Switching characteristics of vacuum gap switch employing UV‐laser triggering

The switching time and arc‐ignition probability of a sustained main discharge in a laser trigger vacuum gap were measured. The third harmonic beam of an Nd:YAG pulse laser (wavelength 355 nm, energy 5 mJ/pulse, power density 4 × 10⁷ W/cm²) was used to trigger the gap. The main electrodes 85 mm in diameter were made of oxygen‐free copper. The gap length was 1.6 mm and the experimental chamber was evacuated to about 1.3 × 10⁴ Pa by a turbomolecular pump. The UV beam from the laser was focused at normal incidence onto the grounded cathode. The switching time decreased and the arc‐ignition probability increased with increasing applied voltage. The switching time was 326 ns at 15 kV with a circuit inductance of 107 μH. Its jitter was 24.8 ns. The advantageous results obtained with the UV beam are compared to the previously reported data on triggered vacuum gaps. © 2000 Scripta Technica, Electr Eng Jpn, 132(3): 8–13, 2000     

Complex impedance and admittance of a silver-conducting glass

From the analysis of complex impedance and admittance data of (Agl)₇₅(Ag₄P₂O₇)₂₅ glass, an Ag⁺-ion conductor, it was revealed that the sample can be approximated by a seriesRC ₁ circuit at high temperature, with the capacitorC ₁ arising from the charge-carrier depleted region near the anode which develops as conduction proceeds, and by a parallelRC ₂ circuit at low temperature, with the capacitorC ₂ arising from the saturated value for ionic polarization of, say, the silver-iodine pairs as well as from the relaxation effect of the Ag⁺ ions for conduction. TheC ₁ andC ₂ values were found to be almost temperature-independent at peak frequencies of the distorted semicircles in respective complex planes, with the ratioC ₁/C ₂ as large as 10⁴.     

Corneal critical barrier against the penetration of dexamethasone and lomefloxacin hydrochloride: evaluation by the activation energy for drug partition and diffusion in cornea

The cornea is a solid barrier against drug permeation. We searched the critical barrier of corneal drug permeation using a hydrophobic drug, dexamethasone (DM), and a hydrophilic drug, lomefloxacin hydrochloride (LFLX). The activation energies for permeability of DM and LFLX across the intact cornea were 88.0 and 42.1 kJ/mol, respectively. Their activation energies for permeability across the cornea without epithelium decreased to 33.1 and 16.6 kJ/mol, respectively. The results show that epithelium is the critical barrier on the cornea against the permeation of a hydrophobic drug of DM as well as a hydrophilic drug of LFLX. The activation energy of partition for DM (66.8 kJ/mol) was approximately 3-fold larger than that of diffusion (21.2 kJ/mol). The results indicate that the partition for the hydrophobic drug of DM to the corneal epithelium is the primary barrier. Thermodynamic evaluation of activation energy for the drug permeation parameters is a good approch to investigate the mechanism of drug permeability.     

Profile structure of magnetic flux lines in type-II superconductor from a rectangular electron hologram

Profile magnetic configuration of a quantized flux line and flux-line lattice penetrating a type-II superconductor thin foil, niobium, was observed by electron holography and Lorentz microscopy using a 300 kV field-emission electron microscope. Each single flux line was distributed periodically as lattice structure in the mixed state just below its critical temperature of 8.5 K, while at low temperature of 5 K the flux lines were weakly bound as bundles. In order to observe the flux-line distribution over a wide area, discrete Fourier transform reconstruction in the holography was extended for a rectangular area without loss of information and data precision.     

Erosive Wear Mechanism of New SiC/SiC Composites by Solid Particles

A solid-particle erosive wear test by impinging silicon carbide (SiC) powders was carried out at room temperature over a range of median particle sizes of 425–600 μm, speed of 100 m/s and impact angle of 90° and assessed by wear measurements and scanning electron microscopy. Erosive wear behaviour was examined on newly fabricated nano-powder infiltration and transient eutectoid (NITE) SiC/SiC composites and two commercial composites by the chemical vapour infiltration (CVI) and NITE fabrication route. Microstructural observation was performed to examine the correlation between erosive wear behaviours and fabrication impurities. Conspicuous defects were observed in the prototype materials as the forms of porosity, fibre deformation, residual oxide, pyrolytic carbon (PyC) deformation, PyC cleavage, among others. Erosive wear behaviour was rather serious in the prototype of fabricated composites, which employ pre-SiC fibre and phenolic resin. Two dominant erosive wear mechanisms were observed: delamination of constituents, mainly caused by erosive crack propagation, and fragmentation and detachment of constituents, which usually resulted from erosive impact. A unit size of delamination was the most decisive factor affecting wear volume. The bonding strength of each constituent was mostly affected by various forms of porosities. Therefore, the fundamental cause and subsequent results must be carefully elucidated. The correlation of microstructural defect and wear behaviour was investigated with the aim of reducing dominant wear by improving fabrication conditions. The final product of the cost-effective composite had a 2.5-fold higher resistance than the commercial CVI composite. Consequently, by controlling fabrication impurities, we have been successful in developing and improving a new fabrication technique; consequently, the known defects are rarely observed in final product. A schematic wear model of erosive wear mechanisms is proposed for the newly fabricated SiC/SiC composites under particle erosion.     

