The effect of microencapsulation with nitrocellulose on thermal properties of sodium azide particles

Based on the coacervation principle a solvent/non-solvent method has been used for microencapsulation of sodium azide (NaN₃) with fibrous nitrocellulose (NC). Scanning electron microscopy (SEM) was employed to examine the coating morphology. The thermal behavior of solid samples has been studied by means of thermogravimetry (TG) and differential scanning calorimetry (DSC). The results of TG–DTA analysis revealed that the main thermal degradation for the pure NC and NaN₃ occurs in the temperature ranges of 192–220 and 415–420 °C, respectively. The effects of some parameters, such as NC to NaN₃ weight ratio and volume and addition time of non-solvent, on coating quality and thermal properties have been investigated by SEM and thermal methods. The results of these experiments showed that the decomposition temperature of most stabilized coated sodium azide is about 50 °C higher than that of the pure sample. The DSC experiments were conducted to study the influence of the heating rate (5, 10, 15 and 20 °C/min) on the thermal decomposition processes of the pure NC, coated and pure NaN₃ samples. The results revealed that, as the heating rate was increased, decomposition temperature of the compounds was increased. Also, the kinetic parameters such as activation energy and frequency factor of the decomposition processes were obtained from the DSC data by non-isothermal methods proposed by ASTM E696 and Ozawa. Our finding showed that coated NaN₃ has lower decomposition rate with respect to the pure one.     

Improvement in volume resistivity and morphology of a blend of polyolefin elastomer with linear low-density polyethylene

A silane moisture-cured polyolefin elastomer/linear low-density polyethylene (LLDPE) blend was prepared through a two-step silane-grafting method (Sioplas Process) in an industrial scale twin-screw extruder. The silane-grafted compound was used to make wire and cable coatings. In this work, the effect of some interactive parameters on quality of the products prepared by the above method has been studied, while so far, there have been less experimental investigations. The volume resistivity of cross-linked compound was changed from 2.96 × 10¹⁴ to 7.41 × 10¹⁴ Ω cm with increasing LLDPE component by maximum 10 wt%. Surface morphology of the product was corrected with reduction in benzoyl peroxide (BPO) concentration from 0.2 wt% to 0.13 wt%. BPO at this level acted as an initiator in grafting reaction of vinyl trimethoxysilane. The curing condition and specimen preparation method by injection molding and/or extrusion were factors which influenced the hot-set test results at 200 °C. The results of tensile and elongation studies showed a maximum value of 9 MPa and 397% for the tests, after 6 h curing. With increases in curing time at a specified temperature, the gel content of the cross-linked compound was increased and reached its maximum value. The maximum gel content values were found to be approximately 60%, 80%, and 82% at temperatures of 25, 60, and 85 °C, respectively. The hardness, density, and tear strength of the samples did not vary significantly with the curing temperature.

     

Synthesis of colloidal nanosilica from waste glass powder as a low cost precursor

Waste glass powder was used as a low cost precursor for production of colloidal nanosilica for the first time. The process includes production of wet silica gel and thermal peptization of the wet gel. Purification of the glass powder and wet gel production were initiated by acid washing. The obtained powder was reacted with sodium hydroxide to produce wet silica gel. Type of the applied acid was examined in one factor at a time route. Temperature of the alkaline step and concentrations of the applied acid and base were investigated using Taguchi design of experiments. After finding the best combination of the investigated factor levels in production of the wet gel, time of the stabilization in thermal peptization was studied. Characterizations of the wet gel and colloidal silica were performed by XRF, DLS, FESEM, TEM, FTIR and N₂ sorption evaluation. Accordingly pure and stable colloidal nanosilica (98.50%) with average particle size of 21.9?nm was produced from the glass powder successfully. Specific surface area of the dried porous optimum sample was 83.63?m²/g.     

