离子束增强沉积CrN膜层及其微动摩擦学性能研究

以不同氮离子辅助轰击能量制备CrN膜层．利用纳米压入仪及显微硬度计分别测试单晶Si片上膜层的硬度及断裂韧度K1C．使用XRD、XPS及EPMA分析离子轰击能量对镀层组织结构的影响。结果表明，采用能量较低的氮离子轰击得到的涂层，由于金属Cr的存在，涂层硬度虽有所降低，但断裂韧度K1C数值较高。选择较低的4keV辅助轰击能量，在M2高速钢基体上沉积CrN涂层，膜层在空气介质中表现出优异的耐磨减摩特性.但在水介质条件下，由于膜层接触区域的去钝化，再钝化使腐蚀和磨损相互加速，导致CrN膜层摩擦系数，尤其是磨损量明显高于基材。     

脉冲磁场下铝合金定向凝固磁场分布数值模拟

采用ANSYS 8.0有限元分析软件对铝合金脉冲磁场定向凝固磁场分布作了数值模拟,得到了凝固过程中的磁场分布状态.结果表明:在试样中心附近磁感应强度较强,而在端部较弱.模拟结果和实验测得结果相符合.通过数值模拟,不仅可以初步了解凝固过程中的磁场分布状态,而且有助于进一步研究凝固组织细化的原因.     

从斜轧技术发展看自动轧管机组的改造方向

对斜轧技术的发展和传统斜轧“横锻效应”的副作用作的介绍和分析，并列举几种新型的斜轧穿孔和轧管设备的特点，提出用三步成型轧管工艺代替老式多工序轧管工艺以改造现有自动轧管机组。     

Friction stir welding of AZ31 magnesium alloy

Friction stir welding (FSW) is an new solid-phase joining technology which has more advantages over fusion welding methods in welding of aluminum and other non-ferrous metals. The effects of welding parameters on mechanical properties and microstructure during friction stir welding of AZ31 magnesium alloy were studied in this paper. Microstructures and mechanical properties of the joints were investigated by means of optical microscopy, scanning electric microscopy ( SEM ) , micro-hardness analysis, and tensile test. Experimental results show that the magnesium alloy can be successfully welded by FSW method, and the ultimate tensile strength (UTS) of FSW joint reaches up to 90 percent of base metal. The microstructures of welded joints exhibit the variation from dynamically recrystallized fine grains to greatly deformed grains. Hardness in nugget zone was found lower than the base metal but not too obvious.     

挤压模具型腔轮廊曲线优化拟合分析

采用三次样条函数插值和Bezier曲线拟合两种方法来完成挤压模具型腔轮廓形状的优化设计 ,以挤压表面载荷沿凹模型腔轮廓表面均匀分布来提高模具寿命为优化目标 ,运用刚塑性有限元分析和修正的序列二次规划算法相结合的方法 ,获得了各自优化了的凹模型腔轮廓曲线。通过有限元软件验证了优化结果的有效性和可行性。将这些方法应用于气门及其他类似零件的生产 ,证明了优化的凹模型腔轮廓曲线对提高模具使用寿命有显著效果     

