NUMERICAL ANALYSIS OF THE EFFECTS OF LOCAL HYDRODYNAMICS ON MASS TRANSFER IN HETEROGENEOUS POROUS MEDIA

Many engineering problems require the estimation of mass transfer coefficients in porous materials. In heterogeneous materials or in cases where mass transfer sites are not spatially uniform, empirical equations for mass transfer coefficients vary widely, and the origin of these differences is not well understood. In this article, we use a stochastic algorithm to model mass transfer from single particles in a two-dimensional heterogeneous packed bed. The computed mass transfer coefficients are used to generate a distribution of local Peclet numbers in the bed. Detailed hydrodynamics are then used to interpret variations in the local Peclet number. The results show clear relationships between pore structure, streamline patterns, and mass transfer rates.     

A broadband PHEMT MMIC distributed doubler using high-pass drain line topology

A broadband frequency doubler, based on distributed amplifier techniques, has been designed to operate from 11 to 21 GHz. In order to reject the fundamental signal over a broadband frequency range, the conventional low-pass drain line structure was replaced with the high-pass structure. This topology can suppress fundamental signals over broadband without any balanced structure so that the chip size can be more compact. Measured conversion losses of better than 10 dB from 11 to 21 GHz input frequencies are achieved with fundamental signal rejection better than 12 dB. To the best of our knowledge, this is the first demonstration of distributed doubler using the high-pass drain line topology.     

Engineering Computation and Analysis of Enhancing Efficiency for Folded Waveguide TWT in MMW

Large signal operating equations in TWT have been solved by numerical solve method. The relations between interaction efficiency and design parameters in TWT are analyzed. A fast engineering design method of enhancing efficiency for folded waveguide TWT by velocity resynchronization is described. The computation is shown that the efficiency of Ka-band folded waveguide TWT with double taper can be enhanced over twice as original tube. This method of approach is very useful for tube designer.     

S1240一次呼叫转移命令不成功故障的排除

对S1240交换机一次呼叫转移命令不成功故障排除的过程进行了分析。     

Associative properties of perfluorooctyl end‐functionalized polystyrene–poly(ethylene oxide) diblock copolymers

The synthesis of 2,2,3,3‐tetrahydro‐perfluoroundecanoyl end‐functionalized polystyrene–poly(ethylene oxide) block (PS‐block‐PEO‐R_F) copolymers and their matching PS‐block‐PEO diblock copolymers was carried out by sequential anionic polymerization. Viscometry and ¹⁹F NMR studies show that the PS‐block‐PEO copolymers, in contrast to their matching PS‐block‐PEO‐R_F copolymers, exhibit a micellar rather than the associative behavior seen for the latter. However, the presence of an excess of fluorinated acid, used for end‐functionalization, produces a reduction of the associative behavior above the overlap concentration, with the fluorinated acid acting like a surfactant. A competition may also occur between PS—and R_F—mediated micellization. Copyright © 2004 Society of Chemical Industry     

Methacryloxyethyl phosphate‐grafted expanded polytetrafluoroethylene membranes for biomedical applications

Expanded polytetrafluoroethylene (ePTFE) membranes were modified by graft copolymerization with methacryloxyethyl phosphate (MOEP) in methanol and 2‐butanone (methyl ethyl ketone (MEK)) at ambient temperature using gamma irradiation. The effect of dose rate (0.46 and 4.6 kGy h^?1), monomer concentration (1–40 %) and solvent were studied and the modified membranes were characterized by weight increase, X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). XPS was used to determine the % degree of surface coverage using the C? F (ePTFE membrane) and the C? C (MOEP graft copolymer) peaks. Grafting yield, as well as surface coverage, were found to increase with increasing monomer concentration and were significantly higher for samples grafted in MEK than in methanol solution. SEM images showed distinctly different surface morphologies for the membranes grafted in methanol (smooth) and MEK (globular), hence indicating phase separation of the homopolymer in MEK. We propose that in our system, the non‐solvent properties of MEK for the homopolymer play a more important role than solvent chain transfer reactions in determining grafting outcomes. Copyright © 2005 Society of Chemical Industry     

钻机绞车滚筒体的窄间隙埋弧焊

针对钻机绞车滚筒体采用手工电弧焊工人劳动强度大、焊接效率低、质量不稳定及返修率高等问题,研制了钻机绞车滚筒体窄间隙埋弧焊专机。该专机由ESAB—A2埋弧焊电源和焊接小车、窄间隙焊头、滚轮架、防窜装置、旋转地线夹、三维焊接工作台、焊剂自动回收机组成。使用表明,采用该焊机焊接的滚筒体焊缝质量完全符合设计要求,合格率100%,焊接效率比原来提高6倍。每件滚筒体的焊接可降低人工成本约80%。     

Bias dependence of high-frequency noise in heterojunction bipolar transistors

Hawkins' isothermal model developed to study noise in bipolar junction transistors (BJTs) is modified to investigate bias-dependent noise in heterojunction bipolar transistors (HBTs) by incorporating thermal effects. It is shown that the inclusion of thermal effects into the high-frequency noise model of HBTs is necessary as the temperature of the device may become very different from the ambient temperature, especially at high bias current. Calculation of the noise figure by including the thermal effect shows that the isothermal calculation may underestimate the noise figure at high bias current. It is observed that noise at low bias is ideality factor n dependent whereas high bias noise is insensitive to the variation of n. Moreover, the common base current gain plays a major role in the calculation of the minimum noise figure. The excellent fit obtained between the theoretical calculation and the measured data are attributed to the inclusion of the bias-dependent junction heating as well as C/sub De/ and C/sub bc/ into the present calculation.     

In situ polymerization and characterization of polyester‐based polyurethane/nano‐silica composites

Polyester‐based polyurethane/nano‐silica composites were obtained via in situ polymerization and investigated by Fourier‐transform infrared spectroscopy (FTIR), or FTIR coupled with attenuated total reflectance (FTIR‐ATR), Transmission electron microscopy (TEM), atomic force microscopy (AFM), an Instron testing machine, dynamic mechanical analysis (DMA) and ultraviolet‐visible spectrophotometry (UV‐vis). FTIR analysis showed that in situ polymerization provoked some chemical reactions between polyester molecules and nano‐silica particles. FTIR‐ATR, TEM and AFM analyses showed that both surface and interface contained nano‐silica particles. Instron testing and DMA data showed that introducing nano‐silica particles into polyurethane enhanced the hardness, glass temperature and adhesion strength of polyurethane to the substrate, but also increased the resin viscosity. UV‐vis spectrophotometry showed that nano‐silica obtained by the fumed method did not shield UV radiation in polyurethane films. Copyright © 2003 Society of Chemical Industry