Peracetic acid pretreatment of sugarcane bagasse for enzymatic hydrolysis: a continued work

Previous work has shown that the enzymatic hydrolysis of sugarcane bagasse could be greatly enhanced by peracetic acid (PAA) pretreatment. There are several factors affecting the enzymatic digestibility of the biomass, including lignin and hemicelluloses content, cellulose crystallinity, acetyl group content, accessible surface area and so on. The objective of this work is to analyze the mechanism of the enhancement of enzymatic digestibility caused by PAA pretreatment. Delignification resulted in an increase of the surface area and reduction of the irreversible absorption of cellulase, which helped to increase the enzymatic digestibility. The Fourier transform infrared (FTIR) spectrum showed that the absorption peaks of aromatic skeletal vibrations were weakened or disappeared after PAA pretreatment. However, the infrared crystallization index (N.O'KI) was increased. X‐ray diffraction (XRD) analysis indicated that the crystallinity of PAA‐treated samples was increased owing to the partial removal of amorphous lignin and hemicelluloses and probable physical change of cellulose. The effect of acetyl group content on enzymatic digestibility is negligible compared with the degree of delignification and crystallinity. The results indicate that enhancement of enzymatic digestibility of sugarcane bagasse by PAA pretreatment is achieved mainly by delignification and an increase in the surface area and exposure of cellulose fibers. Copyright © 2008 Society of Chemical Industry     

Effects of surfactant/silica and silica/cerium ratios on the characteristics of mesoporous Ce-MCM-41

Using the surfactant CTMABr (cetyltrimethyl ammonium bromide) and cerium(IV) sulfate, mesoporous Ce-MCM-41 molecular sieves were produced under a hydrothermal condition with various surfactant/silica (surfactant/Si) and silica/cerium (Si/Ce) ratios. Changes to the structural traits caused by changing the molar ratios of both surfactant/Si and Si/Ce were investigated. XRD (X-ray diffraction), FT-IR (fourier transform infrared spectroscopy), and SEM (scanning electro microscopy) were used for the characterization of prepared mesoporous samples. Among the tested molar ratios, surfactant/Si ratio of 0.5 and 0.2 showed highest values of d_1 0 0 and intensity, respectively, for the Si-MCM-41. XRD analysis also identified a quintessential hexagonal structure of Ce-MCM-41 for the Si/Ce molar ratio higher than 40 (maintaining the surfactant/Si ratio at 0.2). When cerium content was increased to have the Si/Ce molar ratio of 20, the hexagonal structure of Ce-MCM-41 was collapsed due to the structural stress of substituted cerium. FT-IR results confirmed calcination of Ce-MCM-41 and the incorporation of Ce⁴⁺ ions of cerium sulfate into the silica surface with proper removal of the surfactant. Rod-like shape with rounded edges of the prepared Ce-MCM-41 samples was identified by SEM. These results suggest surfactant/Si ratio of 0.2 and Si/Ce ratio of 40 for the production of Ce-MCM-41 with the highest level of crystallinity.     

Prediction and quality control of the melt index during production of high-density polyethylene

In polyolefin processes the melt index (MI) is the most important control variable indicating product quality. Because of the difficulty in the on-line measurement of MI, a lot of MI estimation and correlation methods have been proposed. In this work a new dynamic MI estimation scheme is developed based on system identification techniques. The empirical MI estimation equation proposed in the present study is derived from the 1 ^st -order dynamic models. Effectiveness of the present estimation scheme was illustrated by numerical simulations based on plant operation data including grade change operations in high density polyethylene (HDPE) processes. From the comparisons with other estimation methods it was found that the proposed estimation scheme showed better performance in MI predictions. The virtual sensor model developed based on the estimation scheme was combined with the virtual on-line analyzer (VOA) to give a quality control system to be implemented in the actual HDPE plant. From the application of the present control system, significant reduction of transition time and the amount of off-spec during grade changes was achieved     

Simultaneous degradation of nitroaromatic compounds TNT,RDX, atrazine,and simazine by Pseudomonas putida HK‐6 in bench‐scale bioreactors

BACKGROUND: Environmental contamination by nitroaromatic compounds such as 2,4,6‐trinitrotoluene (TNT), hexahydro‐1,3,5‐trinitro‐1,3,5‐s‐triazine (RDX), atrazine, and/or simazine (TRAS) generated as waste from military and agricultural activities is a serious worldwide problem. Microbiological treatment of these compounds is an attractive method because many explosives and herbicides are biodegradable and the process can be made cost‐effective. We explored the feasibility of using cultures of Pseudomonas putida HK‐6 for simultaneous degradation of TRAS with the aim of microbial application in wastewater treatment in bench‐scale bioreactors. RESULTS: Experiments were conducted to study the effects of supplemental carbons, nitrogens, and Tween‐80 on the degradation of Ps. putida HK‐6 in media containing TRAS as target substrate(s). The most effective TRAS degradation was shown in the presence of molasses. Addition of nitrogen sources produced a delayed effect for the target substrate(s). Tween‐80 enhanced the degradation of target substrate(s). Simultaneous degradation of these compounds proceeded to completion within the given period. CONCLUSIONS: Ps. putida HK‐6 was capable of growth with TRAS, and the effects of supplements on TRAS degradation and simultaneous TRAS degradation were evaluated in bench‐scale bioreactors. The results of this study have practical applications in the processes of industrial waste stream treatment where the disposal of TRAS may be problematic. Copyright © 2008 Society of Chemical Industry     

