Ionoluminescence decay measured with single ions

A new ion beam analysis-based, single ion technique called the time to first photon has been developed to measure the decay of the luminescence signal of phosphors. Such measurements are currently needed to study luminescence decay mechanisms following high-density excitations and to identify strongly luminescent phosphor coatings with short lifetimes for ion photon emission microscopy (IPEM). The samples for this technique consist of thin phosphor layers placed or coated on the surface of PIN diodes. Single ions from an accelerator strike this sample and simultaneously create ion beam induced luminescence (IBIL) from the phosphor that is measured by a single-photon-detector, and an ion beam induced charge collection (IBICC) signal in the PIN diode. In this case, the IBICC signal provides the start pulse and the IBIL signal the stop pulse to a time to amplitude converter. It is straightforward to show that this approach also measures a signal proportional to activity versus time with an accuracy of 5% as long as the number of detected photons per ion is less than 0.1, which usually requires the use of absorbers for the IBIL detector or electronic discrimination for the IBIL signals. Details of the new analysis are given together with examples of luminescence decay measurements of several ceramic phosphors being considered to coat IPEM samples. IPEM is currently being developed at Sandia National Laboratory (SNL), the University of North Texas in Denton, and the Universities and INFN of Padova and Torino.     

Rapid determination of the fracture toughness of metallic materials using circumferentially notched bars

Three types of material whose fracture toughness tests were previously performed by using circumferentially notched bars, namely (1) a dual-phase steel with three different morphologies; (2) an Al-Zn-Mg-Cu-wrought alloy; and (3) Al-Si-cast alloys with three different Si contents, were investigated in terms of accuracy and reliability of the testing method. Also, the advantages of using circumferentially notched bars for fracture toughness determination of metallic materials were discussed. With the help of stress concentration factors, which are associated with the bluntness of the notch, correction factors for the fracture toughness calculations are derived. The corrected fracture toughness values are found to be close to the uncorrected ones, implying that the testing procedure is reliable.     

Electroplating of nickel-cadmium alloys from alkaline solutions

The electroplating of Ni-Cd alloy coatings was carried out from alkaline baths (pH 10). For comparison, electroplating of the parent metals, Ni and Cd, was performed individually under the same conditions. The cathodic current efficiency for codeposition was high and decreased with increasing current density. The codeposition process is an anomalous type of plating with Cd being the preferentially deposited metal. The Ni content in the deposits increased with increasing current density. This increase in Ni content improves the corrosion resistance and microhardness of the deposits. X-ray diffraction analysis showed that the deposits consist of a mixture of Ni, β, γ, γ¹ phases.     

Compact WLAN disc antennas

A novel conical beam patch antenna design, suitable for local area network applications, uses a central cylindrical connection from the disc to ground to achieve a large reduction in resonant size. Results on efficiency, bandwidth, and pattern are reported for several prototypes.     

An analytical model for high electron mobility transistors

In this paper we present a new model for HEMT's which is based on a single analytical function that describes the electron concentrations in the two dimensional electron gas and in the AlGaAs layer. Besides accounting for the AlGaAs conduction, the model includes the effect of mobility degradation, channel length modulation in the saturation region and the series resistances R_S and R_D. The model results in closed form expressions for the current, transconductance, output conductance and gate capacitance. Finally, the theoretical predictions of the model are compared with the experimental data and shown to be in good agreement over a wide range of bias conditions     

Electrical properties of tri-n-butyl tin acrylate-methylmethacrylate copolymers

The copolymerization of tri-n-butyl tin acrylate (TBTA) with methylmethacrylate (MMA) has been investigated in dioxane. The composition of these copolymers was determined quantitatively by ¹H nuclear magnetic resonance (NMR) spectroscopy. The tin contents were estimated by gravimetric as well as thermogravimetric techniques (TGA). The reactivity ratio of such copolymers was estimated by application of the Kelen-Tudos method. The dielectric properties of the copolymers have been studied over a frequency range of 100–50 kHz at different temperatures from 20 to 70°C. The electrical conductivity for such copolymers was also measured. The results are interpreted in terms of the tin content of the copolymers.     

Dynamic bandwidth allocation for quality-of-service over Ethernet PONs

Ethernet-based passive optical network (EPON) technology is being considered as a promising solution for next-generation broadband access networks due to the convergence of low-cost Ethernet equipment and low-cost fiber infrastructures. A major feature for this new architecture is the use of a shared transmission media between all users; hence, medium access control arbitration mechanisms are essential for the successful implementation of EPON: i.e., to ensure a contention-free transmission and provide end users with equal access to the shared media. We propose to use the multipoint control protocol defined by the IEEE 802.3ah task force to arbitrate the transmission of different users, and we present different dynamic bandwidth allocation (DBA) algorithms to allocate bandwidths effectively and fairly between end users. These DBA algorithms are also augmented to support differentiated services, a crucial requirement for a converged broadband access network with heterogeneous traffic. We show that queueing delays under strict bandwidth allocation algorithms result in an unexpected behavior for certain traffic classes, and we suggest the use of DBA with appropriate local queue management to alleviate this inappropriate behavior. We conduct detailed simulation experiments to study the performance and validate the effectiveness of the proposed protocols.     

Synthesis and structural characterization of new defect pyrochlore type AxLnySb2O6+z antimoniates (0<x, y, z<1; A = Rb, Cs, Tl; Ln = Eu, Gd, and Y) prepared by coprecipitation

New cubic defect pyrochlore type A_xLn_ySb₂O_6+z antimoniates (0<x,y,z<1; A=Rb, Cs, Tl; Ln=Eu, Gd, and Y) (space group Fd3m) were prepared by calcination in air at 650 °C of compositions obtained by a coprecipitation method. Their crystal structures were refined by the Rietveld procedure and further confirmed by X-ray absorption spectroscopy (EXAFS) experiments. Refinements of the X-ray powder diffraction data show a partial and statistical occupation of the 8b site by alkaline or thallous ions and oxygen and lead to values close to 0.33 for the only refinable positional x parameter of the 48f oxygenated site.