Influence of DLC coating thickness on tribological characteristics under sliding rolling contact condition

Diamond-like-carbon (DLC) coating of thickness 3 and 10 μm were developed with and without radical nitriding pretreatment on steel rollers and spur gear pair. The friction coefficient and wear amount were evaluated under sliding rolling contact condition in vacuum and under oil lubrication. Delamination of coatings was observed at the interface of the substrate. The wear resistance of coatings improved with the thickness of the coating. In vacuum both the roller and the gear pair of 10 μm coating thickness with radical nitriding showed identical wear behavior. The radical nitriding seemed to enhance the life of DLC coatings.     

Phase transition of 2,3-O-methylcellulose

Summary In this work, a series of 2,3-O-methylcellulose (MC) with different DS value were prepared. Its phase transition behavior in aqueous solution was studied in terms of DS value, concentration and molecular weight. The the following conclusions were obtained. (1) All the 2,3-O-MC samples show no sol-gel transition in aqueous solution despite the molecular weight. (2) No phase separation was observed for the 2,3-O-MCs with a DS value lower than 1.0, even when the temperature was raised to 95°C. (3) The precipitation temperature is surprisingly different between 2,3-O-MCs. and other MCs possessing comparable total DS value. (4) The precipitation temperature of 2,3-O-MCs depends on the molecular weight rather than on the concentration. Received: 3 February 1998/Revised version: 30 March 1998/Accepted: 11 April 1998     

Enhancement of low density lipoprotein binding to both low density lipoprotein receptor-positive and- negative cells by tetracycline antibiotics

Some tetracycline (TC) antibiotics, including TC and anhydrotetracycline, have been found to enhance specific binding of low density lipoprotein (LDL) to both LDL receptor-positive and-negative cells at relatively higher concentrations. When incubated at 37°C, the ability of LDL receptor-negative human fibroblasts to bind ¹²⁵I-LDL was increased from<2 to 45 ng/mg by 170 μM TC. In normal human fibroblasts and Hep G2 cells, ¹²⁵I-LDL binding was elevated 1.4- to 2-fold by 113 μM TC. The ¹²⁵I-LDL binding in the presence of TC was diminished by both heparin and EDTA. The enhancement by TC was not observed when ¹²⁵I-LDL binding was assayed at 4°C. TC enhanced LDL binding to paraformaldehyde-fixed Hep G2 cells, excluding LDL receptor induction in the mechanism. These results demonstrated that TC enhanced cellular LDL binding through a process not involving functional LDL receptors.     

Fatigue life estimation of steel using laser speckle sensor

We investigated a method to evaluate fatigue damage of steels without contact using a laser speckle sensor. In the earlier stage of fatigue in steels, slipbands are produced on the surface and the slipband density increases as fatigue damage progresses. When a laser illuminates the surface of the fatigued steel, light intensity distribution of the laser speckle pattern caused by the reflected light changes depending on the change of surface properties caused by slipbands. Width of the speckle pattern broadens correspondingly to spatial frequency distribution of the surface and thus it is presumed that speckle pattern broadens with increase of slipband density. The method presented in this paper is based on this phenomenon. In this study, we observed change of the speckle pattern during fatigue loading. We propose a method to estimate fatigue life by observing change in the speckle pattern depending on number of loading cycles in the earlier stage of fatigue before crack initiation.     

Geosynthetic-sheet pile reinforced foundation for mitigation of earthquake and tsunami induced damage of breakwater

Earthquake and tsunami impose great threats on the stability of a breakwater. Foundation of the breakwater is weakened by these forces, and it may result in collapse of the breakwater. Lateral flow of seabed soils take place beneath the breakwater, and excess pore water pressure is generated in the foundation by an earthquake that precedes tsunami. These factors may lead to excessive settlement and horizontal displacement of the breakwater. Tsunami introduces additional instability to the deformed breakwater. Due to water level difference between seaside and harborside of the breakwater during a tsunami, seepage occurs through its foundation, and it may cause pipping of seabed soils. Tsunami induced scouring of mound is also a big problem for the stability of the breakwater foundation. Finally, these result in failure of the breakwater foundation. Due to failure of its foundation, the breakwater may collapse and cannot block the tsunami. It results in entering of the tsunami in coastal areas. In order to make a breakwater resilient against earthquake and tsunami induced damage, reinforcing countermeasures were developed for foundation of a breakwater. Geogrid, gabions and sheet piles were used for reinforcing a foundation model. The effectiveness of the model is evaluated through physical modeling for mitigating the earthquake and tsunami induced damage. Shaking table tests were performed to determine the effectiveness of the reinforced model under different earthquake loadings. Tsunami overflow test was conducted on the same deformed model in order to see the effects of tsunami on the model. Comparisons were made between the unreinforced and reinforced foundations, and it was observed during the tests that the reinforced foundation performed well in reducing the damage of the breakwater brought by the earthquake and tsunami. Overall, this study is useful for practice engineering, and the reinforced foundation model can be adopted for designing a breakwater foundation to reduce damage triggered by an earthquake and tsunami in the future.