Multi Response Optimization on Machinability of SiC Waste Fillers Reinforced Polymer Matrix Composite Using Taguchi’s Coupled Grey Relational Analysis

Silicon - Recycling and reutilization of industrial waste is one way to minimize land pollution to attain green environment. In this research waste SiC grinding wheel was ball milled to powder form...     

Performance Analysis of Gate-Stack Dual-Material DG MOSFET Using Work-Function Modulation Technique for Lower Technology Nodes

Silicon - Short channel effects (SCEs) along with mobility degradation has a great impact on CMOS technology below 100 nm. These effects can be overcome by using gate and channel...     

Experimental Investigation on the Performance of a Solar Still Using SiO2 Nanoparticles /Jatropha curcas L

Silicon - Now, enticing systematic civic since everywhere the world is used in green synthesis and benefit of the simple is eco-friendly with an emergent method of producing nanoparticles (NPs)....     

Recent Study on Schottky Tunnel Field Effect Transistor for Biosensing Applications

Silicon - In this review, we discussed highly sensitive biosensor devices which is having a more attractive, wide scope and development in the sensing field. Biosensor devices can detect the...     

Powder Compaction Dies and Compressibility of Various Materials

Powder Metallurgy and Metal Ceramics - Powder compaction is the most crucial process in powder metallurgy since almost all the desired properties of a material, such as a shape, size, density,...     

A new equation of state to predict S-CO<Subscript>2</Subscript> flow with real gas effects

The accuracy of the thermodynamic properties prediction from the different Equation of state (EOS) varies upon the range of temperature and pressure. Despite the variety of EOS available, there is no de facto for selecting an EOS for particular computational modeling. The EOS model recently developed by Kumar and Kim (K-K EOS) determines more accurately the thermodynamic properties of CO₂ than earlier models. In this present study, K-K EOS is successfully implemented in the computational analysis of compressible supercritical CO₂ flow (S-CO₂) in the thermodynamic region near and away from the vapour-liquid critical point. Computational results of SCO₂ flow with the real gas properties predicted with the K-K EOS is compared with Span and Wagner (SW EOS) and ideal EOS.     

Numerical investigation of heat transfer and friction factor in ribbed triangular duct solar air heater using Computational fluid dynamics (CFD)

Journal of Mechanical Science and Technology - The Computational fluid dynamics (CFD) based analysis is carried out to investigate the thermal and hydraulic performance of circular rib roughened...     

Surfactant controlled lubricity of paraffin oil-based nano-emulsion

Oil-in-water emulsions are used as metalworking fluids (MWFs). Considering the environmental issues and operator's health, the amount of oil-in-MWFs is one of the important parameters. In the present study, paraffin oil is used for emulsion formulation and possibilities to minimize the amount of paraffin oil-in-MWFs are explored. Physical characterization of emulsions is done using dynamic light scattering and goniometer. The tribological response of emulsions is recorded using the Four-ball tester. Results indicate that the amount of oil can be brought down to a level of 0.5% v/v to achieve the standard friction level. Droplet size and distribution seems to control the lubricity of emulsions, smaller droplets are desired for better lubrication.     

Dry machining of aluminum for proper selection of cutting tool: tool performance and tool wear

Machining of aluminum and its alloy is very difficult due to the adhesion and diffusion of aluminum, thus the formation of built-up edge (BUE) on the surface. The BUE, which affects the surface integrity and tool life significantly, affects the service and performance of the workpiece. The minimization of BUE was carried out by selection of proper cutting speed, feed, depth of cut, and cutting tool material. This paper presents machining of rolled aluminum at cutting speeds of 336, 426, and 540 m/min, the feeds of 0.045, 0.06, and 0.09 mm/rev, and a constant depth of cut of 0.2 mm in dry condition. Five cutting tools WC SPUN grade, WC SPGN grade, WC + PVD (physical vapor deposition) TiN coating, WC + Ti (C, N) + Al₂O₃ PVD multilayer coatings, and PCD (polycrystalline diamond) were utilized for the experiments. The surface roughness produced, total flank wear, and cut chip thicknesses were measured. The characterization of the tool was carried out by a scanning electron microscope (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD) pattern. The chip underface was analyzed for the study of chip deformation produced after machining. The results indicated that the PCD tool provides better results in terms of roughness, tool wear, and smoother chip underface. It provides promising results in all aspects.