Spray-coated PDMS/PVDF composite membrane for enhanced butanol recovery by pervaporation

In this study, spray-coating was used to prepare dihydroxypolydimethylsiloxane (PDMS) composite membranes with high flux and separation factor for biobutanol recovery from aqueous solution. A thin, smooth, and defect-free PDMS layer was prepared by spray-coating on polyvinylidene difluoride ultrafiltration membrane with little PDMS penetration. The effects of process parameters for membrane fabrication and pervaporation on membrane performance were investigated. A membrane with 2 μm active layer was obtained with a high flux of 1306.9 g/m² h. The optimal membrane with the highest pervaporation separation index (PSI) (19.15 kg/m² h) showed a total flux of 530.6 g/m² h and a separation factor of 36.1 at 37°C, and a PSI of 65.61 kg/m² h and a flux of 1927.0 g/m² h at 70°C. Membrane performance was affected by feed composition and temperature. Acetone-butanol-ethanol solution and fermentation broth gave lower butanol fluxes and separation factors compared to butanol model solution.     

基于响应面法的双边长初级永磁直线同步电机多目标优化设计

永磁直线同步电机由于存在边端效应以及齿槽效应,在运行中不可避免地产生推力波动。针对高速大推力密度应用场景,对一种双边长初级PMLSM开展了优化设计。将有限元法与解析法结合,首先独立分析了轴向长度、极弧系数和初级轭部高度等单个参数对电机水平推力和推力波动的影响,并进一步采用Taguchi法筛选显著性较高的结构参数。在此基础上,以提高电磁推力、减小推力波动为优化目标对电机进行响应面分析,得到最终的电机尺寸优化参数。最后制作样机并搭建实验平台,验证了所提优化方法的有效性。     

A FUZZY NEURAL NETWORK DECISION MODEL ON THE OPERATION PROCESS OF ELECTRIC FURNACE FOR CLEANING SLAG AND ITS APPLICATION

ＡＦＵＺＺＹＮＥＵＲＡＬＮＥＴＷＯＲＫＤＥＣＩＳＩＯＮＭＯＤＥＬＯＮＴＨＥＯＰＥＲＡＴＩＯＮＰＲＯＣＥＳＳＯＦＥＬＥＣＴＲＩＣＦＵＲＮＡＣＥＦＯＲＣＬＥＡＮＩＮＧＳＬＡＧＡＮＤＩＴＳＡＰＰＬＩＣＡＴＩＯＮ￥Ｐｅｎｇ，Ｘｉａｏｑｉ；Ｍｅｉ，Ｃｈｉ；Ｚｈ...     

热丝化学气相沉积法原位制备的MgB2超导薄膜

用热丝化学气相沉积法(HFCVD)在蓝宝石基片上原位制备了MgB2超导薄膜,并用XRD、SEM和dc SQUIDs研究了基片温度和时间对薄膜相组成、表面形貌和超导临界转变温度Tc的影响.结果表明,HFCVD原位生长MgB2薄膜可以抑制MgO杂质的生成.基片温度在500℃以下,MgB4杂相容易出现;在500℃以上时,可以消除MgB4杂相;在600℃时,获得了纯单相的MgB2薄膜,其超导临界转变温度达到36 K.随基片温度升高,薄膜结晶性、致密度和超导临界转变温度提高.     

LiF-KF熔盐溶液热力学性质Monte Carlo法计算机模拟研究

本文用 Monte Carlo法对同离子系LiF-KF熔盐溶液的结构和性质进行了计算机模拟.对各离子间的偏径向分布函数和混合热、位能分布等的计算表明,LiF与KF熔盐混合后,Li~+,F~-离子间平均距离减少,与互易盐系LiF-KCl溶液的模拟结果相似.混合热的计算结果与实测值相当接近。混合热产生的原因:正离子间排斥能减少;正负离子间吸引能减少;负离子间排斥能减少。     

Operation optimization of concentrate burner in copper flash smelting furnace

The software that simulates the flow, temperature, concentration and the heat generation field in the Outkumpu flash smelting furnace, was developed by a numerical method of the particle-gas flow together with some chemical reaction models. Many typical operating conditions were chosen for simulation in order to obtain the effect of the distribution air, process air, central oxygen and the oil-burner position etc. The concepts about optimum op-eration, 3C(concentration of high temperature, high oxygen and laden concentrate particles), are concluded from these simulated results, which have been checked primarily by operational experiments.     

副保险杠翻边冲孔模的设计与改进

介绍了副保险杠翻边冲孔模的设计要点,同时通过改进结构,使模具的装配和调整变得简便。     

Finishing effects of spiral polishing method on micro lapping surface

This study presents a spiral polishing method and a device for micro-finishing purposes. This novel finishing process has wider application than traditional processes. This offers both automation and flexibility in final machining operations for deburring, polishing, and removing recast layers, thereby producing compressive residual stresses even in difficult to reach areas. Applying of this method can obtain a fine polished surface by removing tiny fragments via a micro lapping generated by transmission of an abrasive medium through a screw rod. The effect of the removal of the tiny fragments can be achieved due to the function of micro lapping. The method is not dependent on the size of the work-piece's application area in order to carry out the ultra precise process. The application of this research can be extended to various products of precision ball-bearing lead screw. The proposed method produces products with greater precision and more efficiently than traditional processes, in terms of processing precisions and the surface quality of products. These parameters used in achieving maximum material removal rate (MRR) and the lowest surface roughness (SR) are abrasive particle size, abrasive concentration, gap, revolution speed and machining time.     

抗菌功能性铝基材料的制备及表征

通过交流电沉积的方法在铝阳极氧化膜的孔内沉积金属铜,制备了铝基抗菌功能性材料;测试了沉积铜的铝阳极氧化膜的抗菌性能.结果表明:电沉积铜的铝阳极氧化膜对大肠杆菌、绿脓杆菌、粪链球菌和金黄色葡萄球菌的抗菌率均大于95%.透射电子显微镜表征了铜在氧化膜孔内的沉积形貌,铜在铝阳极氧化膜孔内呈连续的线状形貌,直径为25 nm.     

无芯薄壁长矩形管弯曲模设计

介绍了避免无填料和衬芯的长矩形管弯曲成形后管壁出现内陷及折痕的工艺,模具结构特点及设计中注意的事项,模具结构合理,便于加工、装配及使用。对该类工件的弯曲成形有一定的参考价值。