Formation and retention of local melted films in AZ91 friction stir spot welds

The formation of local melted films during friction stir spot welding of as-cast AZ91D and thixomolded AZ91 material is investigated. The average temperatures close to the tip of the rotating pin vary from 438 to 454 °C during the dwell period in friction stir spot welding. These measured temperature values are higher than the melting temperature of α-Mg + Mg₁₇Al₁₂ eutectic (437 °C). It is suggested that the temperature in the stir zone during the dwell period is determined by the relative proportions of α-Mg and (α-Mg + Mg₁₇Al₁₂) eutectic material, which are incorporated during friction stir spot welding. Based on the stir zone temperature measurements and a detailed examination of material located at the root of the pin thread it is suggested that material is moved downwards via the pin thread and into the stir zone during the dwell period in friction stir spot welding. Evidence of local melted film formation is observed in the stir zone of AZ91 spot welds. It is suggested that melted films are retained since their dissolution rate is much slower in the high temperature stir zone than it is when melted films is formed in the stir zone during Al 7075-T6 friction stir spot welding. The spontaneous melting temperature, solute diffusion rate and the thermodynamic driving force for droplet dissolution are much higher during Al 7075-T6 friction stir spot welding.     

杭-宁输气管道工程定向钻穿越设计浅析

杭州-宁波天然气输气管道工程（简称杭-宁输气管道工程）是浙江省天然气长输管网主干线之一，根据工程河流穿越众多、渠塘穿越频繁的特点，对杭-宁输气管道工程水域穿越的特点和穿越方式作了总结；重点分析了水域定向钻穿越设计及需要注意的问题，为今后浙江省天然气管网建设的水域穿越设计作了探讨。     

Photoreactivation of Escherichia coli following medium-pressure ultraviolet disinfection and its control using chloramination.

Ultraviolet (UV) disinfection is becoming increasingly popular as an alternative disinfection technology to chlorination in recent years. In this study, we investigated the photoreactivation of Escherichia coli following medium-pressure (MP) UV disinfection of synthetic water by a bench-scale collimated beam apparatus. The UV doses ranged from 1.6 -19.7 mWs/cm2 and photoreactivation was investigated for 6 hours under fluorescent light. In addition, chloramination was applied after UV disinfection to investigate its ability to control photoreactivation. It was found that photoreactivation occurred for all UV doses tested and the increase in bacteria numbers ranged from 0.04 to 1.35 log10. However, the degree of photoreactivation decreased with increased UV doses. Chloramination experiments revealed that the addition of 0.5 mg/l of monochloramine resulted in suppression of photoreactivation for 1 hour only. An increased monochloramine dose of 1 mg/l was found to prevent photoreactivation for the entire duration of the experiment. The results of this study have shown that photoreactivation occurs even after MP UV disinfection, although it is of a lesser extent at higher UV doses. This study has also established that secondary chloramination can effectively suppress and eliminate photoreactivation with a chloramine dose of 1 mg/l.     

Wiener models of direction-dependent dynamic systems

Analysis of systems with direction-dependent dynamics is currently limited to cases in which the dynamics in the two directions of the output are first order; results for such systems have been published for both pseudo-random maximum-length binary (MLB) and inverse-repeat maximum-length binary (IR-MLB) inputs. These relatively limited analytical results make it useful to examine alternative ways of modelling such systems and in this paper, Wiener models are considered for this purpose. Methods for optimising the Wiener model parameters by matching the system and model cross-correlation functions, outputs, and discrete Fourier transforms of the outputs are considered, and the results are compared. These methods are also applied to a first-order direction-dependent system with a maximum-length ternary (MLT) input, for which no analytical results are currently available, and to a second-order system with an IR-MLB input.     

