Studies on the semirigid chain polyamide—poly(1,4-phenyleneterephthalamide)

In this article, the polycondensation of terephthaloyl chloride and p-phenylenediamine was systematically studied, including the liquid–crystalline state of the solution and the spinning of poly(1,4-phenyleneterephthalamide) (PPTA). High-molecular-weight PPTA with ε_inh = 5–7 was prepared and the main factors influencing the solution polycondensation of 1,4-phenylenediamine with terephthaloyl chloride were studied in detail. Experimental results showed that the water content of the reaction system, reactant concentration, and volume ratio of mix solvents have a great influence on the inherent viscosity of the poly(1,4-phenyleneterephthalamide) obtained. The highest ε_inh was obtained at 0.3M/liter reactant concentration in a mixed solvent ratio HMPA/DMAC of 4/1 (by volume), at 0.35M/liter reactant concentration in a mixed solvent of HMPA/NMP = 7/3, and at 0.5M/liter of reactant concentration in a mixed solvent of HMPA/THF = 9/1. The water content must be controlled to less than 100 ppm in the polymerization system. In the early stage of the polycondensation process, the ε_inh of the polymer obtained increased rapidly with time. The system gelled within 2 or 3 min, while the monomer conversion reached about 100%. However, the reaction of polycondensation continued after gelation and the ε_inh of the polymer increased appreciably. We have studied the viscosity behavior at 20–155°C for the anisotropic solution of PPTA in 100% sulfuric acid (ε_inh of PPTA 2.5–4.9). Experimental results showed that, at low concentrations the viscosity of isotropic solution increases with the increase of polymer concentration to reach a maxium near the critical polymer concentration, beyond which the solution changes to an anisotropic liquid–crystalline solution. The appropriate spinning region was obtained as shown in the phase diagram determined by viscosity, degree of depolarization anisotropy, and region of thermal depolymerization. Fibers of PPTA with high modulus and high tenacity were obtained by dry-jet wet spinning. The fibers obtained have a tenacity of ～22 g/denier, a modulus of ～600 g/denier, and elongation at break ～3.5%.     

粉体高浓度输送相图

根据以固体质量流速和固体装入量为参数的Zenz相图（即压降与表观气速的关系图）和洪江等人的模型[6]，对粗聚氯乙烯和细PVC颗粒的水平气力输送进行了合理的预测     

Synthesis and characterization of new aromatic polyimides containing well‐defined conjugation units

A series of aromatic polyimides composed of well‐defined conjugation units were synthesized form 5,5′‐bis(4‐aminophenyl)‐2,2′‐bifuryl (PFDA) and 2,2′‐bis(furyl) benzidine (FurylBZ) with various dianhydrides. The synthesized polyimides emit blue to green light with a quantum yield of 7.3–14.9%, depending on the polymer backbone. In particular, PFDA‐based polymers exhibit extremely narrow photo‐luminescence. The structure, thermal stability, refractive index and dielectric properties of the polymer films were also determined.     

反应型共聚物相容剂在聚合物合金中的应用

反应型共聚物相容剂所含的反应官能团与共混物中聚合物的相关的官能团发生化学反应，从而改善不相容聚合物共混物的相容性。本文介绍了反应型共聚物相容剂的分子设计，合成及其应用。     

Synthesis and properties of fluorinated aromatic poly(amide imide)s based on 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzophenone and various bis(trimellitimide)s

A CF₃‐containing diamine, 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzophenone ( 2 ), was synthesized from 4,4′‐dihydroxybenzophenone and 2‐chloro‐5‐nitrobenzotrifluoride. Imide‐containing diacids ( 3 and 5B_a – 5B_g ) were prepared by the condensation reaction of aromatic diamines and trimellitic anhydride. Then, two series of novel soluble aromatic poly(amide imide)s (PAIs; 6A_a – 6A_k and 6B_a – 6B_g ) were synthesized from a diamine ( 4A_a – 4A_k or 2 ) with the imide‐containing diacids ( 3 and 5B_a – 5B_g ) via direct polycondensation with triphenyl phosphate and pyridine. The aromatic PAIs had inherent viscosities of 0.74–1.76 dL/g. All of the synthesized polymers showed excellent solubility in amide‐type solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide (DMAc), and afforded transparent and tough films by DMAc solvent casting. These polymer films had tensile strengths of 90–113 MPa, elongations at break of 8–15%, and initial moduli of 2.0–2.9 GPa. The glass‐transition temperatures of the aromatic PAIs were in the range 242–279°C. They had 10% weight losses at temperatures above 500°C and showed excellent thermal stabilities. The 6B series exhibited less coloring and showed lower yellowness index values than the corresponding 6A series. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:3641–3653, 2006     

The preparation of coupled WO3/TiO2 photocatalyst by ball milling

The coupled photocatalyst WO₃/TiO₂ is prepared by ball milling by doping WO₃ into TiO₂ and using H₂O solution as disperser. The coupled photocatalyst WO₃/TiO₂ is characterized by UV–VIS diffuse reflection spectrum, X-ray photoelectron spectroscopy (XPS), X-ray powder diffraction (XRD) and Transmission electron microscopy (TEM). The results show that the optimum percentage of WO₃ doped is 3% and that the photocatalytic activity of the coupled WO₃/TiO₂ photocatalyst is much higher than that of TiO₂ and WO₃–TiO₂ with no ball milling. Compared with TiO₂, the photoexcited wavelength range of the WO₃/TiO₂ photocatalyst red-shifts about 50 nm, and the light absorption intensity is also improved. The crystal phase of TiO₂ is not changed and new crystal phases are not found during the process of ball milling. WO₃ and TiO₂ coupled highly, forming the WO₃/TiO₂ photocatalyst. The increased photocatalytic activity of the coupled photocatalyst may be attributed to the enhance charge separation efficiency and the extend wavelength range of photoexcitation.     

