Formation and elimination of surface ion milling defects in cadmium telluride,zinc sulphide and zinc selenide

The nature of damage produced by low energy Ar⁺ ion and Ar atom milling in the II–VI semiconductors CdTe, ZnS and ZnSe is studied in detail by conventional and high resolution transmission electron microscopy. It is demonstrated that the damage consists of dense arrays of small dislocation loops near to each milled surface. When ion or atom milling of this type is used for thin specimen preparation prior to microscopy the loop arrays can seriously obscure images and so complicate their interpretation. This problem concerning the presence of artifactual defects can be greatly reduced by the use of reactive I⁺ ion milling for specimen thinning and, in the case of CdTe, spurious dislocation loop formation can be completely suppressed.     

Variations in Spectral Slope in Lake Taihu,a Large Subtropical Shallow Lake in China

Spectral slope (S), describing the exponential decrease of the absorption spectrum over a given wavelength range, is an important parameter in the study of of chromophoric dissolved organic matter (CDOM) dynamics, and also an essential input parameter in remote sensing models. Furthermore, S is often used as a proxy for CDOM composition, including the ratio of fulvic to humic acids and molecular weight. The relative broad range in S values reported in the literature can be explained by the different spectral ranges and fitting methods used. A single exponential model is used to fit the S values for 17 investigations involving 458 samples in Lake Taihu from January to October in 2004. The average S value was 15.18 ± 1.39 μm⁻¹ for the range of 280–500 nm, which fell within the range reported in the literature. The frequency distribution of S value basically obeyed a normal distribution. Significant differences in S values between summer and other seasons showed that phytoplankton degradation was one of the important sources of CDOM in summer, whereas CDOM mainly came from the river input in other seasons. Furthermore, the estimated S value decreased with increasing wavelength range used in regression. The maximum and minimum values derived from the regression were 17.89 ± 1.25 μm⁻¹ and 13.62 ± 2.11 μm⁻¹ for the wavelength ranges of 280–380 nm and 400–500 nm, respectively, a decrease of 23.9%. S values significantly decreased with the increase of CDOM absorption coefficients. CDOM absorption coefficients could be more appropriately estimated from exponential model introducing the variation of S with absorption coefficients, making them useful for a remote sensing bio-optical model of Lake Taihu. DOC-specific absorption coefficient a*(λ) and the parameter M describing molecular size of the humic molecules could also be used as a proxy for the sources and types of CDOM. A general relationship was found between S and a*(λ), and M values. S increased with the decrease of DOC-specific absorption coefficient and the increase of M corresponding to the decrease of molecular weight.     

Effects of Contaminants on Toxicity of the Lampricides TFM and Bayer 73 to Three Species of Fish

Waters in the Great Lakes basin contain more than 400 contaminant chemicals that potentially affect fishery resources, commerce, and human inhabitants. We determined in the laboratory the effects of selected contaminants on the toxicity of the widely used lampricides TFM (3-trifluoromethyl-4-nitrophenol) and Bayer 73 (2′,5-dichloro-4′-nitrosalicylanilide) to three species of fish—rainbow trout (Salmo gairdneri), white sucker (Catostomus commersoni), and fathead minnow (Pimephales promelas). The fish were exposed to paired mixtures of lampricides and selected contaminants in standardized, acute static toxicity tests to determine the resulting type of response—less than additive, additive, or greater than additive (synergistic). As expected, the toxicities of combinations of lampricides with organic pesticides, metal, industrial or municipal pollutants, and tannic acid were mostly additive. However, the toxicity of a combination of TFM, Delnav, and malathion was synergistic, and extremely small quantities of each chemical became lethal when mixed. The concentration that produced 50% mortality was 1.64 mg/L for TFM alone but only 0.041 mg/L for TFM with the pesticides. Toxicities of the pesticides in the combination also increased commensurately. The triple combination of chemicals produced extraordinary synergism and effectively demonstrated the hazards that may result if certain chemical combinations occur in the aquatic environment. However, synergism is not the only kind of toxic action that produces hazards to aquatic organisms. All three types of toxic action are of concern because toxic units produced by contaminant chemicals add to the toxic units of applied management chemicals. Since the toxicity of the majority of chemical combinations is simply additive, this cumulative toxic action contributes more total units to aquatic environments than the extreme actions of less than additive and synergism. The toxicity of the lampricide TFM, as well as other management chemicals, is reinforced by the presence of any contaminant that contributes additional units of toxicity. Therefore, all types of cumulative toxic action should be of concern to people and agencies involved with protecting the environment.     

Evaluation of hardenability of alloyed white irons

A method for evaluating the hardenability of wear-resistant complexly alloyed white irons based on transition from a homogeneous austenite structure to a heterogeneous austenite-carbide structure in hardened alloys is developed. The transition occurs with respect to the chemical composition of the austenite matrix with allowance for the effect of carbides. Computation of the hardenability of a homogeneous steel matrix is performed using an earlier-developed mathematical model allowing for the mutual influence of the components dissolved in the austenite. Experimental data and computed results are used to plot a thermokinetic diagram of decomposition of austenite in complexly alloyed white iron. Analysis of the effect of the amount and type of carbides on the hardenability of alloys with austenite-carbide structure is performed. __________ Translated from Metallovedenie i Termicheskaya Obrabotka Metallov, No. 8, pp. 47–51, August, 2007.     

Inverse controller design for fuzzy interval systems

This paper aims at designing and analyzing an inverse controller for stable inversible (minimum phase) fuzzy interval linear and/or multilinear systems. The controller is designed from the fuzzy interval ranges of the system parameters using an /spl alpha/-cut methodology. Indeed, for a given /spl alpha/-cut of the fuzzy system parameters representing an uncertainty level, the control objective can be viewed as maintaining the system output within a tolerance envelope, around the exact trajectory, specified by the degree of preference /spl alpha/ on the fuzzy trajectory. The stability is ensured in the way that the controller restricts the system output divergence within the tolerance envelope. The validity of the proposed method is illustrated by simulation examples.     

Modeling of anaerobic treatment of wastewater in ponds.

A mathematical model to simulate the performance of anaerobic ponds was developed incorporating both settling of particulate components and the biological anaerobic digestion process. The biological activity includes solubilization of particulate organic matter; methanogenesis and the sulphate reduction process. The model considers that an anaerobic pond comprises a series of equal size columns. Each column has three compartments viz. liquid layer, active sediment layer and inert sediment layer. The existence of organic matter and sulphate removal mechanisms both in the bulk as well as sediment layer of the ponds and the exchange of the soluble components between the layers has been included in the model. The model was transferred to a computer program using VisSim Basic software. The model was verified by comparing simulated results with full-scale as well as with laboratory-scale anaerobic pond performance data. A good agreement between the simulated and the observed pond performance was achieved.