The effect of heat treatments on the properties of Ti/Pt heating elements for gas sensor applications

Ti/Pt as heating element for gas sensor applications was fabricated on silicon (Si) wafer substrate. The fabricated device was subjected to heat treatment at different prescribed time periods for thermal stability. The energy dispersion spectroscopy (EDS) results of the device indicated that there were no Ti traces on the Pt surface after heat treatment at 450 °C for 3 and 4 h in an argon (Ar) atmosphere. A maximum temperature coefficient of resistance (TCR) with a value of 2.88×10^?3 K^?1 was obtained for the device with 3 h heat treatment.     

Preparation, Characterization, and Microwave Dielectric Properties of Sr2La3Nb1−x Ta x Ti4O17 (0 ≤ x ≤ 1) Ceramics

Sr₂La₃Nb_1?x Ta _x Ti₄O₁₇ (0 ≤ x ≤ 1) ceramics were processed via a solid-state mixed oxide route. Sr₂La₃Nb_1?x Ta _x Ti₄O₁₇ (0 ≤ x ≤ 1) solid solutions were single phase in the whole range of x values within the x-ray diffraction (XRD) detection limit. The microstructure comprised elongated and needle-shaped grains. The ceramics exhibit relative permittivity (ε _r) of 73 to 68.6, product of unloaded quality factor and resonant frequency (Q _u f ₀) of 7100 GHz to 9500 GHz, and temperature coefficient of resonant frequency (τ _f) of 78.6 ppm/°C to 56.6 ppm/°C.     

An Enhanced A-MSDU Frame Aggregation Scheme for 802.11n Wireless Networks

The main goal of the IEEE 802.11n standard is to achieve a minimum throughput of 100 Mbps at the MAC service access point. This high throughput has been achieved via many enhancements in both the physical and MAC layers. A key enhancement at the MAC layer is frame aggregation in which the timing and headers overheads of the legacy MAC are reduced by aggregating multiple frames into a single large frame before being transmitted. Two aggregation schemes have been defined by the 802.11n standard, aggregate MAC service data unit (A-MSDU) and aggregate MAC protocol data unit (A-MPDU). As a consequence of the aggregation, new aggregation headers are introduced and become parts of the transmitted frame. Even though these headers are small compared to the legacy headers they still have a negative impact on the network performance, especially when aggregating frames of small payload. Moreover, the A-MSDU is highly influenced by the channel condition due mainly to lack of subframes sequence control and retransmission. In this paper, we have proposed an aggregation scheme (mA-MSDU) that reduces the aggregation headers and implements a retransmission control over the individual subframes at the MSDU level. The analysis and simulations results show the significance of the proposed scheme, specifically for applications that have a small frame size such as VoIP.     

Determination of residual organic matter in extracted oil sands using a low temperature ashing method

The application of a low temperature ashing method for estimating total residual organic matter (toluene insolubles) in oil sands is described. A linear correlation exists between organic carbon content and loss on ignition at 400 ± 10 °C of solvent extracted oil sands. The ratio between total organic carbon and the weight loss on ignition (CT/LOl) owing to the removal of residual organic matter is much lower than that obtained for toluene soluble bitumen fractions, indicating very different chemical composition for the residual organic matter. The measured carbon content of the residual organic matter in oil sands suggests that this material could be a mixture of various fractions contained in resins, asphaltenes, asphaltic acids and humic acids.     

Review on zirconate-cerate-based electrolytes for proton-conducting solid oxide fuel cell

The performance of low-to-intermediate temperature (400–800?°C) solid oxide fuel cells (SOFCs) depends on the properties of electrolyte used. SOFC performance can be enhanced by replacing electrolyte materials from conventional oxide ion (O^2-) conductors with proton (H⁺) conductors because H⁺ conductors have higher ionic conductivity and theoretical electrical efficiency than O^2- conductors within the target temperature range. Electrolytes based on cerate and/or zirconate have been proposed as potential H⁺ conductors. Cerate-based electrolytes have the highest H⁺ conductivity, but they are chemically and thermally unstable during redox cycles, whereas zirconate-based electrolytes exhibit the opposite properties. Thus, tailoring the properties of cerate and/or zirconate electrolytes by doping with rare-earth metals has become a main concern for many researchers to further improve the ionic conductivity and stability of electrolytes. This article provides an overview on the properties of four types of cerate and/or zirconate electrolytes including cerate-based, zirconate-based, single-doped cerate–zirconate and hybrid-doped cerate–zirconate. The properties of the proton electrolytes such as ionic conductivity, chemical stability and sinterability are also systematically discussed. This review further provides a summary of the performance of SOFCs operated with cerate and/or zirconate proton conductors and the actual potential of these materials as alternative electrolytes for proton-conducting SOFC application.     

Recent Developments and Applications of Ionic Liquids in Gas Separation Membranes

Flue gas emissions and the harmful effects of these gases urge to separate and capture these unwanted gases. Ionic liquids due to negligible vapor pressure, thermal stability, and wide electrochemical stability have expanded its application in gas separations. A comprehensive overview of the recent developments and applications of ionic liquid membranes (ILMs) for gas separation is given. The three general classifications of ILMs, such as supported ionic liquid membranes (SILMs), ionic liquid polymeric membranes (ILPMs), and ionic liquid mixed‐matrix membranes (ILMMMs) along with their applications, for the separation of various mixed gases systems is discussed in detail. Furthermore, issues, challenges, computational study, and future perspectives for ILMs are also considered.