富氧燃烧技术在石灰回转窑中的应用研究及经济性预测

利用燃烧学理论及其相关知识对富氧燃烧技术的特点进行了详细的理论分析.在此基础上针对某公司拟在石灰回转窑中应用该技术的工程案例进行了计算,提出了3种不同的技改方案,并对其经济性进行了预测.结果表明在不改变现有燃烧设备的条件下,采用焦炉煤气和转炉煤气混合富氧的方案,氧体积分数控制在21.4%时最为合理;采用焦炉煤气和高炉煤气混合富氧的方案,氧体积分数控制在23.0%时最为合理;从成本分析前者更具有竞争性.如果对现有燃烧设备进行改造,建议采用转炉煤气和高炉煤气混合富氧的方案,氧体积分数控制为28.0%时,成本节约潜力最大,对该公司最有实用意义,此时对应的煤气流量约为20 km3/h.     

The effect of cooling rate on the impact performance and dynamic mechanical properties of rotationally molded metallocene catalyzed linear low density polyethylene

This article examines changes to the morphology of rotationally molded metallocene catalyzed linear low density polyethylene brought about by varying the cooling rate during processing. These changes in morphology lead to variations in the impact performance, which is reflected in the dynamic mechanical characteristics of the materials. Various analytical techniques are used in an attempt to explain the differences in impact behavior. Slow cooling is shown to result in high crystallinity, and in the formation of large spherulites, which in turn is detrimental to the impact performance of the material, particularly at low temperatures. The high crystallinity corresponds with a shift in the β transition of the material to a higher temperature, and is shown to result in a higher brittle–ductile transition. A case study was also carried out on samples from a finished part provided by an industrial molder, one section of which failed in a brittle manner when impact tested while the other failed in a ductile manner. Microscopy results showed that the brittle material had large spherulites at the inside surface, while the ductile material showed incipient degradation at this surface, which has previously been shown to be of benefit to impact strength in rotationally molded parts. Dynamic mechanical studies again showed a β transition at a higher temperature in the brittle samples. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1963–1971, 2006     

Preparation and surface activity of modified soy protein

A series of novel surfactants have been prepared by the reaction of hydrolyzed soy protein with alkyl succinic anhydride. These novel surfactants exhibit excellent surface active properties including surface tension, foaming, emulsifying, wetting power, and buffer ability. The hydrophobic modified protein exhibit more surface activity than original protein because of the enhanced hydrophobicity in structure. The increase in hydrophobic chain length leads to an increase in the surface activity. The surface tension reduction is correlated to the hydrophobicity of the modified molecule, which was determined by a fluorescent probe. In application on cotton bleaching procedures, these surfactants increase the whiteness of fabrics. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3498–3503, 2006     

Manufacturing and foaming of high melt viscosity of polypropylene by using electron beam radiation technology

The high melt viscosity of polypropylene was studied by grafting bifunctional monomers, 1,6‐hexanediol diacrylate (HDDA) and tripropylene glycol diacrylate (TPGDA), onto homopolypropylene (HPP) and random ter‐polypropylene (RTPP) under electron‐beam irradiation. Creation of the high‐melt‐viscosity polypropylene was possible at low radiation dosage and low monomer content, under a prohibition of both radiation degradation and homopolymerization. TPGDA monomer was more effective in increasing the melt viscosity of HPP compared with RTPP, whereas HDDA monomer was more effective for enhancing the melt viscosity of RTPP. Such different effects of monomers on melt viscosity may arise from different monomer structures, namely, TPGDA has additional three methyl groups, but HDDA has no methyl groups. Electron‐beam radiation technology, on an increase of the melt viscosity, was much more effective in HPP than RTPP, when compared with virgin polymers. Modified RTPP and HPP with high melt viscosity were capable of foaming with numerous fine cells, of which the modified HPP with 1.5 mmol TPGDA and 0.5 kGy could create more spherical foam cells and its bending strength was 1.5 times more than that of the foamed RTPP. POLYM. ENG. SCI., 46:431–437, 2006. © 2006 Society of Plastics Engineers.     

Comparative study of the physical aging of the epoxy systems BADGE n = 0/m‐XDA and BADGE n = 0/m‐XDA/PEI

The physical aging of the epoxy network consisting of a diglycidyl ether of bisphenol A, m‐xylylenediamine, and polyetherimide was studied by differential scanning calorimetry. The glass transition temperature and the variation of the specific heat capacities have been calculated using the method, based on the intersection of both enthalpy–temperature lines for glassy and liquid states. The apparent activation energy (E_H) was calculated using a single method that involved separate temperature and excess enthalpy dependency. All calorimetric data were compared with those obtained for the epoxy network without thermoplastic. thermoplastic. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3931–3935, 2006     

Preparation and properties of polyimide/silica hybrid composites based on polymer‐modified colloidal silica

A new type of polyimide/silica (PI/SiO₂) hybrid composite films was prepared by blending polymer‐modified colloidal silica with the semiflexible polyimide. Polyimide was solution‐imidized at higher temperature than the glass transition temperature (T_g) using 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐diaminodiphenyl ether (ODA). The morphological observation on the prepared hybrid films by scanning electron microscopy (SEM) pointed to the existence of miscible organic–inorganic phase, which resulted in improved mechanical properties compared with pure PI. The incorporation of the silica structures in the PI matrix also increased both T_g and thermal stability of the resulting films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2053–2061, 2006     