Online and Offline Rotary Regression Analysis of Torque Estimator for Switched Reluctance Motor Drives

A new torque estimator for switched reluctance motor (SRM) drives based on 2-D rotary regression analysis is presented in this paper. The proposed torque estimator is composed of a bicubic regressive polynomial as a function of rotor position and input current. The regressive coefficients can be computed offline or online from the torque characteristics acquired either experimentally or from numerical computation. Furthermore, a torque estimation method by taking mutual coupling into consideration is proposed. It can be seen that the estimated and experimentally obtained self-coupling and mutual-coupling torque characteristics are in good agreement with each other. In addition, the dynamic torque waveforms with and without the mutual coupling, estimated by the proposed estimator, are found to be virtually the same as those obtained from the bicubic spline interpolation for SRM drives with single-pulse voltage, hysteresis current chopping, as well as with voltage pulse width modulation control. The success of all the case studies being reported is a good validation of the usefulness and accuracy of the proposed real-time torque estimator that, as described in this paper, can be used to quickly estimate the instantaneous output torque of SRM drives.     

Polyetherimide substrates for future high density optical data storage

Polyetherimide (PEI) substrate for next‐generation high density optical data storage is fabricated and characterized. Cover‐layer incident or first‐surface recording configurations do not require optical properties of the substrate, which are the prerequisite conditions for the conventional material of polycarbonate (PC). Instead of the optical properties, good mechanical properties with a sufficient transcribability are required. Even though PEI has higher glass transition temperature than that of PC, a microscopic transcribability of PEI is comparable with PC by laminating a thermal insulation layer on the backside of a stamper to retard the heat flow. A macroscopic warpage of PEI substrate is smaller than that of PC substrates, which reduces tilt and servo burden. The lowest critical speed coupled with the flutter of PEI substrate is larger than that of PC substrate because of the mechanical properties of PEI. POLYM. ENG. SCI., 48:97–101, 2008. © 2007 Society of Plastics Engineers     

Local residence time,residence revolution,and residence volume distributions in twin‐screw extruders

This work was aimed at studying the overall, partial, and local residence time distributions (RTD); overall, partial and local residence revolution distributions (RRD) and overall, partial and local residence volume distributions (RVD) in a co‐rotating twin screw extruder, on the one hand; and establishing the relationships among them, on the other hand. Emphasis was placed on the effects of the type and geometry of mixing elements (a gear block and various types of kneading elements differing in staggering angle) and process parameters on the RTD, RRD and RVD. The overall and partial RTD were directly measured in‐line during the extrusion process and the local ones were calculated by deconvolution based on a statistical theory. The local RTD allowed comparing the mixing performance of mixing elements. Also it was confirmed both experimentally and theoretically that specific throughput, defined as a ratio of throughput (Q) over screw speed (N), controlled all the above three types of residence distributions, be they local, partial or overall. The RRD and RVD do not provide more information on an extrusion process than the corresponding RTD. Rather they are different ways of representing the same phenomena. POLYM. ENG. SCI., 48:19–28, 2008. © 2007 Society of Plastics Engineers     

Hydrothermal Reaction Mechanism and Pathway for the Formation of K2Ti6O13 Nanowires

Calculations and detailed first principle and thermodynamic analyses have been performed to understand the formation mechanism of K₂Ti₆O₁₃ nanowires (NWs) by a hydrothermal reaction between bulk Na₂Ti₃O₇ crystals and a KOH solution. It is found that direct ion exchange between K⁺ and Na⁺ plus H⁺ interactions with [TiO₆] octahedra in Na₂Ti₃O₇ promote the formation of an intermediate H₂K₂Ti₆O₁₄ phase. The large lattice mismatch between this intermediate phase and the bulk Na₂Ti₃O₇ structure, and the large energy reduction associated with the formation of this intermediate phase, drive the splitting of the bulk crystal into H₂K₂Ti₆O₁₄ NWs. However, these NWs are not stable because of large [TiO₆] octahedra distortion and are subject to a dehydration process, which results in uniform K₂Ti₆O₁₃ NWs with narrowly distributed diameters of around 10 nm.     

Structural and Superconducting Property Variations with Nominal Mg Non‐Stoichiometry in MgxB2 and Its Enhancement of Upper Critical Field

By applying a combination of characterisation tools, changes in structural and superconducting properties with nominal Mg non‐stoichiometry in Mg_xB₂ are found. The non‐stoichiometry produces enhanced in‐field critical current densities (J_c's) and upper critical field / irreversibility field (H_c2/H_irr(T)) values. Upper critical fields of ～ 21 T (4.2 K) were obtained in nominal Mg‐deficient samples compared to ～ 17 T (4.2 K) for near‐stoichiometric samples.