Physical Insight and Modelling for Lewis Number Effects on Turbulent Heat and Mass Transport in Turbulent Premixed Flames

The effects of global Lewis number on the behavior of Reynolds heat and mass fluxes in turbulent premixed flames are studied based on three-dimensional direct numerical simulation (DNS) of a number of statistically planar turbulent premixed flames with a global Lewis number ranging from Le = 0.34 to 1.2. For the same values of initial turbulent flow field parameters and duration of flame-turbulence interaction, it has been found that both Reynolds heat and mass fluxes may exhibit countergradient transport for flames with a Lewis number significantly smaller than unity; whereas predominantly gradient-type transport is obtained for flames with a Lewis number closer to unity. It is demonstrated that strong flame normal acceleration due to greater heat release in the low Lewis number flames acts to promote countergradient transport, and that the magnitude of the flame normal acceleration decreases with increasing Lewis number. Algebraic models for Reynolds heat and mass fluxes are proposed in which the effects of the Lewis number on flame normal acceleration are explicitly taken into account. The predictions of the new models are compared with DNS data, and the models are found to capture the influence of the Lewis number on turbulent scalar flux in a satisfactory manner for all the flames considered in this study.     

Adsorption Desalination Quenches Global Thirst

The search for fresh or potable water remains a pressing concern throughout many regions of the world. Although most of the Earth's surface is covered by oceans, the effort to provide for the world's inhabitants with fresh or potable water seems to be insurmountable; at least one billion people do not have access to clean and fresh water. The World Health Organization (WHO) reported that about 41% of the Earth's population lives in water-stressed areas, and the number of people in the water scarce regions may climb to 3.5 billion by the year 2025. Thus, innovative and cost-effective desalination technologies for producing fresh water are needed to provide practical solutions.     

Effects of Lewis number on flame surface density transport in turbulent premixed combustion

The transport of flame surface density (FSD) in turbulent premixed flames has been studied using a database obtained from Direct Numerical Simulation (DNS). Three-dimensional freely propagating developing statistically planar turbulent premixed flames have been examined over a range of global Lewis numbers from 0.6 to 1.2. Simplified chemistry has been used and the emphasis is on the effects of Lewis number on FSD transport in the context of Reynolds-averaged closure modelling. Under the same initial conditions of turbulence, flames with low Lewis numbers are found to exhibit counter-gradient transport of FSD, whereas flames with higher Lewis numbers tend to exhibit gradient transport of FSD. Stronger heat release effects for lower Lewis number flames are found to lead to an increase in the positive (negative) value of the dilatation rate (normal strain rate) term in the FSD transport equation with decreasing Lewis number. The contribution of flame curvature to FSD transport is found to be influenced significantly by the effects of Lewis number on the curvature dependence of the magnitude of the reaction progress variable gradient, and on the combined reaction and normal diffusion components of displacement speed. The modelling of the various terms of the FSD transport equation has been analysed in detail and the performance of existing models is assessed with respect to the terms assembled from corresponding quantities extracted from DNS data. Based on this assessment, suitable models are identified which are able to address the effects of non-unity Lewis number on FSD transport, and new or modified models are suggested wherever necessary.     

Incidence and genetic variability of Listeria species from three milk processing plants

The presence of Listeria in three milk processing environments as a potential source of milk contamination was assessed. Swab samples (n = 210) taken from milk processing plants were examined. Sample sites included the milk processing equipment, besides areas handling raw and pasteurized milk. The USDA Listeria-selective enrichment procedure was used to process the samples. Forty one (19.52%) Listeria isolates were recovered. The isolates were further subjected to biochemical and genotypic characterization. Out of 41 isolates, 16 (7.62%) were confirmed as Listeria monocytogenes, 2 (0.95%) as L. ivanovii, 19 (9.05%) as L. innocua. 1 (0.48%) as L. seeligeri and 3 (1.43%) as L. grayi. All the L. monocytogenes isolates were positive for the hlyA gene. PCR based serotyping revealed all L. monocytogenes to be of 1/2a, 1/2c, 3a and 3c serovar group. AscI and ApaI restriction analysis yielded four PFGE clusters for 16 L. monocytogenes isolates obtained from raw milk collector, milk silos, buttermilk mixer, cheese and other milk product processor. No predominant PFGE cluster was observed among these L. monocytogenes isolates. The main sources of L. monocytogenes were found to be raw milk collector and milk silos. In the present study L. monocytogenes was isolated from milk and milk products processing plants which could cross-contaminate the processed products and may possess a potential threat to public health.     

