Benchmark simulation Model no 2 in Matlab-simulink: towards plant-wide WWTP control strategy evaluation.

In this paper, implementation of the Benchmark Simulation Model No 2 (BSM2) within Matlab-Simulink is presented. The BSM2 is developed for plant-wide WWTP control strategy evaluation on a long-term basis. It consists of a pre-treatment process, an activated sludge process and sludge treatment processes. Extended evaluation criteria are proposed for plant-wide control strategy assessment. Default open-loop and closed-loop strategies are also proposed to be used as references with which to compare other control strategies. Simulations indicate that the BM2 is an appropriate tool for plant-wide control strategy evaluation.     

Analysis of phosphorus removal and anaerobic selector performance in a full-scale activated sludge process in Singapore.

This paper analyses the performance of the anaerobic selector (A/O process) in a full-scale activated sludge process receiving mostly industrial sewage discharge (> 60%) in Singapore. In addition to the sludge settleability, enhanced biological phosphorus removal (EBPR) was studied. The sludge volume index (SVI) reduced from 200 to 80 ml g(-1) and foaming was suppressed significantly, indicating the effectiveness of the anaerobic selector in improving sludge settleability. The phosphorus removal efficiency was 66%, and 7.5 mg HAc-COD was consumed per mg PO4(3-) -P removed. In the anaerobic compartment, 31% of the SCOD and 73% of the acetic acid in the settled sewage were removed with PO4(3-) -P release of 14.1 mg PO4(3-)-P l(-1). The linear correlation between PO4(3-) -P release in the anaerobic compartment and PO4(3-) -P uptake in the aerobic compartment indicates that there is about 0.8 mg PO4(3-) -P release in the anaerobic compartment per mg PO34(3-) -P uptake in the aerobic compartment. The fates of volatile fatty acids (VFAs) and its short chain acids (SCAs) in the process were studied and discussed.     

Enhanced sludge conditioning by enzyme pre-treatment: comparison of laboratory and pilot scale dewatering results.

The effect of enzyme pre-treatment on dewaterability of anaerobically digested sludge was investigated at both laboratory and pilot scale. Our results revealed a significant increase in cake solid content (27% cake solids compared to 18% without enzyme pre-treatment), using an enzyme dose of only 20 mg/L. In order to assess practical application, enzyme pre-treatment was applied at the Wilmington, Delaware (U.S.) wastewater treatment plant, using a pilot-scale centrifuge. However, the efficiency reached in laboratory scale could not be obtained in pilot scale, where the final cake solids content did not exceed 20%. Centrifuge and belt filter press (simulated by Crown Press) dewatering were compared in terms of the process efficiencies in the absence and presence of enzyme pre-treatment. Possible factors that might cause the differences were tested by experimental and statistical comparisons. Results indicated that the higher shear applied in centrifugation is responsible for the lack of improved cake solids. The network strength of sludge determined by rheological measurements revealed that enzymatic treatment weakens the gel structure of the sludge floc through the hydrolysis of extracellular polymeric substances; this allows improved dewatering by filtration processes, but leads to floc deterioration when subjected to high shear during centrifugation.     

Tracking influent inorganic suspended solids through wastewater treatment plants.

From an experimental and theoretical investigation of the continuity of influent inorganic suspended solids (ISS) along the links connecting the primary settling tank (PST), fully aerobic or N removal activated sludge (AS) and anaerobic and aerobic sludge digestion unit operations, it was found that the influent wastewater (fixed) ISS concentration is conserved through primary sludge anaerobic digestion, activated sludge and aerobic digestion unit operations. However, the measured ISS flux at different stages through a series of wastewater treatment plant (WWTP) unit operations is not equal to the influent ISS flux, because the ordinary heterotrophic organisms (OHO) biomass contributes to the ISS flux by differing amounts depending on the active fraction of the VSS solids at that stage.     

Sampling for representative micropollutant loads in sewer systems.

Most commercially available auto-sampling devices do not support a continuous flow-proportional sampling mode, which would conceptually be the best for collecting representative composite samples. Instead different discrete sampling modes are available. Household chemicals can show considerable random short-term variations. With the anticorrosive benzotriazole, relating to a middle-frequent household activity, we show that, besides an accurate flow meter, mainly three factors are decisive for the representativeness of a substance's average load: the substance's load pattern, the sampling frequency and the length of the composite sample. When the sampling intervals are 10 minutes or longer, errors in the order of +/-40% (standard deviation) or more have to be accepted, if the substance of interest is contained in a low number of wastewater pulses (i.e., the level of household activity). This particularly holds true for specific pharmaceuticals e.g. carbamazepine. Ammonium would be less critical, because it relates to a larger number of sources in the same catchment.     

Dewatered alum sludge: a potential adsorbent for phosphorus removal.

Alum sludge refers to the by-product from the processing of drinking water in water treatment works. In this study, groups of batch experiments were designed to identify the characteristics of dewatered alum sludge for phosphorus adsorption. Air-dried alum sludge (moisture content 10.2%), which was collected from a water treatment works in Dublin, was subjected to artificial P-rich wastewater adsorption tests using KH2PO4 as a model P source. Adsorption behaviours were investigated as a function of amount and particle size of alum sludge, pH of solution and adsorption time. The results have shown that pH plays a major role not only in the adsorption process but also in the adsorption capacity. With regard to adsorption capacity, this study reveals the Langmuir adsorption isotherm being the best fit with experimental data (R2 = 0.98-0.99). The maximum adsorption capacities range from 0.7 to 3.5 mg-P/g when the pH of the synthetic P solution was varied from 9.0 to 4.3, accordingly. The outcome of this study indicated that alum sludge is suitable for use as an adsorbent for removal of phosphate from wastewater.     

