Upflow anaerobic sludge blanket (UASB) treatment of supernatant of cow manure by thermal pre-treatment.

Upflow anaerobic sludge blanket (UASB) methane fermentation treatment of cow manure that was subjected to screw pressing, thermal treatment and subsequent solid-liquid separation was studied. Conducting batch scale tests at temperatures between 140 and 180 degrees C, the optimal temperature for sludge settling and the color suppression was found to be between 160-170 degrees C. UASB treatment was carried out with a supernatant obtained from the thermal treatment at the optimal conditions (170 degrees C for 30 minutes) and polymer-dosed solid-liquid separation. In the UASB treatment with a COD(Cr) loading of 11.7 kg/m3/d and water temperature of 32.2 degrees C, the COD(Cr) level dropped from 16,360 mg/L in raw water to 3,940 mg/L in treated water (COD(Cr), removal rate of 75.9%), and the methane production rate per COD(Cr) was 0.187 Nm3/kg. Using wastewater thermal-treated at the optimal conditions, also a methane fermentation treatment with a continuously stirred tank reactor (CSTR) was conducted (COD(Cr) in raw water: 38,000 mg/L, hydraulic retention time (HRT): 20 days, 35 degrees C). At the COD(Cr) loading of 1.9 kg/m3/d, the methane production rate per COD(Cr), was 0.153 Nm3/kg. This result shows that UASB treatment using thermal pre-treatment provides a COD(Cr), loading of four times or more and a methane production rate of 1.3 times higher than the CSTR treatment.     

On the problem of hydrogen removal during heat treatment of large forgings

The solutions to a differential equation for the problem of heating of a cylinder in a medium with a fixed temperature are used to obtain equations for estimating the change in the hydrogen concentration in forgings from data on the hydrogen concentration at the cylinder axis or on the average bulk hydrogen concentration. Similar equations are also obtained for forgings having square cross sections. The calculation demonstrates that, for the case of a twofold decrease in the hydrogen concentration in a forging, the calculated times of annealing of a cylindrical forging differ by three times.     

Volumetric out-of-furnace heat treatment of 3600-M3 decomposers

Specifications require that all the welds in 12-m-diam. decomposers with a capacity of 3600 m³ be subjected to high-temperature tempering before going into service in order to alleviate the stresses from the welding operation. Specialists at the organizations VNIIPTkhimnefteapparatury and VNIImontazhspetsstroi have proposed out-of-furnace volumetric (complete) of the assembled decomposer with the use of special heaters. The use of this heating method has shortened assembly operations while providing the welds with a highquality heat treatment and reducing the stresses overall (including welding stresses, stresses from assembly of the decomposer, etc.) The technology ensures uniform heating of the housing of the decomposer and provides for close control over the process. The experience gained in heat-treating decomposers can also be used in the construction of other containers that come into contact with corrosive media. __________ Translated from Metallurg, No. 3, pp. 61–64, March, 2006.     

Ring‐opening polymerization of lactones initiated by diphenylzinc–coinitiator systems

Diphenylzinc, alone or in combination with water and butanone as coinitiators, was used as a polymerization initiator system for a variety of lactones at varying temperatures. The resulting data indicate that the course of the polymerization is greatly influenced by the lactone structure, as well as by the molar ratio of coinitiator to diphenylzinc. When used alone, diphenylzinc exhibited high activity as an initiator in δ‐valerolactone polymerizations, although it was less efficient when used in the β‐butyrolactone and the β‐propiolactone polymerizations. Activity in the polymerization of β‐lactones was increased by adding small amounts of butanone or water. It was also observed that the diphenylzinc–butanone combination was more effective than the diphenylzinc–water mixture in the polymerizations of β‐butyrolactone and β‐propiolactone. Copyright © 2003 Society of Chemical Industry     

Switched-Current Filters Revisited: Square-Root Domain Sampled-Data Filters

In this brief, the well-known switched-current (SI) filtering technique is revisited using the concept of the square-root domain (SRD) filtering. It is proved that SI filters are a subclass of the SRD filters, where sampled-data signal processing is performed. This is achieved by considering typical lossless and lossy SRD sampled-data integrator configurations, using a set of complementary SRD operators which are based on the quadratic I-V relationship of MOS transistor operated in the saturation. Circuit examples are given, where linear-domain integrator and third-order filter configurations were derived using appropriate SRD sampled-data building blocks     

Structural Changes Induced in Nonstoichiometric Titanium Carbide by High-Temperature Deformation

The microstructure evolution in nonstoichiometric titanium carbide is studied during high-temperature deformation at high strain rates and low strains (shock compression) and at slow strain rates and high strains (superplastic regime). The results demonstrate that high-temperature deformation in a broad range of strain rates offers a means of controlling the microstructure of titanium carbide. By varying deformation conditions, one can obtain materials differing in microstructure and chemical composition, in particular, with equilibrium and nonequilibrium microstructures. Accordingly, the physicochemical properties of such materials also differ.     

Motive Force in a Complex Model of Mass Transfer

Relations for determining a motive force in a complex model of mass transfer as applied to concurrent, countercurrent, and cross motion of the vapor and liquid phases have been introduced. These forces have been compared for different forms of organization of the flow, and their comparison with similar quantities from the known Murphree and Hausen models is presented.     

Trajectory control of incompletely restrained parallel-wire-suspended mechanism based on inverse dynamics

This paper discusses parallel wire mechanisms where an end-effector of the mechanism is suspended by multiple wires. The mechanisms enable not only three-dimensional (3-D) positioning but also 3-D orienting of the end-effector, unlike typical wire suspension-type mechanisms such as overhead crane. To discuss the parallel-wire-suspended mechanisms generally, two forms of basic dynamic equations are presented. Then the parallel wire mechanisms are classified into two types based on the basic equations. Dynamical properties of the two types of wire-suspended positioning mechanism are discussed. In this paper, one of the wire-suspended mechanism, incompletely restrained-type parallel wire mechanism, is mainly discussed on its inverse dynamics problem and its trajectory control problem. The inverse dynamics problem for the incompletely restrained-type mechanism plays an important role on its control problem, because the mechanism has low stiffness based on incomplete constraints on the suspended object which is governed by its dynamics. The paper proposes an antisway control method for the suspended object. In the method, the inverse dynamics calculation is used for nonlinear dynamics compensation to control the suspended object of the incompletely restrained parallel wire mechanism.