Results of testing a centrifugal bubble singlet-oxygen generator

The results of parametric tests of a centrifugal bubble singlet-oxygen generator based on the reaction of chlorine with an alkaline hydrogen peroxide solution have been given. The utilization of chlorine grows with bubble-layer height, whereas the relative content of O₂(¹Δ) remains constant. Growth in centrifugal acceleration leads to a more efficient utilization of chlorine. A specific oxygen output of more than 1 mmole·cm⁻²·sec⁻¹ from the bubble layer for a degree of chlorine utilization of ∼95% and a singlet-oxygen yield of more than 50% has been attained. It has been shown that a centrifugal bubble singlet-oxygen generator is an efficient energy source for an oxygen-iodine laser. __________ Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 80, No. 3, pp. 121–128, May–June, 2007.     

Fast numerically stable computation of orthogonal Fourier?Mellin moments

An efficient algorithm for the computation of the orthogonal Fourier-Mellin moments (OFMMs) is presented. The proposed method computes the fractional parts of the orthogonal polynomials, which consist of fractional terms, recursively, by eliminating the number of factorial calculations. The recursive computation of the fractional terms makes the overall computation of the OFMMs a very fast procedure in comparison with the conventional direct method. Actually, the computational complexity of the proposed method is linear O(p) in multiplications, with p being the moment order, while the corresponding complexity of the direct method is O(p²). Moreover, this recursive algorithm has better numerical behaviour, as it arrives at an overflow situation much later than the original one and does not introduce any finite precision errors. These are the two major advantages of the algorithm introduced in the current work, establishing the computation of the OFMMs to a very high order as a quite easy and achievable task. Appropriate simulations on images of different sizes justify the superiority of the proposed algorithm over the conventional algorithm currently used     

Low loss guided wave propagation in a left-handed microstrip structure using dispersive split ring?rod combination metamaterial

Split ring-rod combination metamaterial is used as a substrate material in a microstrip guided wave structure to determine what the effect is of a material with potentially excessive dispersion or loss or both. A Green's function method readily incorporates the metamaterial permittivity and permeability tensor characteristics. Ab initio calculations are performed to obtain the dispersion diagrams of several complex propagation constant modes of the structure. Analytical analysis is done for the design and interpretation of the results, which demonstrate remarkable potential for realistic use in high frequency electronics, while showing modes with extremely low loss bands.     

Development of Free-Electron x-Ray Lasers on the TESLA Test Accelerator (DESY, Germany)

The program for developing free-electron x-ray lasers at TESLA started in 1994. The plan is to use the TESLA test accelerator to develop an x-ray laser with minimum wavelength 0.1–6 nm. The first phase of the project was successfully completed in 2001. At saturation, the laser produces ultrashort 30–100 fsec, gigawatt, radiation pulses. The wavelength can be tuned smoothly over the range 80–120 nm.     

Inference of message sequence charts

Software designers draw message sequence charts for early modeling of the individual behaviors they expect from the concurrent system under design. Can they be sure that precisely the behaviors they have described are realizable by some implementation of the components of the concurrent system? If so, can we automatically synthesize concurrent state machines realizing the given MSCs? If, on the other hand, other unspecified and possibly unwanted scenarios are "implied" by their MSCs, can the software designer be automatically warned and provided the implied MSCs? In this paper, we provide a framework in which all these questions are answered positively. We first describe the formal framework within which one can derive implied MSCs and then provide polynomial-time algorithms for implication, realizability, and synthesis.     

Itemset trees for targeted association querying

Association mining techniques search for groups of frequently co-occurring items in a market-basket type of data and turn these groups into business-oriented rules. Previous research has focused predominantly on how to obtain exhaustive lists of such associations. However, users often prefer a quick response to targeted queries. For instance, they may want to learn about the buying habits of customers that frequently purchase cereals and fruits. To expedite the processing of such queries, we propose an approach that converts the market-basket database into an itemset tree. Experiments indicate that the targeted queries are answered in a time that is roughly linear in the number of market baskets, N. Also, the construction of the itemset tree has O(N) space and time requirements. Some useful theoretical properties are proven.     

