单壁碳纳米管的制备及生长特性研究

采用Fe/MgO作为催化剂 ,催化裂解CH4制备了较纯的单壁碳纳米管 ,用TEM和Raman对碳纳米管进行了表征 ,对不同生长温度下制备的碳纳米管Raman径向呼吸振动峰 (RBM)进行了分析 ,研究了生长温度对单壁碳纳米管生长特性和结构特性的影响     

Industrialization of High Performance Sintered NdFeB Magnets

Sintered Nd-Fe-B magnet was manufactured by advanced equipment via a SC (Strip casting) technology.It has integrative performance.     

Deposition and Properties of Superconducting MgB2 Thin Films

The recently discovered superconductor MgB₂ with T _c at 39 K has great potential in superconducting electronics. In this paper, we review the deposition techniques used for MgB₂ thin films in the light of a thermodynamic study of the Mg-B system with the calculation of phase diagrams (CALPHAD) modeling technique. This thermodynamic study identifies a growth window in the pressure–temperature phase diagram, in which the magnesium pressure is very high for likely in situ growth temperatures. A Hybrid Physical–Chemical Vapor Deposition (HPCVD) technique that successfully achieves such a high Mg pressure is shown to produce in situ epitaxial MgB₂ thin films with bulk superconducting properties.     

Prediction of the energy dissipation rate in ductile crack propagation

In this paper, energy dissipation rate D vs. Δa curves in ductile fracture are predicted using a ‘conversion’ between loads, load‐point displacements and crack lengths predicted by NLEFM and those found in real ELPL propagation. The NLEFM/ELPL link was recently discovered for the DCB testpiece, and we believe it applies to other cracked geometries. The predictions for D agree with experimental results. The model permits a crack tip toughness R(Δa) which rises from J_c and saturates out when (if) steady state propagation is reached after a transient stage in which all tunnelling, crack tip necking and shear lip formation is established. J_R is always greater than the crack tip R(Δa) and continues to rise even after R(Δa) levels off. The analysis is capable of predicting the usual D vs. Δa curves in the literature which have high initial values and fall monotonically to a plateau at large Δa. It also predicts that D curves for CCT testpieces should be higher than those for SENB/CT, as found in practice. The possibility that D curves at some intermediate Δa may dip to a minimum below the levelled‐off value at large Δa is predicted and confirmed by experiment. Recently reported D curves that have smaller initial D than the D‐values after extensive propagation can also be predicted. The testpiece geometry and crack tip R(Δa) conditions required to produce these different‐shaped D vs. Δa curves are established and confirmed by comparison with experiment. The energy dissipation rate D vs. Δa is not a transferable property as it depends on geometry. The material characteristic R(Δa) may be the ‘transferable property’ for scaling problems in ELPL fracture. How it can be deduced from D vs. Δa curves (and by implication, J_R vs. Δa curves) is established.     

SBR工艺发展应用综述

关于SBR工艺的书籍和文章很多。本文在这些资料的基础上整理总结 ,对经典SBR工艺的应用进行了综述 ,归纳了经典SBR工艺的特点 ,介绍了各种新型SBR工艺。     

Power moves: Complementarity in dominant and submissive nonverbal behavior.

Two studies examine complementarity (vs. mimicry) of dominant and submissive nonverbal behaviors. In the first study, participants interacted with a confederate who displayed either dominance (through postural expansion) or submission (through postural constriction). On average, participants exposed to a dominant confederate decreased their postural stance, whereas participants exposed to a submissive confederate increased their stance. Further, participants with complementing responses (dominance in response to submission and submission in response to dominance) liked their partner more and were more comfortable than those who mimicked. In the second study, complementarity and mimicry were manipulated, and complementarity resulted in more liking and comfort than mimicry. The findings speak to the likelihood of hierarchical differentiation (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

A single-grain approach applied to the modeling of recrystallization kinetics for cold-rolled single-phase metals

A comprehensive model for the recrystallization kinetics is proposed which incorporates both microstructure and the textural components in the deformed state. The model is based on the single-grain approach proposed previously. The influence of the as-deformed grain orientation, which affects the stored energy via subgrain size and sub-boundary misorientation, is taken into account. The effects of the deformed grain geometry, the nucleation-site density, and the initial grain size prior to deformation on the recrystallization kinetics are assessed. The model is applied to the recrystallization kinetics of a cold-rolled AA1050 alloy.     

提高中碳锰铁精炼电炉炉龄的实践

通过对精炼电炉炉体改造和出铁口材质、砖型的更新，解决了在中碳锰铁生产过程中炉眼易损问题，提高了炉龄，降低了生产成本。     

自蔓延高温合成TiNi多孔体合金

为了开发新型的生体材料，本文对自蔓延高温合成TiNi多孔体合金——人造骨材料进行了研究。以单质钛粉和镍粉作原料，在氩气保护条件下，采用预热点燃模式和热爆模式制得了不同形态的多孔TiNi形状记忆合金。采用SEM和XRD分析了样品的孔洞特征和相组成，测试了其力学性能，并研究了合成条件参数与样品表面形貌和孔隙状态之间的关系。结果表明，用SHS法制备TiNi多孔体合金是可行的。     

唐钢ER70S-6焊丝钢的生产工艺研究及质量分析

介绍了唐钢ER70S-6焊丝钢的特点，对盘条质量进行了分析。对该钢化学成分、冶炼和轧制工艺进行了优化研究，使其综合性能明显改善。