CO2/CH4 Separation by Adsorption using Nanoporous Metal organic Framework Copper‐Benzene‐1,3,5‐tricarboxylate Tablet

Equilibrium data for carbon dioxide and methane adsorption on nanoporous metal organic framework Cu‐BTC powder and tablets were measured in a magnetic suspension balance in the temperature range of 308–373 K and a pressure range of 0–7 bar and fitted with Langmuir model. The tablets adsorption loading is 0.63 mol kg^–1 for methane and 3.1 mol kg^–1 for carbon dioxide at 1 bar and 308 K, while these values are 0.77 and 3.9 mol kg^–1 for powder in the same conditions. Isosteric heats of adsorption were 22.8 and 15.0 kJ mol^–1 for carbon dioxide and methane, respectively, on both adsorbents, which indicates a strong adsorption of carbon dioxide. Also, single and binary breakthrough curves were measured in the same temperature range and atmospheric pressure by using Cu‐BTC tablets as adsorbent. A complete model was used in the simulation of breakthrough curves and good agreement was observed with experimental data.     

A STUDY OF NON-NEWTONIAN FLOW AND HEAT TRANSFER OVER A NON-ISOTHERMAL WEDGE USING THE HOMOTOPY ANALYSIS METHOD

The thermoconvective boundary layer flow of a generalized third-grade viscoelastic power-law non-Newtonian fluid over a porous wedge is studied theoretically. The free stream velocity, the surface temperature variations, and the injection velocity at the surface are assumed variables. A similarity transformation is applied to reduce the governing partial differential equations for mass, momentum, and energy conservation to dimensionless, nonlinear, coupled, ordinary differential equations. The homotopy analysis method (HAM) is employed to generate approximate analytical solutions for the transformed nonlinear equations under the prescribed boundary conditions. The HAM solutions, in comparison with numerical solutions (fourth-order Runge-Kutta shooting quadrature), admit excellent accuracy. The residual errors for dimensionless velocity and dimensionless temperature are also computed. The influence of the “power-law” index on flow characteristics is also studied. The mathematical model finds important applications in polymeric processing and biotechnological manufacture. HAM holds significant promise as an analytical tool for chemical engineering fluid dynamics researchers, providing a robust benchmark for conventional numerical methods.     

Application of mesoporous magnetic carbon composite for reactive dyes removal: Process optimization using response surface methodology

Discharging the effluents of textile wastewaters into potable water resources can endanger the ecosystem, due to their reactivity, toxicity, and chemical stability. In this research, the application of powder activated carbon modified with magnetite nanoparticles (PAC-MNPs) as an adsorbent for removal of reactive dyes (Reactive black 5 (RB5) and reactive red 120 (RR120)) was studied in a batch system. The adsorption performance was evaluated as a function of temperature, contact time and different adsorbent and adsorbate concentrations. The levels of factors were statistically optimized using Box-Behnken Design (BBD) from the response surface methodology (RSM) to maximize the efficiency of the system. The adsorption process of both dyes was fit with the pseudo-second order kinetic and Langmuir isotherm models. The identified optimum conditions of adsorption were 38.7 °C, 46.3 min, 0.8 g/L and 102 mg/L for temperature, contact time, adsorbent dose, and initial dyes concentration, respectively. According to the Langmuir isotherm, the maximum sorption capacities of 175.4 and 172.4 mg/g were obtained for RB5 and RR120, respectively. Thermodynamics studies indicated that the adsorption process of the reactive dyes was spontaneous, feasible, and endothermic. After five cycles, the adsorption efficiency was around 84 and 83% for RB5 and RR120, respectively. A high value of desorption was achieved, suggesting that the PAC-MNPs have a good potential in regeneration and reusability, and also can be effectively utilized in industrial applications. PAC-MNPs also show a good anti-interference potential for removal of reactive dyes in dye-industry wastewaters.     

A modern congestion pricing policy for urban traffic: subsidy plus toll

Railway Engineering Science - Congestion pricing is seen as an effective policy to address traffic congestion. In such policies where money, people and authorities are involved, the success...