Temperature Profile of Anatase-TiO2Powder Compact during Microwave Heating

Anatase-TiO₂ cylindrical pellets were microwave sintered and partially transformed to rutile-TiO₂.The rutile concentration profile was determined as a function of location within the pellet. The rutile distribution in the microwavesintered pellets was different from that in pellets sintered by conventional fast firing. Temperature profiles within the pellets were estimated using the irreversible nature of the anatase-rutile transformation. The estimated temperature profile within each pellet was not uniform. In the axial direction, maximum temperature occurred in the middle of the pellet. In the radial direction, maximum temperature occurred at 1 mm below the surface of the cylinder wall. Analysis of the temperature profile indicated that, although heat flow occurred in the microwave-sintered pellet, the temperature profile did not change during a microwave exposure of 5–90 min.     

DX centers in AlxGa1-xAs bulk alloy,AlAs/GaAs ordered,and disordered superlattices

Properties of theDX centers in Al_0.5Ga_0.5As bulk alloy (b-AL), (AlAs)₂ (GaSa)₂ ordered superlattice (o-SL) and (AlAs) _m (GaAs) _n disordered superlattice (d-SL) (m = 1, 2, 3,n = 1, 2, 3) with the same macroscopic composition were measured and compared. By deconvolution of deep level transient spectroscopy (DLTS) spectrum due to theDX center, we have found a decrease in the number of separate peaks in DLTS spectrum in an intentionally atomic ordered arrangement. Visiting Scholar of the Japan Society for the Promotion of Science. On leave from Department of Electrical Engineering, San Jose State University, San Jose, California 95192-0084, USA.     

Direct contact melting of porous material

The direct contact melting of a porous material is investigated experimentally and analytically. The phase change material (PCM) is made of fine ice particles of a nearly uniform diameter, which is changed as a parameter. In the analysis, two models are proposed. One is calculated as the direct contact melting of a monolithic sample and another is treated as an assembly of the direct contact melting of the individual particles. As a result, it was found that the heat flux increased with the diameter, due to increase of permeability in a case of small diameter. But, in a case of large diameter, the heat flux decreased as the particle diameter increased because the direct contact melting occurred independently for the individual particles.     

High-accuracy bench mark solutions to natural convection in a square cavity

A fourth-order high-accuracy finite difference method is presented for the bouyancy-driven flow in a square cavity with differentially heated vertical walls. The two bench mark solutions against which other solutions can be compared were obtained. The present solution is seemed to be accurate up to fifth decimal. The proposed scheme is stable and convergent for high Rayleigh number, and will be applicable to general problems involving flow and heat transfer, especially in three dimensions.List of symbols a thermal diffusivity - g gravitational acceleration - h mesh length in the x-direction - k time step - L side length of cavity - Pr Prandtl number - Ra Rayleigh number = gTL ³/a - t time - T _c, T _h surface temperatures (see Fig. 1a) - T temperature - T temperature difference = T _h - T _c - u, v velocity in the x and y directions, respectively - x, y coordinates - x, y mesh lengths in the x- and y-directions, respectively Greek symbols volumetric expansion coefficient - kinematic viscosity - stream function - vorticity     

Formation and Crystallization of Yttrium Aluminosilicate Glasses Containing Calcium Oxide

Formation of yttrium aluminosilicate glasses containing calcium oxide from batches melted at 1550°C was investigated. Densities and thermal expansion coeflcients were measured for some glasses. In a specific compositional region, crystals with a needlelike habit were observed in the glass matrix. A crystal in the form of a tubular hexagonal prism was identified as Ca₄Y₆0(Si0₄)₆.     

Dynamic Mechanical Properties and Adhesive Strengths of Emulsion Polymer by Power Feed Technique, I

Dynamic mechanical properties and adhesive strengths of power feed copolymer and random copolymer synthesized using styrene or methyl methacrylate and n-butyl acrylate were investigated. Although the two systems were synthesized from the same raw materials, power feed copolymer had a very broad transition compared with random copolymer. This fact was explained by the fact that the system synthesized through power feed method was an alloy of copolymers which are a continuous series from monomer A rich copolymers to monomer B rich copolymers. The dynamic mechanical behavior of film cast from solution was almost the same as that of emulsion film, which indicated more extensive application of power feed copolymer. In the P(nBA/St) system, power feed copolymer maintained its adhesive strengths over a wide temperature range compared with random copolymer. The absolute value, however, was not so high. This was due to the low cohesive strengths of the films.     

New type of tin support for hydroprocessing catalyst

TiN supported molybdenum sulfide catalysts showed much higher activity for cleavage of C-C bonds than oxide supported molybdenum sulfide catalysts, indicating the possibility of a new generation of supports for hydroprocessing catalysts.     

Critical temperature for production of MAG by esterification of different FA with glycerol using <Emphasis Type="Italic">Penicillium camembertii</Emphasis> lipase

Production of MAG by a lipase-catalyzed reaction is known to be effective at low temperature. This phenomenon can be explained by assuming that synthesized MAG are excluded from the reaction system because MAG, which have low m.p., are solidified at low temperatures. Consequently, MAG are efficiently accumulated and do not serve as the precursor of DAG. If this hypothesis is correct, the critical temperature for MAG production, defined as the highest temperature at which DAG synthesis is repressed, should depend on the m.p. of the MAG. Esterification of FFA with glycerol using Candida rugosa, Rhizopus oryzae, and Penicillium camembertii lipases produced MAG efficiently at low temperatures. However, Candida lipase showed very low esterification activity at high temperatures (>20°C), and Rhizopus lipase produced not only MAG but also DAG even at low temperatures. Meanwhile, P. camembertii lipase catalyzed synthesis of MAG only from FFA and glycerol at low temperatures, although the enzyme catalyzed synthesis of DAG from MAG in addition to synthesis of MAG at high temperatures. We thus studied the effect of temperature on esterification of C₁₀−C₁₈ FFA with glycerol using Penicillium lipase as a catalyst and determined the critical temperatures for production of MAG. The critical temperature for production of each MAG showed a linear correlation with m.p. of the MAG, which supported the hypothesis. In addition, because the m.p. of MAG are estimated from that of the constituent FA, the optimal temperature for production of MAG can be predicted from the m.p. of the FFA used as a substrate.