Improved homogenization of Ni in sintered steels through the use of Cr-containing prealloyed powders

The homogenization of Ni in powder metal (PM) steel compacts is usually difficult even after high-temperature sintering at 1250°C. An earlier study by the authors demonstrated that this problem can be alleviated through the addition of 0.5 wt pct Cr in the form of stainless steel powders. To further improve the microstructure and mechanical properties of Ni-containing PM steels and to understand the mechanisms, an attempt was made in this study using the Fe-3Cr-0.5Mo prealloyed powder as the base material. The results showed that the distribution of the Ni additives was significantly improved. As a result, the tensile strength of the Fe-3Cr-0.5Mo-4Ni-0.5C compact sintered at 1250°C reached 1323 MPa. The elongation was higher than 1 pct. These sinter-hardened properties, which were attained using a slow furnace cooling rate, were comparable to those of the sinter-hardened alloys reported in the literature using accelerated cooling and were equivalent to those of the best quenched-and-tempered alloys registered in the Metal Powder Industries Federation (MPIF) standards. These improvements were attributed to the positive effect of Cr addition on alloy homogenization due to the reduction of the repelling effect between Ni and C, as was demonstrated through the thermodynamic analysis using the Thermo-Calc program.     

The effect of grain size, strain rate, and temperature on the mechanical behavior of commercial purity aluminum

Commercial purity aluminum AA1050 was subjected to equal channel angular extrusion (ECAE) that resulted in an ultrafine-grained (UFG) microstructure with an as-received grain size of 0.35 μm. This UFG material was then annealed to obtain microstructures with grain sizes ranging from 0.47 to 20 μm. Specimens were compressed at quasi-static, intermediate, and dynamic strain rates at temperatures of 77 and 298 K. The mechanical properties were found to vary significantly with grain size, strain rate, and temperature. Yield stress was found to increase with decreasing grain size, decreasing temperature, and increasing strain rate. The work hardening rate was seen to increase with increasing grain size, decreasing temperature, and increasing strain rate. The influence of strain rate and temperature is most significant in the smallest grain size specimens. The rate of work hardening is also influenced by strain rate, temperature, and grain size with negative rates of work hardening observed at 298 K and quasi-static strain rates in the smallest grain sizes and increasing rates of work hardening with increasing loading rate and grain size. Work hardening behavior is correlated with the substructural evolution of these specimens.     

Sensor guided handling and assembly of active micro-systems

Positioning accuracies in the range of a few micrometers and below are necessary for the assembly of active micro-systems. In order to reach these accuracies, an assembly system for sensor guided micro-assembly is developed in the Collaborative Research Centre 516 “Design and manufacturing of active micro-systems”. The combination of a parallel robot with an integrated 3D vision sensor and a micro-gripper enables to reach relative positioning accuracies below 1 μm.     

Comprehensive heat exchange model for a semiconductor laser diode

By measuring the total energy flow from an optical device, we can develop new design strategies for thermal stabilization. Here we present a comprehensive model for heat exchange between a semiconductor laser diode and its environment that includes the mechanisms of conduction, convection, and radiation. We perform quantitative measurements of these processes for several devices, deriving parameters such as a laser's heat transfer coefficient, and then demonstrate the feasibility of thermal probing for the nondestructive wafer-scale characterization of optical devices.     

Capture of Organic Vapors Using Adsorption and Electrothermal Regeneration

Activated-carbon-fiber cloth (ACFC) is an alternative adsorbent to granular activated carbon (GAC) for removing and recovering organic vapors from gas streams. Electrothermal desorption (ED) of ACFC provides rapid regeneration while requiring less energy compared to traditional regeneration techniques used with GAC. This paper provides proof-of-concept results from a bench-scale ACFC adsorption system. The automated system captured 1,000 ppmv of hazardous air pollutants/volatile organic compounds (HAPs/VOCs) from air streams and demonstrated the use of ED, using ac voltage, to recover the HAP/VOC as a pure liquid. The desorbed HAP/VOC condensed onto the inner walls of the adsorber and was collected at the bottom of the vessel, without the use of ancillary cooling. Seventy percent of the HAP/VOC was collected per cycle as condensate, with the balance being retained in the regenerated adsorber or recycled to the second adsorber. ED with in-vessel condensation results in minimal N2 consumption and short regeneration cycle times allowing the process to be cost competitive with conventional GAC-based adsorption processes. This technology extends the application of carbon adsorption systems to situations that were previously economically and physically impractical.     

Note on B-splines, wavelet scaling functions, and Gabor frames

Let g be a continuous, compactly supported function on such that the integer translates of g constitute a partition of unity. We show that the Gabor system (g,a,b), with window g and time-shift and frequency-shift parameters a,b>0 has no lower frame bound larger than 0 if b=2,3,... and a>0. In particular, (g,a,b) is not a Gabor frame if g is a continuous, compactly supported wavelet scaling function and if b=2,3,... and a>0. We give an example for our result for the case that g=B/sub 1/, the triangle function supported by [-1,1], by showing pictures of the canonical dual corresponding to (g,a,b) where ab=1/4 and b crosses the lines N=2,3,.     

Understanding silica-supported metal catalysts: Pd/silica as a case study

Supported metal catalysts, particularly noble metals supported on SiO₂, have attracted considerable attention due to the importance of the silica–metal interface in heterogeneous catalysis and in electronic device fabrication. Several important issues, e.g., the stability of the metal–oxide interface at working temperatures and pressures, are not well-understood. In this review, the present status of our understanding of the metal–silica interface is reviewed. Recent results of model studies in our laboratories on Pd/SiO₂/Mo(1 1 2) using LEED, AES and STM are reported. In this work, epitaxial, ultrathin, well-ordered SiO₂ films were grown on a Mo(1 1 2) substrate to circumvent complications that frequently arise from the silica–silicon interface present in silica thin films grown on silicon.     

High-resolution images from low-resolution compressed video

Surveys the field of super resolution (SR) processing for compressed video. The introduction of motion vectors, compression noise, and additional redundancies within the image sequence makes this problem fertile ground for novel processing methods. In conducting this survey, though, we develop and present all techniques within the Bayesian framework. This adds consistency to the presentation and facilitates comparison between the different methods. The article is organized as follows. We define the acquisition system utilized by the surveyed procedures. Then we formulate the HR problem within the Bayesian framework and survey models for the acquisition and compression systems. This requires consideration of both the motion vectors and transform coefficients within the compressed bit stream. We survey models for the original HR image intensities and displacement values. We discuss solutions for the SR problem and provide examples of several approaches.     

Structure and electrical characteristics of Ce4+-doped Ba2In2O5

The In-site of Ba₂In₂O₅ with Brownmillerite structure was partially substituted for Ce⁴⁺ ions in order to examine the doping effect on the order-disorder transition. Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.1, 0.2, 0.3, 0.5, 1.0, and 1.5) were prepared by solid state reaction. X-Ray diffraction analyses of these powder samples demonstrated that Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.1 and 0.2) possesses Brownmillerite structure. With increasing content of Ce⁴⁺ ion the crystal system of Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.3, 0.5, and 1.0) changed to cubic perovskite structure above the order-disorder transition temperature of Ba₂In₂O₅. Arrhenius plots of the electrical conductivities of Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.2, 0.3, and 1.0) exhibited no discontinuity. These compounds had high transference numbers of oxide ion above 973 k.