Microstructural evolution and hardness of in situ Al-4.5Cu-5TiB2 composite processed by multiple roll passes in mushy state

In situ Al-4.5Cu-5TiB₂ composite has been processed through stir casting method, in which, the TiB₂ particles have been precipitated in situ by mixed salt route involving reactions between K₂TiF₆ and KBF₄.The as-cast specimens containing 20 volume percent liquid content have been subjected to three mushy state roll passes, each leading to 5 percent reduction in thickness. The grain structure has been found to be globular in the mushy state rolled composites. Measurements along the cross-section have shown decrease in average grain size and increase in hardness, as one proceeds along the direction of rolling. On the other hand, grain size and hardness have been found to be more or less similar, when compared for sections perpendicular to the rolling direction.     

Modelling of a downdraft biomass gasifier with finite rate kinetics in the reduction zone

A model of a downdraft gasifier has been developed based on chemical equilibrium in the pyro‐oxidation zone and finite rate kinetic‐controlled chemical reactions in the reduction zone. The char reactivity factor (C_RF) in the reduction zone, representing the number of active sites on the char and its degree of burn out, has been optimized by comparing the model predictions against the experimental results from the literature. The model predictions agree well with the temperature distribution and exit gas composition obtained from the experiments at C_RF=100. A detailed parametric study has been performed at different equivalence ratios (between 2 and 3.4) and moisture content (in the range of 0–40%) in the fuel to obtain the composition of the producer gas as well as its heating value. It is observed that the heating value of the producer gas increases with the increase in the equivalence ratio and decrease in the biomass moisture content. The effect of divergence angle of the reduction zone geometry (in the range of 30–150°) on the temperature and species concentration distributions in the gasifier has been studied. An optimum divergence angle, giving the best quality of the producer gas, has been identified for a particular height of the reduction zone. Copyright © 2009 John Wiley & Sons, Ltd.     

Investigation of terminalia (Terminalia belerica Robx.) seed oil as prospective biodiesel source for North-East India

Terminalia (Terminalia belerica Robx.) is available in the northeastern region of India. The fruit of terminalia has some medicinal value and its kernel contains 43% oil. The prospect of terminalia oil for biodiesel production is investigated with reference to some relevant properties. The fatty acid profile of oil extracted from terminalia is found comparable with similar seed oils attempted for biodiesel production in this region. Terminalia oil contains 32.8% palmitic acid, 31.3% oleic acid, and 28.8% linoleic acid. The calorific value and kinematic viscosity of terminalia oil are 37.50 MJ/kg and 25.60 cSt, respectively. The calorific value and cetane number of terminalia FAME are within the acceptable limit of the EN 14214 standard. However, the flash point of terminalia FAME (90 °C) is relatively lower than the minimum required standard. Overall, the properties of biodiesel obtained from terminalia seed conform to the existing biodiesel standard. In addition to assisting the national biodiesel mission, the extension and regeneration of forest areas through terminalia planting would help us to curb the seemingly irreversible trend of de-forestation in the northeast region of India.     

The electro-adsorption chiller: a miniaturized cooling cycle with applications to micro-electronics

A novel modular and miniature chiller is proposed that symbiotically combines adsorption and thermoelectric cooling devices. The seemingly low efficiency of each cycle individually is overcome by an amalgamation with the other. This electro-adsorption chiller incorporates solely existing technologies. It can attain large cooling densities at high efficiency, yet is free of moving parts and comprises harmless materials. The governing physical processes are primarily surface rather than bulk effects, or involve electron rather than fluid flow. This insensitivity to scale creates promising applications in cooling personal computers and other microelectronic appliances.     

A unified scheme for adaptive stroke-based rendering

This paper presents a comprehensive scheme for automatically generating a broad class of artistic illustrations from photographs. Using strokes as the major building blocks, our system optimizes the stroke attributes subject to the desired rendering style. The stroke attributes are computed adaptively to enable importance-based control of the abstraction level at each pixel. We propose a novel outline detection and refinement paradigm called edge painting to construct an outline map, and from which to derive the pixel-wise importance. We also introduce an adaptive bilateral filter to adaptively guide the curved stroke directions based on the importance map. Given the outline, importance, and direction maps, the system creates the illustration via selecting the representative colors, setting the style parameters, and optimizing the stroke attributes based on simulated annealing. The experimental results show that our scheme facilitates automatic production of artistic illustrations in a wide range of rendering styles.     

Effect of ash on maximum thickness of plastic layer of coals

A study of the effect of ash yield on the maximum thickness of the plastic layer (MTPL) of some coking coals (as measured by the Sapozhnikov plastometer) has revealed that with an increase in the former the latter in general decre?es. A rectilinear relation approximately exists between the ash percentage (dry basis) and log MTPL values of coals. For the samples studied, a multiple correlation incorporating the rank factor was found to be unnecessary. Higher Fe₂O₃ and SO₃ contents from the coal were found to be associated with higher MTPL values.