Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

ESR Refining Potential for Titanium Alloys using a CaF2‐based Active Slag

Since the end of the Cold War and due to the needs to produce titanium more cost‐efficient and thus more attractive for its civilian use, the electroslag remelting (ESR) process has become an increasingly important topic of international research programmes, because titanium and titanium aluminides can be chemically refined by ESR in some degree. Using ESR, titanium turnings from machining steps and scrap from foundries can be remelted, refined and provided as secondary titanium for the market at relatively favourable prices. This article investigates the removability of the main impurities out of titanium and titanium‐aluminium alloys by electroslag remelting using the active slag system CaF₂‐Ca‐(CaO). Thermochemical and kinetic aspects of the ESR process are considered.     

Symmetric BEM formulations for 2-D steady-state and transit potential problems

This paper presents a new concept for symmetric boundary element method (SBEM) applicable to 2-D steady-state and transit potential problems. Two kinds of SBEM formulations are derived. Symmetry is obtained simply through matrix manipulation, and no hypersingularity appears. Therefore, SBEM is much easier than the traditional symmetric Galerkin BEM. Compared with the traditional asymmetric BEM, the present SBEM can reduce the computational cost for time domain problems only. However, when applied to BEM/FEM coupling procedure, SBEM can reduce the computational cost for both steady-state and time domain problems. Three numerical examples are included to illustrate the effectiveness and accuracy of the present formulations.     

Polygonal extrusion

A sweeping operation called polygonal extrusion is defined to improve the modeling power of CSG-based modeling. It is assumed that a 2D cross-sectional polygon (sweeping polygon) moves in space while its containing plane is kept orthogonal to the tangent direction of the trajectory curve, a planar polygonal chain having no self-intersections. The objective of the paper is to compute the boundary of the swept volume of the sweeping polygon as a set of polygons (or triangles). The most significant challenge to accomplishing this objective is the problem of trimming the swept volume. To solve the trimming problem, 2D-curve offsetting methods are employed. Two algorithms are presented for polygonal extrusion that are based on different offsetting methods, the Voronoi diagram and PWID offset. The proposed algorithms have been implemented and tested with various examples. Published online: 28 January 2003     

Squeeze-film effects in MEMS devices with perforated plates for small amplitude vibration

Squeeze-film effects of perforated plates for small amplitude vibration are analyzed through modified Reynolds equation (MRE). The analytical analysis reckons in most important influential factors: compressibility of the air, border effects, and the resistance caused by vertical air flow passing through perforated holes. It is found that consideration of air compressibility is necessary for high operating frequency and small ratio of the plate width to the attenuation length. The analytical results presented in this paper agree with ANSYS simulation results better than that under the air incompressibility assumption. The analytical analysis can be used to estimate the squeeze-film effects causing damping and stiffness added to the system. Since the value of Reynolds number involved in this paper is low (< 1), inertial effects are neglected.     

Pupils' recall of an interactive storybook on CD-ROM

Abstract This small-scale study compares two groups of Year 4 (8/9 year-old) pupils either reading or playing an interactive storybook . The study considered pupils' recall of propositions, which formed the story setting and episodes, and of micro-propositions and characters' names, and pupils' responses to inferential items derived from the 'interactive storybook'. The study indicates that, whether reading or playing, pupils' recall of the story setting was sound, but pupils who had read the interactive storybook demonstrated greater recall of the story event structure than those who had engaged in interactive picture-play. Pupils who had played the interactive storybook demonstrated significantly greater recall of micro-propositions and names.     

Exploiting ILP, TLP, and DLP with the polymorphous trips architecture

The Tera-op reliable intelligently adaptive processing system (TRIPS) architecture seeks to deliver system-level configurability to applications and runtime systems. It does so by employing the concept of polymorphism, which permits the runtime system to configure the hardware execution resources to match the mode of execution and demands of the compiler and application.     

What's the use of being happy? Mood states, useful objects, and repetition priming effects.

Two experiments involving 99 undergraduate participants sought to examine the influence of mood states on encoding speed within lexical decision and pronunciation tasks. Mood states were measured naturalistically in Experiment 1 and manipulated in Experiment 2. Stimuli consisted of nouns representing useful (e.g., food) and nonuseful (e.g., lint) objects. Mood states had no implications for initial encoding speed. However, when the same words were presented a 2nd time (i.e., repeated), happy individuals displayed a tendency to encode useful words faster than nonuseful ones. Thus, mood states influenced repetition priming on the basis of stimulus valence. The authors propose that happiness sensitizes individuals to useful or rewarding objects, which in turn creates a stronger memory trace for such stimuli in the future. (PsycINFO Database Record (c) 2010 APA, all rights reserved)