在高温,高压,氢环境中21／4Cr—1Mo钢及其焊接接头KIH的测试

采用恒位移试验方法，在高温、高压、氢环境中用ＷＯＬ试样测试了２１４Ｃｒ－１Ｍｏ钢及其焊接接头的应力腐蚀门限应力强度因子ＫＩＨ。试验结果表明：采用恒位移试验方法测试高温、高压、氢环境中２１４Ｃｒ－１Ｍｏ钢及其焊接接头的ＫＩＨ是可行的。     

Surface modification and functionalization of electroactive polymer films via grafting of polyelectrolyte,polyampholyte and polymeric acids

Films of electroactive polymers, such as polyaniline (PAN) in its emeraldine base form, and poly(3-alkylthiophene), poly(3-hexylthiophene) (P6TH), poly(3-octylthiophene) (P8TH), and poly(3-dodecylthiophene) (P12TH) can be readily functionalized via thermal or near ultraviolet-light-induced surface graft copolymerization with monomers of polyelectrolyte, polyampholyte and polymeric acids. The monomers used in the present work include dimethyl sulphate quaternized dimethylamino-ethylmethacrylate (DMAEM·C₂H₆SO₄), 3-dimethyl(methacryloyloxyethyl)ammonium propane sulphonate (DMAPS), acrylic acid (AAc) and a sodium salt of styrene sulphonic acid (NaSS). The surface structures and compositions of the electroactive polymer films after functionalization via graft copolymerization were characterized by angle-resolved X-ray photoelectron spectroscopy. Graft copolymerization of poly(3-alkylthiophene) films, but not PAN films, with the hydrophilic monomers readily results in a stratified surface microstructure arising from the migration of the hydrophilic graft chains beneath a thin surface layer which is much richer in the substrate chains. On the other hand, graft copolymerization of PAN films with AAc and NaSS readily gives rise to a self-protonated (and thus conductive) surface structure.     

流动微量量热法研究阴离子表面活性剂在油砂表面的吸附

用流动微量量热法研究了十二烷基硫酸钠(SDDS)和十二碳羧酸钠(SL)在克拉玛依油田九区和乌尔禾区油砂上的吸附,简要地计论了吸附机理。所得实验结果表明,SL 在油砂上的吸附强度比 SDDS 的要大,在相当低的浓度下即可迟到饱和吸附。     

Dynamic oxide voltage relaxation spectroscopy

A new method for trap characterization of oxidized silicon is described. The Dynamic Oxide Voltage Relaxation Spectroscopy (DOVRS) is an improved version of the formerly proposed Oxide Voltage Relaxation Spectroscopy (OVRS) technique which applies a periodic long duration constant current for tunneling injection. It has been demonstrated that the new technique can be used not only to separate and identify the oxide trap from interface trap, but also to separate and determine the centroid from the oxide trap density generated in the MOS system by the tunneling current stress. In the pulse constant current mode, the OVRS measurement can be completed instead of using the double current-voltage technique. Thus the new method results in more accurate and quicker measurements of the oxide trap centroid. Analytical expressions for computing the paramaters of the interface and oxide traps are derived. The effect of the channel carrier mobility on the spectroscopy is also considered. Two types of oxide and two types of interface traps were observed at a pulse constant Fowler-Nordheim current stress by the new method of DOVRS     

Expert system application for the loading capability assessment oftransmission lines

This paper describes the application of an expert system for the evaluation of the short-term thermal rating and temperature rise of overhead conductors. The expert system has been developed using a database and Leonardo expert system shell which is gaining popularity among commercial tools for developing expert system applications. The expert system has been found to compare well when evaluated against site tests. A practical application is given to demonstrate the usefulness of the expert system developed     

Gelling of alginate fibres

Equipment was developed to measure the time for complete gelling of sodium alginate fibres in calcium chloride solution, taken as the time to achieve maximum tensile strength. The effects of fibre diameter, alginate concentration, alginate composition and calcium chloride concentration on gelling time were investigated. A diffusional model, developed to predict the gelling time, agreed with experimental results except for the effect of calcium ion concentration which was modelled empirically.