One-dimensional GIS-based model compared with a two-dimensional model in urban floods simulation.

A GIS-based one-dimensional flood simulation model is presented and applied to the centre of the city of N?mes (Gard, France), for mapping flow depths or velocities in the streets network. The geometry of the one-dimensional elements is derived from the Digital Elevation Model (DEM). The flow is routed from one element to the next using the kinematic wave approximation. At the crossroads, the flows in the downstream branches are computed using a conceptual scheme. This scheme was previously designed to fit Y-shaped pipes junctions, and has been modified here to fit X-shaped crossroads. The results were compared with the results of a two-dimensional hydrodynamic model based on the full shallow water equations. The comparison shows that good agreements can be found in the steepest streets of the study zone, but differences may be important in the other streets. Some reasons that can explain the differences between the two models are given and some research possibilities are proposed.     

Differentiation of Romashkino crude oils according to biomarker hydrocarbon parameters

The trends in composition of higher biomarker hydrocarbons (steranes and tri-, tetra-, and pentacyclic terpanes) in crude oils from diachronous producing complexes of deposits of the Romashkino oil field, which occurs in the central part of the South Tatarian arch, were studied. On the basis of variations in molecular biomarker parameters that reflect the type of source organic matter and the facies conditions of its accumulation and early diagenesis, the oils are classified with three groups.     

HIGHER PLANT BIOMARKERS IN PALEOGENE CRUDE OILS FROM THE YUFUTSU OIL-AND GASFIELD AND OFFSHORE WILDCATS, JAPAN

Geochemical investigation of Paleogene oils from the onshore Yufutsu oil- and gasfield, southern Hokkaido, and from two nearby offshore wells, revealed the presence of numerous biomarkers of higher plant origin. Biomarkers in the oils belong to different groups of both angiosperm and gymnosperm origin; they include bicyclic sesquiterpanes, diterpanes, and triterpanes and their aromatized counterparts, which suggests a terrestrial origin for the oils. The oils were characterized as having a high wax content, a low content of organosulphur compounds, a high pristane/phytane ratio, and a low C₂₇/(C₂₇+C₂₉) sterane ratio.
Although the oils from on- and offshore Southern Hokkaido are similar in their geochemical composition, notable differences were observed in the biomarker signature of both saturate and aromatic fractions. The oils from the offshore wells appeared to have a greater abundance of higher plant biomarkers compared to those from the Yufutsu field, suggesting an enrichment in higher plant components. Differences in biomarker fingerprint could not be linked to the maturity effect, since the oils appeared to be of similar maturity levels, corresponding to the late stage of the oil window (0.9–1.2%, Rc). The differences in the biomarker signatures between the oils from the Yufutsu field and the offshore wells are likely to be due to facies variations in source organic matter, resulting from differences in the quantity and quality of land plant input.     

PETROLEUM POTENTIAL, THERMAL MATURITY AND THE OIL WINDOW OF OIL SHALES AND COALS IN CENOZOIC RIFT BASINS, CENTRAL AND NORTHERN THAILAND

Oil shales and coals occur in Cenozoic rift basins in central and northern Thailand. Thermally immature outcrops of these rocks may constitute analogues for source rocks which have generated oil in several of these rift basins. A total of 56 oil shale and coal samples were collected from eight different basins and analysed in detail in this study. The samples were analysed for their content of total organic carbon (TOC) and elemental composition. Source rock quality was determined by Rock‐Eval pyrolysis. Reflected light microscopy was used to analyse the organic matter (maceral) composition of the rocks, and the thermal maturity was determined by vitrinite reflectance (VR) measurements. In addition to the 56 samples, VR measurements were carried out in three wells from two oil‐producing basins and VR gradients were constructed. Rock‐Eval screening data from one of the wells is also presented. The oil shales were deposited in freshwater (to brackish) lakes with a high preservation potential (TOC contents up to 44.18 wt%). They contain abundant lamalginite and principally algal‐derived fluorescing amorphous organic matter followed by liptodetrinite and telalginite (Botryococcus‐type). Huminite may be present in subordinate amounts. The coals are completely dominated by huminite and were formed in freshwater mires. VR values from 0.38 to 0.47%R_o show that the exposed coals are thermally immature. VR values from the associated oil shales are suppressed by 0.11 to 0.28%R_o. The oil shales have H/C ratios >1.43, and Hydrogen Index (HI) values are generally >400 mg HC/g TOC and may reach 704 mg HC/ gTOC. In general, the coals have H/C ratios between about 0.80 and 0.90, and the HI values vary considerably from approximately 50 to 300 mg HC/gTOC. The HI_max of the coals, which represent the true source rock potential, range from ～160 to 310 mg HC/g TOC indicating a potential for oil/gas and oil generation. The steep VR curves from the oil‐producing basins reflect high geothermal gradients of ～62°C/km and ～92°C/km. The depth to the top oil window for the oil shales at a VR of ～0.70%R_o is determined to be between ～1100 m and 1800 m depending on the geothermal gradient. The kerogen composition of the oil shales and the high geothermal gradients result in narrow oil windows, possibly spanning only ～300 to 400 m in the warmest basins. The effective oil window of the coals is estimated to start from ～0.82 to 0.98%R_o and burial depths of ～1300 to 1400 m (～92°C/km) and ～2100 to 2300 m (～62°C/km) are necessary for efficient oil expulsion to occur.