CaCO3/natural rubber latex nanometer composite and its properties

Calcium carbonate/natural rubber (NR) latex nanometer composites were prepared by adding nanometer CaCO₃ whose surface had been treated to natural rubber latex (NRL) before sulfuration. The physical, thermooxidative aging, and thermal degradation properties and the ultra‐microstructure were analyzed with a multipurpose material testing meter, a thermal analysis meter and a Philips XL‐30 SEM, respectively. The results showed that the structures and properties of nanometer composites could be clearly improved by NRL mixed with surface‐treated nanometer CaCO₃. The physical properties of the nanometer composites were best when the content of surface treatment agent was 2.5% (to nanometer CaCO₃), the nanometer CaCO₃/NRL content was 3:100, and the stirring time for treating the surface of the nanometer CaCO₃ was 20 min. Simultaneously, the thermooxidative aging resistance of the nanometer composites also was significantly improved. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3442–3447, 2006     

Synthesis and characterization of hydrophilic nanocomposite coating on glass substrate

Hydrophilic coatings based on 3‐glicidoxy propyl trimethoxy silane (GPTMS) and polyethylene glycol (PEG) were prepared with the incorporation of tetramethoxysilane (TMOS) and silica nanoparticle colloidal suspension by a sol–gel process. Characterization of the coatings has been performed by Fourier Transform Infrared (FTIR) and Attenuated Total Reflectance Infrared (ATR‐IR) techniques. Morphological properties were characterized by Scanning Electron Microscopy (SEM). The distribution of Si atoms in the hybrid system was obtained by Si mapping. The particle size in sol solution of the coating was measured by light scattering analyzer. Optical properties were characterized by using UV–vis spectrophotometer. The hydrophilicity of the coating was determined by contact angle measurements, and also the results have been confirmed by surface energy and water uptake investigations. The obtained results indicate that the surfactants affected the contact angles remarkably but did not change the transparency. It has been found that applying silica nano particles leads to coatings with different properties than those using TMOS, while siloxane contents were the same in these two set of coatings. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5322–5329, 2006     

Preparation and characterization of syndiotactic polystyrene/ethylene‐propylene copolymer blends

The reactive compatibilization of syndiotactic polystyrene (sPS)/oxazoline‐styrene copolymer (RPS)/maleic anhydride grafted ethylene‐propylene copolymer (EPR‐MA) blends is investigated in this study. First, the miscibility of sPS/RPS blends is examined by thermal analysis. The cold crystallization peak (T_cc) moved toward higher temperature with increased PRS, and, concerning enthalpy relaxation behaviors, only a single enthalpy relation peak was found in all aged samples. These results indicate that the sPS/RPS blend is miscible along the various compositions and RPS can be used in the reactive compatibilization of sPS/RPS/EPR‐MA blends. The reactive compatibilized sPS/RPS/EPR‐MA blends showed finer morphology than sPS/EPR‐MA physical blends and higher storage modulus (G') and complex viscosity (η*) when RPS contents were increased. Moreover, the impact strength of sPS/RPS/EPR‐MA increased significantly compared to sPS/EPR‐MA blend, and SEM micrographs after impact testing show that the sPS/RPS/EPR‐MA blend has better adhesion between the sPS matrix and the dispersed EPR‐MA phase. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2084–2091, 2002     

Synthesis and biological activity of phthalimide‐based polymers containing 5‐fluorouracil

The attachment of anticancer agents to polymers is a promising approach towards reducing the toxic side‐effects and retaining the potent antitumour activity of these agents. A new tetrahydrophthalimido monomer containing 5‐fluorouracil (ETPFU) and its homopolymer and copolymers with acrylic acid (AA) and with vinyl acetate (VAc) have been synthesized and spectroscopically characterized. The ETPFU contents in poly(ETPFU‐co‐AA) and poly(ETPFU‐co‐VAc) obtained by elemental analysis were 21 mol% and 20 mol%, respectively. The average molecular weights of the polymers determined by gel permeation chromatography were as follows: M_n = 8900 g mol^?1, M_w = 13 300 g mol^?1, M_w/M_n = 1.5 for poly(ETPFU); M_n = 13 500 g mol^?1, M_w = 16 600 g mol^?1, M_w/M_n = 1.2 for poly(ETPFU‐co‐AA); M_n = 8300 g mol^?1, M_w = 11 600 g mol^?1, M_w/M_n = 1.4 poly(ETPFU‐co‐VAc). The in vitro cytotoxicity of the compounds against FM3A and U937 cancer cell lines increased in the following order: ETPFU > 5‐FU > poly(ETPFU) > poly(ETPFU‐co‐AA) > poly(ETPFU‐co‐VAc). The in vivo antitumour activities of all the polymers in Balb/C mice bearing the sarcoma 180 tumour cell line were greater than those of 5‐FU and monomer at the highest dose (800 mg kg^?1). © 2002 Society of Chemical Industry