Fatigue Behavior and Retrofit Investigation of Distortion-Induced Web Gap Cracking

This paper studies a Kansas Department of Transportation welded plate girder bridge that developed fatigue cracks at small web gaps close to the girder top flange. Repair had been previously performed by softening the connection plate end with a slot retrofit, but cracks were recently found to have reinitiated at some of the repaired details and are again propagating. A comprehensive finite-element method study was performed to investigate the cracking behavior observed in the bridge and to recommend appropriate measures for future bridge retrofit. The analytical results show that stresses developed at the top flange web gaps could exceed yielding under the loading of an HS15 fatigue truck. The current slot repair used in the bridge was found to have introduced higher magnitude fatigue stresses in the web gap. To achieve a permanent repair of the bridge, it is recommended that a welded connection plate to flange attachment be used during future bridge retrofit. The web gap details should be able to withstand unlimited number of load cycles once this additional repair is performed.     

Characterization of strength properties of thin polycrystalline silicon films for MEMS applications

The aim of this work is to characterize the strength properties of polycrystalline silicon (polysilicon) with the use of tensile and bending test specimens. The strength of thin polysilicon films with different geometry, size and stress concentrations has been measured and correlated with the effective size of the specimen and its stress distribution. The test results are evaluated using a probabilistic strength approach based on the weakest link theory with the use of STAU software. The use of statistic methods of strength prediction of polysilicon test structures with a complex geometry and loading based on test values for standard material tests specimen has been evaluated.     

Low-cycle fatigue in silicon: comparison with fcc metals

Undoped FZ silicon single crystals were cyclically loaded in tension‐compression under plastic strain amplitude control in a temperature and strain rate domain where the glide of dislocations is still controlled by the lattice friction: 1073–1173 K and (1.5–6) × 10⁻⁴s⁻¹; the plastic strain amplitude being varied from 6 × 10⁻⁴ to 10⁻². Cyclic hardening curves display logarithmic then linear hardening and pass through a maximum before the peak stress per cycle stabilizes. The maximum and stabilized stresses decrease when temperature increases. Microscopical observations suggest that strain localization takes place near the maximum cyclic stress and beyond. But, contrary to what is observed in fcc metals, the maximum or saturation stress decreases when the strain amplitude per cycle increases. Several types of dislocation arrangements, rather different from those found in copper, but looking more similar to Ni fatigued at low temperatures, were revealed by transmission electron microscopy. Before mechanical saturation, edge dislocation dipoles gather in thick stripes forming more or less corrugated walls, depending on the amplitude per cycle, when viewed normal to the primary slip plane. Once the maximum stress is reached, it seems that parts of the microstructure cease to participate in the imposed plastic strain, while others concentrate it. In active areas, thick walls condense into much thinner ones, forming chevrons when viewed normal to the slip plane. In areas which seem to be inactive, dipolar walls anneal out leaving a rather homogeneous distribution of prismatic loops. Thin PSBs with a well‐characterized ‘ladder‐structure’ are very rare. Characteristic lengths of the observed patterns are given and briefly discussed using current theories of cyclic deformation.     

A direct estimate of JIc from the load versus load-line displacement record

The purpose of this study is to examine the current standard fracture toughness test procedure to determine if there could be an easier method to get a J_Ic value from the test record. The current method for determining J_Ic involves a detailed computational and construction procedure. The objective in this study is to simplify the analysis for the determination of J_Ic. The results of this study show that the load and displacement record for a fracture toughness test can be used to directly estimate a J_Q value, a provisional value for fracture toughness, J_Ic. The J value taken at the maximum load point can be used along with an adjustment factor to estimate a J_Q value. This J_Q estimate is close to the one obtained from the construction procedure of ASTM Standard E 1820. When a unit‐sized specimen is tested, that is, a specimen with a width of 50 mm and a thickness of 25 mm the maximum load point provides a direct estimate of J_Q. Other sizes require a size adjustment factor, which is simply a square root relationship between the width of the test specimen and a unit width. The proposed new method of estimating J_Q is simple in concept and requires a minimum number of calculations. It appears to produce values of J_Q which are comparable to those obtained from the ASTM E1820 construction procedure and may produce less scatter.