Preparation,structural and thermo-mechanical properties of lithium aluminum silicate glass–ceramics

Lithium aluminum silicate glasses of composition (wt%) 12.6Li₂O–71.7SiO₂–5.1Al₂O₃–4.9K₂O–3.2B₂O₃–2.5P₂O₅ were prepared by the melt quench technique. These glasses were converted to glass–ceramics based on DTA data. X-ray diffraction (XRD) and Fourier transform infra-red spectroscopy (FTIR) were used to discern the phases evolved in the glass–ceramics. Phase morphology was studied using scanning electron microscopy (SEM). Thermal expansion coefficient (TEC) and glass transition temperature (T_g) of all samples were measured using thermo-mechanical analyzer (TMA). It was found that 3 h dwell time at crystallization temperature yielded samples with good crystallinity with a TEC of 9.461 × 10⁻⁶ °C⁻¹. Glass–ceramic-to-metal compressive seal with SS-304 was fabricated using LAS glass–ceramic. The presence of metal housing and compressive stresses at the glass–ceramic-to-metal interface reduced average grain size and changed the overall microstructure.     

Electrochromic performance of a poly(3,4-ethylenedioxythiophene)-Prussian blue device encompassing a free standing proton electrolyte film

Electrochromic devices incorporating an electropolymerized poly(3,4-ethylenedioxythiophene) (PEDOT) film and a free standing, transparent film of a proton conducting polymer electrolyte with high ambient temperature ionic conductivity of 10⁻² S cm⁻¹ have been fabricated with and without the ion storage electrodeposited Prussian blue (PB) counter electrode layer. While coloration efficiency increases as a function of applied potential in the sole PEDOT device with largest values of CE_(max,VIS) ∼ 120 cm² C⁻¹ and CE_(max,NIR) ∼ 133 cm² C⁻¹ attained at V_c = −1.9 V, the PEDOT:PB device shows a digression from this trend. Much higher coloration efficiencies in the visible (247 cm² C⁻¹ at 570 nm) and NIR (116 cm² C⁻¹ at 1100 nm) regions are achieved for the PEDOT:PB device at a relatively lower reducing voltage of −0.8 V. The PEDOT:PB device shows fast switching redox process (t_c = 2.6 s and t_b = 1.3 s for a 50% optical contrast at 632.8 nm) and a highly reversible charge density as the ratio of Q_inserted to Q_extracted was found to vary between 0.8 and 1.0. When switched between the clear and blue states for 2000 cycles, the insignificant drop in peak current density maxima observed for the PEDOT:PB device, i.e. the good cycling stability, the facile fabrication of device assembly, the ease of scaling up the electrolyte and electrochromic coatings, indicate that this method can be adapted as a simple and inexpensive alternative to conventional electrochromic windows with high cost components.     

The spray forming of nanostructured Aluminum Oxide

Research Summary Nanostructured ceramics and their composites possess improved properties such as tensile strength, fatigue strength, hardness, and wear resistance. Freestanding, near-net shape, nanostructured Al₂O₃ components can be synthesized via plasma-spray forming. In this study, plasma-spray parameters were optimized and an innovative substrate cooling technique was developed to retain nanosize Al₂O₃ in the spray deposit. Nanosize Al₂O₃ particles were partially melted and trapped between the fully melted coarser, micrometersize Al₂O₃grains. Densification of the spray-deposited Al₂O₃occurred via solidification and sintering. A similar processing approach can be adopted for fabrication of near-net shapes of a variety of nanostructured materials (metals, ceramics, and intermetallics) and their combinations by selecting suitable powder-treatment and plasmaspray parameters.     

Synthesis,characterization, and cell viability of bifunctional medical-grade polyurethane nanofiber: Functionalization by bone inducing and bacteria ablating materials

There is an extensive possibility of improving characteristics of fibers used in hard tissue engineering, being hydrophobic and less osteoconductive, resulting in the dynamic growth of new tissues. The current work focuses on the fabrication of nanofibers incorporated with titanium dioxide (TiO₂) ''as osteoconductive'' and silver (Ag) ''as self-healing'' nanoparticles (NPs). The incorporation of AgNO₃ by in situ method not only helped to impart the antibacterial activity but also changed the contact angle from 81 ± 03° in the case of pristine nanofibers to 74 ± 03°, 61 ± 03°, 50 ± 08°, and 39 ± 1.1°, in the composite scaffolds containing 0.01, 0.03, 0.05, and 0.07 M of Ag salts. The incubation in simulated body fluid at 37°C to induce mineralization on nanofiber scaffolds indicated Ca and P crystals' formation. The antibacterial activity showed significantly more toxicity toward E. coli (8.3 ± 0.9 mm) than S. aureus (1.2 ± 0.1 mm). Biocompatibility studies using MTT assay on the pre-osteoblasts showed that both TiO₂ and Ag NPs present in the nanofibers are non-toxic to the bone-like cells. However, results show that a higher concentration of Ag NPs (i.e., 0.07 M) is toxic to cells growing. Finally, all the results suggest that the nanofiber scaffolds have considerable scope for future bone tissue engineering materials.     

