limit-cycle frequency is used as a test case for the evaluation of the performance of the proposed type of modulators. High level and transistor simulations are presented and compared with the traditional SDM designs.     

Nonlinear crack dynamics and scaling aspects of fracture (experimental and theoretical study)

Nonlinear dynamics of crack propagation are investigated experimentally and theoretically with the goal of clarifying the nature of limiting crack velocity, the transition from steady state to branching regimes of crack dynamics, and the dynamics of crack arrest. The theoretical explanation of limiting steady-state crack velocity and the transition to a branching regime was proposed due to the study of collective behavior of a microcrack ensemble at the crack tip area. The experimental study of crack dynamics was carried out in a preloaded plate PMMA specimen using the high-speed camera coupled with the photo-elasticity method, the point stress recording with a laser system, and the failure surface roughness measurement.     

EBSP study of the annealing behavior of aluminum deformed by equal channel angular processing

Commercial purity aluminum (99.5%) was fabricated by equal channel angular pressing (ECAP) up to total accumulated strains of approx. 10. The annealing behavior of material deformed to total strains of approx. 1 and 10 was investigated, using heat treatments of 2 h at various temperatures from 100 to 500 °C. The microstructure of the annealed materials was characterized using the electron back-scatter pattern technique. A number of parameters were determined including the distribution and average values of both the boundary spacings and misorientations. For samples deformed to a total strain of 1, annealing resulted in discontinuous recrystallization. For samples deformed to a total strain of 10, annealing resulted in microstructures exhibiting characteristics of both uniform coarsening and, in a number of places, of discontinuous recrystallization. An attempt was made, based on the boundary spacing distributions, to separate these two components. The grain size after annealing was still however small, being just 6.4 μm after 2 h at 300 °C.     

Nanoscale Crystallization in Amorphous Fe–P–Mn Alloys

Mössbauer effect measurements and physicochemical analysis demonstrate that annealing of amorphous Fe–P–Mn alloys leads to the formation of a nanocrystalline structure.     

Fabrication, assembly, and characterization of molecular electronic components

One of the ultimate miniaturizations in nanotechnology is molecular electronics, where devices will consist of individual molecules. There are many complications associated with the use of molecules in electronic devices, such as the electronic perturbations in the molecule associated with being bonded to an electrode, how electrons traverse the metal-molecule junction, and the difficulty of macroscopically addressing single to very few molecules. Whether fabricating a test structure or a usable device, the use of self-assembly is fundamental to the fabrication of molecular electronic devices. We will discuss how to fabricate self-assembled monolayers into test assemblies and how to use intermolecular interactions to direct molecules into desired positions to create nanostructures and to connect functional molecules to the outside world. These assemblies serve as test structures for measurements on single or bundled molecules. The development of several experimental techniques, including various scanning probes, mercury drop junctions, break junctions, nanopores, crossed wires, and other techniques using nanoparticles have enabled the ability to test these structures and make reproducible measurements on single molecules. Many of these methods have been developed to test molecules with potential for integration into devices such as oligo (phenylene-ethynylene) molecules and other /spl pi/-conjugated molecules, in ensemble or single-molecule measurements.     

TEM Studies of High Temperature Corrosion Behaviour of TiAl Intermetallics with Surface Modifications

The oxidation/sulphidation behaviour of a Ti‐46.7Al‐1.9W‐0.5Si alloy with a TiAl₃ diffusion coating was studied in an environment of H₂/H₂S/H₂O at 850^oC. The kinetic results demonstrate that the TiAl₃ coating significantly increased the high temperature corrosion resistance of Ti‐46.7Al‐1.9W‐0.5Si. The SEM, EDX, XRD and TEM analysis reveals that the formation of an Al₂O₃ scale on the surface of the TiAl₃‐coated sample was responsible for the enhancement of the corroison resistance. The Ti‐46.7Al‐1.9W‐0.5Si alloy was also modified by Nb ion implantation. The Nb ion implanted and as received sampels were subjected to cyclic oxidation in an open air at 800^oC. The Nb ion implantation not only increased the oxidation resistance but also substantially improved the adhesion of scale to the substrate.     

On optimal sequential prediction for general processes

This paper considers several aspects of the sequential prediction problem for unbounded, nonstationary processes under pth power loss /spl lscr//sub p/(u,v)=|u-v|/sup p/, 1相似文献   

Self-organized public-key management for mobile ad hoc networks

In contrast with conventional networks, mobile ad hoc networks usually do not provide online access to trusted authorities or to centralized servers, and they exhibit frequent partitioning due to link and node failures and to node mobility. For these reasons, traditional security solutions that require online trusted authorities or certificate repositories are not well-suited for securing ad hoc networks. We propose a fully self-organized public-key management system that allows users to generate their public-private key pairs, to issue certificates, and to perform authentication regardless of the network partitions and without any centralized services. Furthermore, our approach does not require any trusted authority, not even in the system initialization phase.