DOPO‐Based Phosphorus‐Containing Methacrylic (Co)Polymers: Glass Transition Temperature Investigation

A two‐step synthetic procedure is designed for preparing new flame‐retardant methacrylic monomers containing 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) as a substituent side group. DOPO and methacrylate moieties are linked by linear aliphatic hydrocarbon spacers (3 to 11 carbon atoms). Copolymerization with methyl methacrylate is carried out leading to copolymers containing between 2 and 10 wt% phosphorus. All homo‐ and copolymers exhibit a unique glass transition temperature (T_g ). A new group contribution for DOPO‐based substituent is extracted that leads to reasonable estimations of T_g s of other published polymers. The Fox equation provides a good estimation of T_g s for most copolymers and for physical blends of poly(methyl methacrylate) (PMMA) and DOPO. When using monomers having three and four carbon atoms in the hydrocarbon spacer, the T_g of copolymers remains close to that of PMMA over a wide range of composition.     

How operators make use of wide-choice adaptable automation: observations from a series of experimental studies

The present paper is concerned with the design of adaptable automation. It analyses the aggregated data from five experiments (N = 154) to examine which automation levels operators prefer, how often they switch between them, and whether performance is associated with frequent switching or the automation levels being used. Using wide-choice adaptable automation (i.e. up to six levels were offered), the experiments were conducted using a PC-based simulation of a complex work environment. The results showed that about 95% of operators had a clearly preferred automation level, which they used for more than 50% of the time. They strongly preferred intermediate automation levels over levels at the higher and lower ends of the scale. Most operators switched rarely between levels and when they did, they usually made small adjustment rather than large changes. Several implications for the design of adaptable automation were derived from the empirical data.     

Noise Feedback Coding Revisited： Refurbished Legacy Codecs and New Coding Models

Noise feedback coding(NFC) has attracted renewed interest with the recent standardization of backward-compatible enhancements for ITU-T G.711 and G.722.It has also been revisited with the emergence of proprietary speech codecs,such as BV16,BV32,and SILK,that have structures different from CELP coding.In this article,we review NFC and describe a novel coding technique that optimally shapes coding noise in embedded pulse-code modulation(PCM) and embedded adaptive differential PCM(ADPCM).We describe how this new technique was incorporated into the recent ITU-T G.711.1,G.711 App.III,and G.722 Annex B(G.722B) speech-coding standards.     

Evaluation of temperature field and heat flux by inverse analysis during steel strip rolling

Knowledge of the temperature field in the roll is a critical factor of modern, high-speed rolling mills. In this paper, an inverse analytical method is developed to determine the temperature field and especially the temperature (and heat flux) at the surface of the roll by measuring the temperature with a thermocouple (fully embedded) at only one point inside the roll. Iterative methods are not studied because short computation times are desired. Some assumptions are done to resolve analytically the unsteady heat equation, taking into account the restrictions of the measurement system (e.g., measurement according to successive times). The solution is validated by comparing the outputs of the method and prescribed analytical temperature fields. Good agreement is obtained. Noise sensitivity is estimated by adding artificial random numbers to the inputs. Good accuracy is observed. A 10% error of the temperature sensor depth is also considered and does not compromise the method. On the other hand, the computation time (around 0.05 s by cycle) is studied to rapidly optimise the industrial parameters during the rolling process.     

Design of a low-density wood-cement particleboard for interior wall finish

Gypsum boards form a very large part of the building walls and ceilings finishing market. However, they have poor screw-withdrawal resistance, low hardness and are highly sensitive to moisture. The objective of this study was to determine whether it is possible to make wood-cement particleboards of the same density as gypsum boards while avoiding these drawbacks.Wood-cement particleboards were made by pouring the wood-cement paste in a mould. This was made possible by adding a viscosity modifying mixture to the mixing water and a set accelerating mixture to improve wood/cement compatibility. The mechanical properties and surface quality of the wood-cement particleboards were improved by using, on the board surfaces, paper sheets that were the same as those used on gypsum boards.The average specific gravity of the wood-cement particleboards was the same as gypsum boards, at 0.7. The average bending modulus of rupture obtained for the wood-cement particleboards was 10 MPa in the finishing paper principal direction and 5 MPa in the other direction compared to 5.5 MPa and 1.6 MPa respectively for gypsum boards. The average screw-withdrawal resistance of wood-cement particleboards was 570 N, that is, 1.7 times higher than for gypsum boards.     

Analysis of muscle length effect on an S type motor-unit fractional multi-model

Muscle models are useful in bio-inspired robotic, because they allow to reproduce accurately natural motion. When they are used for robotic issue, they need to be compact and embeddable. The non-integer model order has the advantage to ensure a parametrical parsimony that permits to implant it easily on an embedded system. Thus, a fractional multi-model of muscle was identified and presented in later paper. This model is able to predict the response of a motor unit to an electrical stimulation, considering isometric contractions (that is to say, muscle length is constant). There are three different physiological types of motor unit (FR, FF, and S). The aim of this work is to study muscle length impact on the multi-model and the limitations of the linear multi-model. Previous paper was published using FR type motor unit. In this paper, the results of the study using S type motor unit are presented.     

Numerical assessment of springback for the deep drawing process by level set interpolation using shape manifolds

In this paper, we introduce an original shape representation approach for post-springback characterization based on the automatic generation of parameterized level set functions. The central idea is the concept of the shape manifold representing the design domain in the reduced-order shape-space. Performing Proper Orthogonal Decomposition on the shapes followed by using the Diffuse Approximation allows us to efficiently reduce the problem dimensionality and to interpolate uniquely between admissible input shapes, while also determining the smallest number of parameters needed to characterize the final formed shape. We apply this methodology to the problem of springback assessment for the deep drawing operation of metal sheets.     

New quadratic solid–shell elements and their evaluation on linear benchmark problems

This paper is concerned with the development of a new family of solid–shell finite elements. This concept of solid–shell elements is shown to have a number of attractive computational properties as compared to conventional three-dimensional elements. More specifically, two new solid–shell elements are formulated in this work (a fifteen-node and a twenty-node element) on the basis of a purely three-dimensional approach. The performance of these elements is shown through the analysis of various structural problems. Note that one of their main advantages is to allow complex structural shapes to be simulated without classical problems of connecting zones meshed with different element types. These solid–shell elements have a special direction denoted as the “thickness”, along which a set of integration points are located. Reduced integration is also used to prevent some locking phenomena and to increase computational efficiency. Focus will be placed here on linear benchmark problems, where it is shown that these solid–shell elements perform much better than their counterparts, conventional solid elements.