Electric field assisted solid-state interfacial joining of TaC-HfC ceramics without filler

The application of ultra-high-temperature ceramics (UHTCs) demands effective ways of joining in overcoming the problems associated with the fabrication of complex-shaped components. In this study, we choose to investigate a new method of rapidly joining pre-sintered TaC and HfC ceramics without any filler material using the spark plasma sintering (SPS) technique. A well-bonded TaC–HfC interface was observed with no apparent cracking and porosity at the joint. The joining mechanisms were predominantly driven by solid-state diffusion and localized plastic deformation. The nanomechanical properties of the TaC-HfC joint are better than the HfC while comparable to that of the TaC. High-load indentation (up to 200 N) results suggest that the TaC–HfC interface is stronger than the parent UHTCs with no crack propagating at the interface. Upon comparison with the parent UHTCs, the damaged area and the average crack length at the interface, reduced up to ~94% and ~56%, respectively. This study shows that the SPS technique can also apply to joining other UHTCs without any filler, resulting in the new field of developing complex components for the thermal protection system (TPS).     

Mesenchymal Stromal Cell Therapy in Novel Porcine Model of Diffuse Liver Damage Induced by Repeated Biliary Obstruction

In liver surgery, biliary obstruction can lead to secondary biliary cirrhosis, a life-threatening disease with liver transplantation as the only curative treatment option. Mesenchymal stromal cells (MSC) have been shown to improve liver function in both acute and chronic liver disease models. This study evaluated the effect of allogenic MSC transplantation in a large animal model of repeated biliary obstruction followed by partial hepatectomy. MSC transplantation supported the growth of regenerated liver tissue after 14 days (MSC group, n = 10: from 1087 ± 108 (0 h) to 1243 ± 92 mL (14 days); control group, n = 11: from 1080 ± 95 (0 h) to 1100 ± 105 mL (14 days), p = 0.016), with a lower volume fraction of hepatocytes in regenerated liver tissue compared to resected liver tissue (59.5 ± 10.2% vs. 70.2 ± 5.6%, p < 0.05). Volume fraction of connective tissue, blood vessels and bile vessels in regenerated liver tissue, serum levels of liver enzymes (AST, ALT, ALP and GGT) and liver metabolites (albumin, bilirubin, urea and creatinine), as well as plasma levels of IL-6, IL-8, TNF-α and TGF-β, were not affected by MSC transplantation. In our novel, large animal (pig) model of repeated biliary obstruction followed by partial hepatectomy, MSC transplantation promoted growth of liver tissue without any effect on liver function. This study underscores the importance of translating results between small and large animal models as well as the careful translation of results from animal model into human medicine.     

Effect of pulsing on reaction outcome in a gas–liquid catalytic packed-bed reactor

A novel experiment is described for studying the effect of flow regime on reaction outcome for a consecutive-parallel reaction. By taking advantage of the convective nature of disturbances that grow into pulses in gas–liquid packed-bed reactors, it is shown that it is possible to compare reaction behavior for pulsing and trickling at the same flow rates. This contrasts previous studies where effects of regime were found, but at different flow rates. This experiment is accomplished by packing the column with mostly inert particles and confining the catalytically active region either near the inlet, where pulses have not yet formed, or near the end where they have developed. It is found that for the reaction of phenylacetylene to styrene and ethylbenzene over a platinum/alumina catalyst, where pulses are present in the bottom of the reactor but not at the top, about a 15% increase in styrene concentration, as an intermediate, occurs under pulsing conditions.     

Residential energy consumption across different population groups: comparative analysis for Latino and non-Latino households in USA

Residential energy cost is an important part of the household budget and could vary significantly across different population groups in many countries. In the United States, many studies have analyzed household fuel consumption by fuel type, including electricity, natural gas, fuel oil, and liquefied petroleum gas (LPG), and by geographic areas. Past research has also demonstrated significant variation in residential energy use across various population groups, including white, black, and Latino. However, our research shows that residential energy demand by fuel type for Latinos, the fastest growing population group, has not been explained by economic and non-economic factors in any statistical model in public domain. The purpose of this paper was to discuss energy demand and expenditure patterns for Latino and non-Latino households in hhe United States as a case example of analyzing residential energy consumption across different population groups in a country. The linear expenditure system model developed by Stone and Geary is the basis of the statistical model developed to explain fuel consumption and expenditures for Latino households. For comparison, the models are also developed for non-Latino, black, and non-black households. These models estimate energy consumption of and expenditures for electricity, natural gas, fuel oil, and LPG by various households at the national level. Significant variations in the patterns of these fuels consumption for Latinos and non-Latinos are highlighted. The model methodology and results of this research should be useful to energy policymakers in government and industry, researches, and academicians who are concerned with economic and energy issues related to various population groups in their country.     

Parametric study of various configurations of hybrid PV/thermal air collector: Experimental validation of theoretical model

In this paper, an attempt has been made to evaluate the overall performance of hybrid PV/thermal (PV/T) air collector. The different configurations of hybrid air collectors which are considered as unglazed and glazed PV/T air heaters, with and without tedlar. Analytical expressions for the temperatures of solar cells, back surface of the module, outlet air and the rate of extraction of useful thermal energy from hybrid PV/T air collectors have been derived. Further an analytical expression similar to Hottel–Whiller–Bliss (HWB) equation for flat plate collector has also been derived in terms of design and climatic parameters. Numerical computations have been carried out for composite climate of New Delhi and the results for different configurations have been compared. The thermal model for unglazed PV/T air heating system has also been validated experimentally for summer climatic conditions. It is observed that glazed hybrid PV/T without tedlar gives the best performance.