Pack cementation process for the formation of refractory metal modified aluminide coatings on nickel-base superalloys

The vapour phase compositions of a series of pack powder mixtures containing elemental Al and Hf or W powders as depositing sources and CrCl₃·6H₂O or AlF₃or CrF₃as activators were analysed in an attempt to further develop the pack cementation process to codeposit Al and Hf or W to form diffusion coatings on nickel base superalloys. The results suggested that Al could be codeposited with Hf, but not with W, from the vapour phase. Compared with both AlF₃and CrF₃, CrCl₃·6H₂O has been shown to be a more suitable activator for codepositing Al with Hf. The optimum coating temperature was identified to be in the range of 1050°C to 1150°C. Based on the thermochemical analysis, a series of coating deposition studies were undertaken, which confirmed that codeposition of Al and Hf could be achieved at a deposition temperature of 1100°C in the CrCl₃·6H₂O activated packs containing elemental Al and Hf powders. The coating obtained had a multilayer structure consisting of a Ni₇Hf₆Al₁₆top layer and a NiAl layer underneath, followed by a diffusion zone, which revealed that the coating was formed by the outward Ni diffusion. It is suggested that the compositions suitable for codeposition of Al and Hf could be effectively identified by comparing the vapour pressures of HfCl₄and HfCl₃with that of AlCl in the packs activated by chloride salts. It has also been experimentally demonstrated that, although W could not be deposited from the vapour phase, a high volume of fine W particles can be entrapped into the outer NiAl coating layer formed by the outward Ni diffusion using a modified pack configuration. This leads to the formation of a composite coating layer with W particles evenly distributed in a matrix of NiAl. It is suggested that this modified pack process could be similarly applied to develop nickel aluminide coatings containing other refractory metals that may not be codeposited with Al from the vapour phase.     

The extended quadratic residue code is the only (48,24,12) self-dual doubly-even code

An extremal self-dual doubly-even binary (n,k,d) code has a minimum weight d=4/spl lfloor/n/24/spl rfloor/+4. Of such codes with length divisible by 24, the Golay code is the only (24,12,8) code, the extended quadratic residue code is the only known (48,24,12) code, and there is no known (72,36,16) code. One may partition the search for a (48,24,12) self-dual doubly-even code into three cases. A previous search assuming one of the cases found only the extended quadratic residue code. We examine the remaining two cases. Separate searches assuming each of the remaining cases found no codes and thus the extended quadratic residue code is the only doubly-even self-dual (48,24,12) code.     

Switched-Current Filters Revisited: Square-Root Domain Sampled-Data Filters

In this brief, the well-known switched-current (SI) filtering technique is revisited using the concept of the square-root domain (SRD) filtering. It is proved that SI filters are a subclass of the SRD filters, where sampled-data signal processing is performed. This is achieved by considering typical lossless and lossy SRD sampled-data integrator configurations, using a set of complementary SRD operators which are based on the quadratic I-V relationship of MOS transistor operated in the saturation. Circuit examples are given, where linear-domain integrator and third-order filter configurations were derived using appropriate SRD sampled-data building blocks     

Breaking a remote user authentication scheme for multi-server architecture

Lin et al., (2003) proposed a remote user authentication scheme for multi-server architecture. In this paper, we breaks this scheme by giving an attack. Our attack allows an adversary to impersonate any user in the system, as long as a single authentication message of that user is observed.     

Parametric effects on the transient Voltage performance of a DC superconducting cable

The objective of this work was to determine the significant parameters of a 3-GW 200-kV dc superconducting cable system which influence the transient voltage distribution in the various parts of the cable. The cable system consists of four coaxial metallic cylinders. It was found that the dielectric constant and the electrical resistivity of the soil significantly affect the severity of the transient voltages; lower dielectric constant and higher resistivity of the soil will increase the magnitudes of the transient voltages by increasing the earth-return impedance. It was also found that the effect of the conductor internal impedances of the cable is insignificant. Shorting the coaxial cylinders of the cryogen flow and the cryostat will lessen the severity of the transient voltages. Grounding the second, third, and fourth cylinders at regular intervals with low-impedance grounding impedance will also improve the transient performance of the cable. More research is needed to evaluate these procedures.     

Protecting local access telecommunications networks: Toward a minimum-cost solution

The problem of designing fibre-optic networks for local-access telecommunications generates (at least) three non-trivial subproblems. In the first of these subproblems one must determine how many fibre-optic cables (fibres) are required at either end of a street. In the next subproblem a minimum-cost network must be designed to support the fibres. The network must also provide distinct paths from either end of the street to the central exchange(s). Finally, the fibre-optic cables must be placed in protective covers. These covers are available in a number of different sizes, allowing some flexibility when covering each section of the network. In this paper we describe a dynamic programming (DP) formulation for finding a minimum-cost (protective) covering for the network (the third of the subproblems). This problem is a generalised set covering problem with side constraints and is further complicated by the introduction of fixed and variable welding costs. The DP formulation selects covers along each arc (in the network), but cannot exactly model the fixed costs and so does not guarantee optimality. We also describe an integer programming (IP) formulation for assessing the quality of the DP solutions. The cost of the networks constructed by the IP model is less than those designed using the DP model, but the saving is not significant for the problems examined (less than 0.1%). This indicates that the DP model will generally give very good solutions. Furthermore, as the problem dimensions grow, DP gives significantly better solution times than IP.     

Fracture response of fibre-reinforced materials with macro/microcrack damage using the Boundary Element Technique

The Boundary Element Method (BEM) incorporating the Embedded Cell Approach (ECA) has been used to analyse the effects of constituent material properties, fibre spatial distribution and microcrack damage on the localised behaviour of transversely fractured, unidirectional fibre-reinforced composites. Three specific composites, i.e., glass fibre reinforced polyester, carbon fibre reinforced epoxy and a glass-carbon hybrid, are considered. The geometrical structures examined were perfectly periodic, uniformly spaced fibre arrangements in square and hexagonal embedded cells. In addition, numerical simulations were also conducted using embedded cells containing randomly distributed fibres. The models involve both elastic fibres and matrix, with the interfaces between the different phases being fully bonded. The results indicate that the constituent material properties (two phase composite) and spatial distribution have a significant effect on the localised stress distributions around the primary crack tip. However, the strain energy release rate associated with crack propagation is predominantly influenced by the material composition. The three-phase hybrid composite exhibited an apparent intermediate fracture toughness value, compared to the all-glass and all-carbon models. Furthermore, the strain energy release rate for the macrocrack lowers as it enters a zone of localised damage (microcracking). The presence of microcracks relaxes the stress field, which can result in a significant reduction in the energetics of the primary crack.     

TEM Studies of High Temperature Corrosion Behaviour of TiAl Intermetallics with Surface Modifications

The oxidation/sulphidation behaviour of a Ti‐46.7Al‐1.9W‐0.5Si alloy with a TiAl₃ diffusion coating was studied in an environment of H₂/H₂S/H₂O at 850^oC. The kinetic results demonstrate that the TiAl₃ coating significantly increased the high temperature corrosion resistance of Ti‐46.7Al‐1.9W‐0.5Si. The SEM, EDX, XRD and TEM analysis reveals that the formation of an Al₂O₃ scale on the surface of the TiAl₃‐coated sample was responsible for the enhancement of the corroison resistance. The Ti‐46.7Al‐1.9W‐0.5Si alloy was also modified by Nb ion implantation. The Nb ion implanted and as received sampels were subjected to cyclic oxidation in an open air at 800^oC. The Nb ion implantation not only increased the oxidation resistance but also substantially improved the adhesion of scale to the substrate.