Infrared heat treatment of Ti-6Al-4V with electroplated Cu

The objective of this study is to investigate an innovative infrared (IR) technique to enhance adhesion of electroplated copper (Cu) on Ti-6Al-4V without dichromate dipping. The ultimate goal is to develop a Cu coating process on Ti-6Al-4V without hazardous hexavalent chromium (Cr) solution treatments. Cu coatings of around 50 μm were electroplated on Ti-6Al-4V specimens at a current density of 0.03 A/cm² in an acidic Cu solution. To improve adhesion of coatings, IR heat treatments were performed on the Cu-coated samples at different temperatures and durations: 860 °C for 600 s and 875 °C for 20–120 s. This process was accomplished in an attempt to replace the use of dichromate dipping before electroplating. For samples heat treated at 860 °C, no bonding existed, even after 600 s. It is believed that solid-state diffusion prevailed at 860 °C and that 600 s was not enough for sufficient diffusion to occur. Adhesion was poor when samples were heat treated at 875 °C for 20 s. Excellent adhesion was observed when the heat treatment holding time was increased to 40 s. For 90 s, the surface appearance of coatings partially changed from Cu-colored to a grayish color. There was no Cu left on the surface after a 120 s heat treatment. From optical microscopic observations on sample cross sections, an interlayer between the Cu and Ti-6Al-4V formed when heat treated at 875 °C for 40 s and longer. The interlayer thickness increased as the holding time increased, until depletion of Cu. The sheet resistivity of coated specimens was on the order of pure Cu for samples heat treated at 875 °C and less than 90 s. During the 875 °C heat treatment, the following occurred: solid-state diffusion of Cu in Ti-6Al-4V, formation of eutectic solutions, dissolution of Cu and Ti-6Al-4V into the liquid phase, and the formation of intermetallic compounds. The lowest eutectic temperature of 875 °C played a key role in this innovative process of Cu coating on Ti-6Al-4V. This paper was presented at the 2nd International Surface Engineering Congress sponsored by ASM International, on September 15–17, 2003, in Indianapolis, Indiana and appears on pp. 403–10 of the Proceedings.     

超精密加工伺服系统滑模控制技术研究

为实现超精密加工伺服系统高精度跟踪控制，建立了交流水磁同步电机伺服系统模型，研究了带扰动观测器补偿的滑模变结构控制方法，仿真结果表明，该控制策略有效地抑制了负载扰动引起的抖振，对参数波动也有较强的适应能力，可以有效地提高系统的跟踪特性。     

Microstructure, mechanical and tribological properties of Cr1−xAlxN films deposited by pulsed-closed field unbalanced magnetron sputtering (P-CFUBMS)

Nanocrystallized Cr_1−xAl_xN films with various Al contents (0 to 68 at.%) were deposited by pulsed closed field unbalanced magnetron sputtering (P-CFUBMS). The effects of aluminum content on the microstructure, mechanical and tribological properties of the Cr_1−xAl_xN films have been investigated. It was found that the hardness and elastic modulus of Cr_1−xAl_xN films increased with increasing Al contents in the films and reached the highest value of 36 GPa and 370 GPa, respectively, at an Al content of 58.5 at.%. Addition of Al beyond 64.0 at.% resulted in a change in crystal structure from B1 cubic to B4 hexagonal phase. The wear resistance improved gradually with the increase of Al in the Cr_1−xAl_xN films. A combination of the abrasive and adhesive wear mechanism was proposed based on the SEM and EDS analysis of the wear track. The steady state dry coefficient of friction measured against a WC ball for the Cr_1−xAl_xN films were in the range of 0.36-0.55, and the wear rate was in the 10^− 6 mm³ N^− 1 m^− 1 range.     

RELATIONSHIP BETWEEN PRIMARY MORPHOLOGY AND CRYSTAL STRUCTURE OF CARBIDES GROWING IN SUPERALLOYS

The SEM analysis of decply etched specimens of Ni-base superalloys K38 and K19H+Ta in-dicates that both the primary morphologies under normal growth conditions and the finalmorphologies near equilibrium of MC carbides are octahedral blocks.The classification ofMC crystal faces by means of PBC(Periodic Bond Chains)theory confirms that{100},{110}and{111}are F faces,and that{212}are S faces.The calculations of the attachmentenergy for each F face show that{111}are most easily appeared.It has also been inferred thatone of the MC growth units is a coordination octahedron composed of one metal atom sur-rounded by six carbon atoms.The octahedral growth units can be attached to the growth sur-faces of MC carbides through laver stacking mechanism on the{111}faces.     

基于Web的车身覆盖件模具标准件库系统的研究

通过对车身覆盖件模具标准件和典型结构件的总结与归纳．使用Microsoft．NET平台建立了基于Web的车身覆盖件模具三维参数化标准库。系统主要包括标准件参数数据库、标准件特征信息库、标准件模型库，此外为方便设计人员选型，还提供了标准件计算、分析与决策模块。