颗粒增强钢基复合材料轧辊研究的现状

分析了轧辊的发展趋势,探究了颗粒增强钢基复合材料的力学性能,揭示了颗粒增强钢基复合材料轧辊的性能优势;概述了颗粒增强钢基复合材料轧辊的发展现状和各种制备工艺,并简要分析了轧辊材料的发展.     

主跨348m+348m三塔单索面PC梁斜拉桥

宜昌市夷陵长江大桥采用三塔斜拉桥，总体布置为(128．08 348 348 120．35)m。介绍了该桥的合理性及结构特点。     

Ionothermal synthesis of a three-dimensional zinc phosphate with DFT topology using unstable deep-eutectic solvent as template-delivery agent

A three-dimensional zinc phosphate compound with DFT topology, designated as ZnPO₄-EU1, has been synthesized by an ionothermal approach from the system HF-ZnO–P₂O₅-choline chloride-imidazolidone. Ethylenediamine, derived from decomposition of the imidazolidone component of the deep-eutectic solvent (DES) itself, is delivered to the synthesis and serves as an appropriate template for ZnPO₄-EU1. Experiments in which the synthesis conditions were varied showed that ZnPO₄-EU1 may be prepared over a wide molar ratio of P/Zn = 0.55–13.0. Powder X-ray diffraction patterns have been obtained at intervals to track the crystallization process of this material. The experimental data show that Zn₃(PO₄)₂ · 4H₂O (a dense phase) was first isolated from the DES after reaction for 1 h. Subsequently, the pure phase of ZnPO₄-EU1 was obtained with increasing crystallization time from 12 h to 72 h. The experimental results show that the nucleation and crystallization take place with relatively low levels of solvent degradation, demonstrating that zinc phosphate with a three-dimensional framework can be synthesized by in situ generation of an appropriate template using an unstable DES at high temperatures (150–200 °C).     

Polyetherimide substrates for future high density optical data storage

Polyetherimide (PEI) substrate for next‐generation high density optical data storage is fabricated and characterized. Cover‐layer incident or first‐surface recording configurations do not require optical properties of the substrate, which are the prerequisite conditions for the conventional material of polycarbonate (PC). Instead of the optical properties, good mechanical properties with a sufficient transcribability are required. Even though PEI has higher glass transition temperature than that of PC, a microscopic transcribability of PEI is comparable with PC by laminating a thermal insulation layer on the backside of a stamper to retard the heat flow. A macroscopic warpage of PEI substrate is smaller than that of PC substrates, which reduces tilt and servo burden. The lowest critical speed coupled with the flutter of PEI substrate is larger than that of PC substrate because of the mechanical properties of PEI. POLYM. ENG. SCI., 48:97–101, 2008. © 2007 Society of Plastics Engineers     

基于USB的155 Mb/s码型发生器的研制

介绍了一种带USB接口的光的155Mb／s码型发生器。伪随机码和其他格式的码型由PC产生通过USB接口进入双口RAM，再经串并变换后由光发射模块发射。该系统可方便地设定各种格式的码型，并同时具备光接口和电接口，可广泛应用于光通信各种实验中，具有重要的实用价值。     

Formation mechanism of 21R AlN-polytypoids in aluminothermic reduction and nitridation process

Synthesis of 21R AlN polytypoids was investigated using Al and ultrafine SiO₂ powder in a flowing nitrogen atmosphere by means of thermal gravity (TG), differential scanning calorimeter (DSC), X-ray diffractometer (XRD) and scanning electronic microscope (SEM) linked with energy dispersive spectrometer (EDS). The results showed that the formation mechanism of AlN polytypoids was different from that in reaction sintering process using Si₃N₄, AlN, Al₂O₃ and other sintering additive as raw materials. It was suggested that firstly Al reduce SiO₂ into Si and is also nitrided into AlN, then AlN, Al₂O₃ and SiO₂ dissolve into silicon liquid until the AlN polytypoids precipitate in saturated liquid in a flowing nitrogen atmosphere at lower than 1700 °C.     

国有公路运输企业改革创效的现实选择

通过对公路运输企业经营实践的考察 ,介绍了国有公路运输企业改革创效的一些现实选择 ,以供运输公司经营借鉴 ,从而摆脱困境 ,取得良好业绩     

Complementary effects of solid lubricants in the automotive brake lining

An experimental investigation was carried out to examine the tribological behavior of NAO (non-asbestos organic) type brake linings containing different volume ratios of graphite and antimony trisulfide (Sb₂S₃). A scale dynamometer was used for friction tests and particular emphases were given to the effect of applied pressure, sliding speed, and temperature on the coefficient of friction according to the relative amounts of the two solid lubricants. Results showed that the brake linings with both solid lubricants exhibited better friction stability and less speed sensitivity than the friction materials containing a single solid lubricant. In particular, the brake lining containing higher concentrations of graphite showed better fade resistance than others during high-temperature friction test.     

数控超声加工的初步工艺试验

介绍在经过数控化改造的两坐标超声加工机床上所进行数控超声加工的初步工艺试验,并讨论试验结果。