秦山核电厂燃耗深度对DNBR限值的影响分析

本文研究了在秦山核电厂批平均卸料燃耗深度超过原定限值的情况下，为保证电厂的安全运行对DNBR限值进行重新确认的问题。研究过程中，综合考虑了由燃耗加深所引起的核焓升因子的变化和棒弯曲这两种效应对DNBR限值的影响。结果表明，对秦山核电厂而言，在批平均卸料燃耗超过原定限值的情况下，维持原DNBR限值不变仍是安全可行的。     

尿素解吸废液及甲醇残液联合处理工艺的应用

安阳化学工业集团公司(以下简称安化集团)现有2套200 kt/a尿素装置及1套60 kt/a甲醇装置.尿素及甲醇装置在生产过程中会产生大量的尿素解吸废液和甲醇残液,废液中的氨氮(NH3-N)含量和化学需氧量(CODCr)较高,给该公司废水的达标排放带来很大压力.     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

驱蚊酯的合成及应用研究

本文合成了一种高效低毒驱蚊剂-驱蚊酯[(insectifuge ester)[1],3-(Acetyl-butyl-amino)-propionic acid ethyl ester],并对其结构进行了全面鉴定,同时对其合成过程中所产生的副产物进行了分析测定。用驱蚊酯配成含2.3%驱蚊酯的花露水,并测试了其驱蚊效果,有效驱蚊时间可达5小时以上。     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.     

Poly(butylene terephthalate)–clay nanocomposites prepared by melt intercalation: morphology and thermomechanical properties

Nanocomposites based on poly(butylene terephthalate) (PBT) and an organoclay (Cloisite 30B) were prepared by melt blending using a twin‐screw extruder. Two kinds of PBTs, ie PBT‐A and PBT‐B, with different inherent viscosities (η_inh), were used for this study (η_inh of PBT‐A and PBT‐B were 0.74 and 1.48, respectively). Dispersion of the clay layers in the PBT nanocomposites was characterized by using X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Tensile and dynamic mechanical properties and non‐isothermal crystallization temperatures of the nanocomposites were also examined. Nanocomposites based on the higher‐viscosity PBT (PBT‐B) showed a higher degree of exfoliation of the clay and a higher reinforcing effect when compared to the composites based on the lower‐viscosity PBT (PBT‐A). The clay nanolayers dispersed in PBT matrices lead to increases in the non‐isothermal crystallization temperatures of the PBTs, with such increases being more significant for the PBT‐B nanocomposites than for the PBT‐A nanoocomposites. Copyright © 2004 Society of Chemical Industry     

Facile modifications of polyimide via chloromethylation: II. Synthesis and characterization of thermocurable transparent polyimide having methylene acrylate side groups

From chloromethylated polyimide, a useful starting material for modification of aromatic polyimides, a thermocurable transparent polyimide having acrylate side groups was prepared. In the presence of 1,8‐diazabicyclo[5,4,0]undec‐7‐ene, chloromethylated polyimide was esterified with acrylic acid to synthesize poly(imide methylene acrylate). The polymer was soluble in organic solvent, which makes it possible to prepare a planar film by spin coating. The polymer film became insoluble after thermal treatment at 230 °C for 30 min. Optical transparency of the film at 400 nm (for 1 µm thickness) was higher than 98 % and not affected by further heating at 230 °C for 250 min. Adhesion properties measured by the ASTM D3359‐B method ranged from 4B to 5B. Preliminary results of planarization testing showed a high degree of planarization (DOP) value (>0.53). These properties demonstrate that poly(imide methylene acrylate) could be utilized as a thermocurable transparent material in fabricating display devices such as TFT‐LCD. Copyright © 2004 Society of Chemical Industry     

Properties of poly(ethylene terephthalate)–poly(ethylene naphthalene 2,6‐dicarboxylate) blends with montmorillonite clay

The production and properties of blends of poly(ethylene terephthalate) (PET) and poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) with three modified clays are reported. Octadecylammonium chloride and maleic anhydride (MAH) are used to modify the surface of the montmorillonite–Na⁺ clay particles (clay–Na⁺) to produce clay–C18 and clay–MAH, respectively, before they are mixed with the PET/PEN system. The transesterification degree, hydrophobicity and the effect of the clays on the mechanical, rheological and thermal properties are analysed. The PET–PEN/clay–C18 system does not show any improvements in the mechanical properties, which is attributed to poor exfoliation. On the other hand, in the PET–PEN/clay–MAH blends, the modified clay restricts crystallization of the matrix, as evidenced in the low value of the crystallization enthalpy. The process‐induced PET–PEN transesterification reaction is affected by the clay particles. Clay–C18 induces the largest proportion of naphthalate–ethylene–terephthalate (NET) blocks, as opposed to clay–Na⁺ which renders the lowest proportion. The clay readily incorporates in the bulk polymer, but receding contact‐angle measurements reveal a small influence of the particles on the surface properties of the sample. The clay–Na⁺ blend shows a predominant solid‐like behaviour, as evidenced by the magnitude of the storage modulus in the low‐frequency range, which reflects a high entanglement density and a substantial degree of polymer–particle interactions. Copyright © 2005 Society of Chemical Industry     

Morphology and properties of poly[2‐methoxy‐5‐(2′‐ethyl‐hexyloxy)‐para‐phenylene vinylene]/silica nanoparticle hybrid films

Poly[2‐methoxy‐5‐(2′‐ethyl‐hexyloxy)‐para‐phenylene vinylene] (MEH‐PPV)/silica nanoparticle hybrid films were prepared and characterised. Three kinds of materials were compared: parent MEH‐PPV, MEH‐PPV/silica (hybrid A films), and MEH‐PPV/coupling agent MSMA/silica (hybrid B films), in which MSMA is 3‐(trimethoxysilyl) propyl methacrylate. It was found that the hybrid B films could significantly prevent macrophase separation, as evidenced by scanning electron and fluorescence microscopy. Furthermore, the thermal characteristics of the hybrid films were largely improved in comparison with the parent MEH‐PPV. The UV‐visible absorption spectra suggested that the incorporation of MSMA‐modified silica into MEH‐PPV could confine the polymer chain between nanoparticles and thus increase the conjugation length. The photoluminescence (PL) studies also indicated enhancement of the PL intensity and quantum efficiency by incorporating just 2 wt% of MSMA‐modified silica into MEH‐PPV. However, hybrid A films did not show such enhancement of optoelectronic properties as the hybrid B films. The present study suggests the importance of the interface between the luminescent organic polymers and the inorganic silica on morphology and optoelectronic properties. Copyright © 2004 Society of Chemical Industry