Study on the polymerization of ϵ‐caprolactam in the interlamellar spaces of [TEACOOH]–montmorillonite intercalations complex and its characterization

The polymerization of ?‐caprolactam between the interlamellar spaces of the [TEACOOH]–montmorillonite intercalations complex was attempted using Na–montmorillonite and 10‐carboxy‐n‐decyltriethylammonium bromide to achieve [TEACOOH]–polycaprolactam–montmorillonite, in which montmorillonite (inorganic polymer) is chemically bonded with the polycaprolactam (organic polymer). The results of X‐ray and IR analysis for the samples obtained after polymerization showed that the polymerization reaction has been successfully accomplished. For the purpose of studying the polymeric reaction product more precisely, we have isolated the polymerized product from the silicate layers and analyzed it with X‐ray diffractometer and IR spectrometer. Comparison of the results of X‐ray and IR analysis between the isolated polymer and the polymer that was synthesized by the reaction of ?‐caprolactam only with the organic cation without montmorillonite showed that both obtained polymers are the same compounds. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1904–1910, 2003     

Thermal and thermomechanical properties of poly(ethylene oxide) networks produced with silica and organic crosslinking agents

The thermal and thermomechanical properties of two series of poly(ethylene oxide) networks (NPEOs) were investigated as a function of the chain length between crosslink sites (M_c) and the concentration of LiClO₄ (C_L) in the NPEOs. The two series of networks were produced with silica and organic crosslinking agents and, therefore, had crosslink sites of different natures: one was an inorganic silicate network (silica NPEO), and the other was an organic polar group (organic NPEO). The crosslink sites in both series of networks were commonly covalently bonded to the poly(ethylene oxide) (PEO) phase through a urethane group in the NPEOs. The glass‐transition temperatures (T_g's) of the PEO phases in the NPEOs, according to differential scanning calorimetry, increased with a decrease in M_c and were higher in the silica NPEOs than in the organic NPEOs under the same M_c conditions. The difference in T_g between the two series of networks with the same M_c values increased with decreasing M_c. These results suggested that the interaction of crosslink sites with the PEO phase was stronger in the silica NPEOs than in the organic NPEOs. The addition of LiClO₄ to the NPEOs resulted in T_g of the PEO phase in the NPEOs being elevated and increased according to the increase in C_L. The increase of T_g of the PEO phase according to the increase of C_L in the NPEOs was retarded or saturated at high values of C_L, and this indicated that the limit of solubility of the salt in the polymer was attained. The retardation or saturation of the increase of T_g was also observed in dynamic mechanical analyses. The curves of the loss factor tan δ and temperatures from the dynamic mechanical analyses for the NPEOs with high values of C_L showed shoulders or double peaks indicating the existence of the second phase in the polymer networks. In the curves of tan δ for salt‐complexed NPEOs with high values of C_L, silica NPEOs showed a shoulder of low intensity, but organic NPEOs showed a distinguished second peak becoming stronger with increasing C_L. The results of the T_g behavior and tan δ curves suggested that the salt solubility in the NPEOs was limited and that the salt solubility of PEO in the silica NPEOs was higher than that in the organic NPEOs. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 270–277, 2003     

Low‐temperature photoinitiation solution polymerization behavior of N‐vinylcarbazole in tetrahydrofuran

N‐Vinylcarbazole (VCZ) was solution‐polymerized in tetrahydrofuran (THF) at ?20, 0, and 20°C using the photoinitiation method; the effects of the amount of solvent, polymerization temperature, and photoinitiator concentration were investigated. On the whole, the experimental results corresponded to predicted ones. Low polymerization temperature using photoinitiation proved to be successful in obtaining poly(N‐vinylcarbazole) (PVCZ) of a high molecular weight with a smaller temperature rise during polymerization; nevertheless of free radical polymerization by 2,2′‐azobis(2,4‐dimethylvaleronitrile) (ADMVN). The photo‐solution polymerization rate of VCZ in THF was proportional to the 0.47 power of ADMVN concentration. The molecular weight was higher and the molecular weight distribution was narrower with PVCZ polymerized at lower temperatures. For PVCZ prepared in THF at ?20°C using a photoinitiator concentration of 0.00005 mol/mol of VCZ, a weight‐average molecular weight of 510,000 was obtained, with a polydispersity index of 1.73, and a degree of lightness converged to about 99%. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3667–3672, 2002     

Properties and crystallization kinetics of poly(ether ether ketone)‐co‐poly(ether ether ketone ketone) block copolymers

A series of block copolymers composed of poly(ether ether ketone) (PEEK) and poly(ether ether ketone ketone) (PEEKK) components were prepared from their corresponding oligomers via a nucleophlilic aromatic substitution reaction. Various properties of the copolymers were investigated with differential scanning calorimetry (DSC) and a tensile testing machine. The results show that the copolymers exhibited no phase separation and that the relationship between the glass‐transition temperature (T_g) and the compositions of the copolymers approximately followed the formula T_g = T_g1X₁ + T_g2X₂, where T_g1 and T_g2 are the glass‐transition‐temperature values of PEEK and PEEKK, respectively, and X₁ and X₂ are the corresponding molar fractions of the PEEK and PEEKK segments in the copolymers, respectively. These copolymers showed good tensile properties. The crystallization kinetics of the copolymers were studied. The Avrami equation was used to describe the isothermal crystallization process. The nonisothermal crystallization was described by modified Avrami analysis by Jeziorny and by a combination of the Avrami and Ozawa equations. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1652–1658, 2005